Manuel d'utilisation / d'entretien du produit 7D du fabricant Canon
Aller à la page of 292
E INSTRUCTION MANUAL E INSTRUCTION MANUAL ● The “Software Start Guide” is included at the end of this manual. ● This manual is for the EOS 7D installed with firmware version 2.
2 Thank you for purchasing a Canon product. The EOS 7D is a high-performance, digital SLR camera featuring a fine-detail CMOS sensor with about 18.0 effective megapixels, Dual “DIGIC 4”, approx. 100% viewfinder coverage, high-precision and high- speed 19-point AF (all cross-type), approx.
3 Before starting, check that all t he following items have been included with your camera. If anything is missing, contact your dealer . * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) If you purchased a Lens Kit, chec k that the lens is included.
4 Icons in this Manual < 6 > : Indicates the Main Dial. < 5 > : Indicates the Quick Control Dial. < 9 > : Indicates the Multi-controller . < 0 > : Indicates the setting button. 0 , 9 , 7 , 8 : Indicates that the respective function remains active for 4 sec.
5 For first-time DSLR users, Chapters 1 and 2 explain the camera’ s basic operations and shooting procedures. Chapters Introduction Camera basics. 2 Getting St arted 23 Basic Shooting Fully automatic shooting. 51 Image Settings 59 Setting the AF and Drive Modes 87 Advanced Operations Advanced shooti ng features.
6 3 1 2 Introduction 2 Item Check List ....................... ........................................................................... 3 Conventions Used in this Manual ............................................... ....................... 4 Chapters .
7 Contents 5 4 A Customizing a Picture St yle .....................................................................68 A Registering a Picture St yle ........................................... ............................70 B : Setting the White Balanc e .
Contents 8 10 9 6 7 8 Live View Shooting 135 A Live View Shooting. ......................................... ........................................ 136 Shooting Function Settings ......................................................................
9 Contents 13 14 11 12 Printing Images 205 Preparing to Print ........................ ...................................................................206 w Printing........................ .......................................... ...............
10 Power Battery • Charging Î p.24 • Battery check Î p.28 • Battery information check Î p.246 Power outlet Î p.250 Auto power off Î p.46 Lens Attaching/Det aching Î p.31 Zoom Î p.32 Image St abilizer Î p.33 Basic Settings (Menu Functions) Language Î p.
11 Index to Features Self-timer Î p.98 Remote control Î p.1 14 Exposure adjustment Exposure compensation Î p.108 AEB Î p.109 AE lock Î p.1 10 Flash Built-in flash Î p.1 15 • Flash exposure compensation Î p.1 17 • FE lock Î p.1 18 External flash Î p.
12 Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and ca nnot be used underwater . If you accidentally drop the camera into wa ter , promptly consult your nearest Canon Service Center .
13 Handling Precautions LCD Panel and LCD Monitor Although the LCD monito r is manufactured with very high precision technology with over 99.9 9% effective pixels, there might be a few dead pixels among the remaini ng 0.01% or less pixels. Dead pixels displaying only black or red, etc.
14 Quick Start Guide 1 Insert the battery . (p.26) T o charge the battery , see page 24. 2 Atta ch the lens. (p.31) When attaching an EF-S lens, align it with the white index on the camera. For other lenses, align it with the red index. 3 Set the lens focus mode switch to <AF>.
15 Quick Start Guide 6 Set the Mode Dial to < 1 > (Full Auto). (p.52) All the necessary camera settings will be set automatically . 7 Focus the subject. (p.35) Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway , and the camera will focus the subject.
16 For detailed information, reference page nu mbers are provided in parentheses (p.**). Nomenclature HDMI mini OUT terminal (p.185) Remote control terminal (p.112) (N3 type) PC terminal (p.134) Hot shoe (p.133) Built-in flash/AF-assist beam (p.115/90) EF-S lens mount index (p.
17 Nomenclature Tripod socket Extension system terminal Battery compartment cover (p.26) Battery compartment cover release lever (p.26) < V > Focal plane mark < 9 > Multi-controller (p.36) Viewfinder eyepiece Eyecup (p.112) Dioptric adjustment knob (p.
18 Nomenclature LCD Panel The display will show only th e settings currently applied. S hutter speed Busy ( buSY ) Built-in flash recycling ( buSY ) < A > Highlight tone priority (p.
19 Nomenclature Viewfinder Information The display will show only th e settings currently applied. Spot metering circle (p.107) Grid (p.49) Area AF frame/ Zone AF frame (p.
20 Nomenclature Mode Dial Fully-Automatic Modes All you do is press the shutter button. Fully-automatic shooting suitable for the subject. 1 : Full Auto (p.52) C : Creative Auto (p.55) F : Bulb (p.1 1 1) a : Manual exposure (p.106) f : Aperture-priority AE (p.
21 Nomenclature Lens Lens with a distance scale Lens without a distance scale Focus mode switch (p.31) Lens mount index (p.31) Contacts (p.13) Hood mount (p.274) Filter thread (front of lens) (p.274) Focusing ring (p.96,149) Zoom ring (p.32) Zoom position index (p.
22 Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.24). Battery Charger LC-E6E Charger for Battery Pack LP-E6 (p.24). Battery pack slot Charge lamp Power plug IMPORT ANT SAFETY INSTRUCTIO NS-SA VE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULL Y FOLLOW THESE INSTRUCTIONS.
23 Getting Started This chapter explains preparatory step s before you start shooting and basic camera operations. Attaching the S trap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
24 1 Remove the protective cover . 2 Atta ch the battery . As shown in the illustration, attach the battery securely . T o detach the battery , follow the above procedure in reverse. 3 Recharge the battery . For LC-E6 As shown by the arrow , flip out the battery charger ’s prongs and insert the prongs into a power outlet.
25 Charging the Battery Recharge the battery on th e day before or on the day it is to be used. Even during non-use or storage, a charged battery will gradually discharge and lose its power . After recharging the battery , detach it and unplug the power cord or prongs from the power outlet.
26 Load a fully charged Battery Pa ck LP-E6 into the camera. The camera’ s viewfinder will become bri ght when a battery is installed, and darken when the battery is removed. 1 Open the battery compartment cover . Slide the lever as shown by the arrow and open the cover .
27 < 1 > : The camera turns on. < 2 > : The camera is turned off and does not operate. Set to this position when not using the camera. Whenever you set the power switch to < 1 > or < 2 >, the sensor cleaning will be executed automatica lly .
28 Turning on the Power When the power switch is set to < 1 >, the battery level will be indicated in one of six levels: A blinking battery icon ( b ) indicates that the battery will be exhausted soon.
29 Although the thickness is different between the two types of CF (CompactFlash) cards, the camera is compatible with both types. It is also compatible with Ultra DMA (UDMA) cards and hard disk-type cards. 1 Open the cover . Slide the cover as shown by the arrow to open it.
30 Installing and Removing the CF Card 1 Open the cover . Set the power switch to < 2 >. Make sure the access lamp is off, then open the cover . 2 Remove the card.
31 1 Remove the caps . Remove the rear lens cap and the body cap by turning them as shown by the arrow . 2 Atta ch the lens. Align the EF-S lens with the camera’s white EF-S lens mount index and turn the lens as shown by the arrow until it clicks in place.
32 Attaching and Detaching a Lens T o zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. T urning the zoom ring after achieving focus may throw off the focus slightly . While pressing the lens release button, turn the lens as shown by the arrow .
33 When you use the IS lens’ built-in Image S tabilizer , camera shake is corrected to obtain a less blurred s hot. The procedure explained here is based on the EF-S15-85mm f/3.5-5.6 IS USM lens as an example. * IS stands for Image S tabilizer . 1 Set the IS switch to < 1 >.
34 T urn the dioptric adjustment knob. T urn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.1 12). T o obtain sharp images, hold the ca mera still to minimize camera shake.
35 Basic Operation The shutter button has two steps. Y ou can press the shutter button halfway . Then you can further press the shutter button completely . Pressing halfway This activates autofocusing and automatic exposure metering that sets the shutter speed and aperture.
36 Basic Operation (1) Af ter pressing a button, turn the < 6 > dial. When you press a button, its function remains selected for 6 seconds ( 9 ). During this time, you can turn the < 6 > dial to set the desired setting. When the function turns off or if you press the shutter button halfway , the camera will be ready to shoot.
37 Basic Operation Before using the < 5 > dial, set the Quick Control Dial switch to < J >. (1) Af ter pressing a button, turn the < 5 > dial. When you press a button, its function remains selected for 6 seconds ( 9 ). During this time, you can turn the < 5 > dial to set the desired setting.
38 The shooting settings are displayed on the LCD monitor where you can directly select and set the functions. This is called the Quick Control screen. 1 Display the Quick Control screen. Press the < Q > button. X The Quick Control screen will appear ( 7 ).
39 Q Using the Quick Control Screen On the Quick Control screen, select the function and press < 0 >. The respective setting screen will then appear (except for the shutter speed and aperture). T urn the < 5 > or < 6 > dial to change the setting.
40 Y ou can set various functions wit h the menus such as the image- recording quality , date/time, etc. While looking at the LCD monitor , use the < M > button on the camera back and the < 6 > < 5 > dials. 3 Menu Operations * Some menu tabs and menu items are not displayed in the fully-automatic modes.
41 3 Menu Operations 1 Display the menu. Press the < M > button to display the menu. 2 Select a t ab. T urn the < 6 > dial to select a tab. 3 Select the desired item. Tu rn t h e < 5 > dial to select the item, then press < 0 >.
42 1 Select [Language K ]. Under the [ 6 ] tab, select [ Language K ] (the third item from the top), then press < 0 >. 2 Set the desired language. T urn the < 5 > or < 6 > dial to select the language, then press < 0 >. X The interface language will change.
43 Before You Start When you turn on the power for the first time or if the date/time has been reset, the Date/T ime/Zone sett ing screen will appear . Follow steps 2 to 5 to set the current date, time, and time zone. Note that the date/time appended to recorded images will be based on this date/time setting.
44 Before You Start 4 Set the daylight saving time. Set if necessary . T urn the < 5 > dial to select [ Y ]. Press < 0 > so < r > is displayed. Tu rn t h e < 5 > dial to select [ Z ], then press < 0 >. When the daylight saving time is set to [ Z ], the time set in step 2 will advance by 1 hour .
45 Before You Start If the card is new or was previous ly formatted by another camera or personal computer , formatting the ca rd with the camera is recommended. When the card is formatted, all images and data in the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep.
46 Before You Start Y ou can change the auto power-off time for the camera to turn of f automatically after a certain period of non-operation. If you do not want the camera to turn off automatically , set this to [ Off ]. After the power turns off, you can turn on the came ra again by pressing the shutter button or other button.
47 Before You Start The camera’s shooting settings and menu settings can be reverted to the default. 1 Select [Clear all camera settings]. Under the [ 7 ] tab, select [ Clear all camera settings ], then press < 0 >. 2 Select [OK]. T urn the < 5 > dial to select [ OK ], then press < 0 >.
48 Before You Start Camera Settings Live View Shooting Settings VF grid display Disable Live View shooting Enable Auto power off 1 min. Beep On AF mode Live mode Release shutter without card Enable Grid display Off Exposure simulation Enable Review time 2 sec.
49 The grid and electronic level can be displayed to help keep the camera aimed straight. The grid is displayed in the viewfinder , and the electronic level is displayed on the LCD monitor . 1 Select [VF grid display]. Under the [ 6 ] tab, select [ VF grid display ], then press < 0 >.
50 Displaying the Grid and Electronic Level 1 Press the < B > button. Each time you press the < B > button, the screen display will change. Display the electronic level. If the electronic level does not appear , set the menu’s [ 7 INFO. button display options ] option to display the electronic level (p.
51 Basic Shooting This chapter explains how to use the fully-automatic modes ( 1 / C ) on the Mode Dial for best results. With the fully-automatic modes ( 1 / C ) , all you do is point and shoot and the camera sets everything automatically (p.
52 1 Set the Mode Dial to < 1 >. 2 Aim the Area AF frame over the ta rget subject. All the AF points will be used to focus, and generally the closest object will be focused. Aiming the center of the Area AF frame over the subject will make focusing easier .
53 1 Fully Automatic Shooting The focus confirmation light < o > blinks and focus is not achieved. Aim the center of the Area AF fram e over an area having good contrast, then press the shutter button halfway (p.96). If you are too close to the subject, move away and try again.
54 Depending on the scene, position the subj ect toward the left or right to create a balanced background and good perspective. In the < 1 > (Full Auto) mode, while you press the shutter button halfway to focus a still subject, t he focus will be locked.
55 The < 1 > Full Auto mode takes care of everything, whereas the < C > Creative Auto mode enables you to easily change the picture’s brightness, depth of field, color tone (Picture S tyle), etc. The default settings are the same as the < 1 > (Full Auto) mode.
C Creative Auto Shooting 56 (1) Flash firing < a > (Auto firing), < D > (Flash on), or < b > (Flash off) can be selected. (2) Blurring/sharpening the background If you move the index mark toward the left, the background will look more blurred.
57 C Creative Auto Shooting (4) Image effects Besides the standard image ef fect, you can set it for portraits, landscapes, or black-and-white p hotos. (p.66: Picture S tyle) < P > (S tandard): S tandard image effect applicable to most scenes. < Q > (Smooth skin tones): Effective for close-ups of women or children.
C Creative Auto Shooting 58 Y ou can set how long the image is displayed on the LCD monitor immediately after capture. T o keep the image displayed, set [ Hold ]. T o not have the image displayed, set [ Off ]. 1 Select [Review time]. Under the [ 1 ] tab, select [ Review time ], then press < 0 >.
59 Image Settings This chapter explains image -related function settings: Image-recording quality , ISO speed, Picture S tyle, white balance, Auto Lighting Optimizer , lens peripheral illumination correction, etc.
60 Y ou can select the pixel count and th e image quality . Six JPEG recording quality settings are provided: 73 / 83 / 74 / 84 / 76 / 86 . Three RA W recording quality settings are provided: 1 , 41 , and 61 (p.62). 1 Select [Quality]. Under the [ 1 ] tab, select [ Quality ], then press < 0 >.
61 3 Setting the Image-recording Quality Guide to Image-recording Quality Settings (Approx.) Figures for the file size, possible shots, and maximu m burst during continuous shooting are based on C anon’s testing st andards (ISO 100 and St andard Picture S tyle) using a 8 GB card.
62 3 Setting the Image-recording Quality A RA W image is raw data output by the image sensor converted to digital data. It is recorded to the card as is, and you can select the quality as follows: 1 , 41 , or 61 . A 1 image can be processed with [ 3 RA W image processing ] menu (p.
63 3 Setting the Image-recording Quality If the current recording quality is JPEG only , you can press the < P > button to also capture a RA W image ( 1 by default) at the same time. If the current recording quality is RA W only , press the button to also capture a JPEG image ( 73 by default).
64 Set the ISO speed (image sensor ’s se nsitivity to light) to suit the ambient light level. In th e fully-automatic modes ( 1 / C ), the ISO speed is set automatically (p.65). 1 Press the < m > button. ( 9 ) 2 Set the ISO speed. While looking at the LCD panel or viewfinder , turn the < 6 > d ial.
65 i : Setting the ISO Speed N If the ISO speed is set to “ A ” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway . As indicated below , the ISO speed will be set automatically to suit the shooting mode.
66 By selecting a Picture S tyle, you can obtain image effect s matching your photographic expression or the subject. In the < 1 > (Full Auto) mode, you cannot select the Picture S t yle. 1 Press the < A > button. When the camera is ready to shoot, press the < A > button.
67 A Selecting a Picture Style N S Neutral This Picture S tyle is for users wh o prefer to process images with their computer . For natural colors and subdued images. U Faithful This Picture S tyle is for users wh o prefer to process images with their computer .
68 Y ou can customize a Picture S tyle by adjusting individual parameters like [ Sharpness ] and [ Contrast ]. T o see the resulting effects, ta ke test shots. T o customize [ Monochrome ], see the next page. 1 Press the < A > button. 2 Select a Picture Style.
69 A Customizing a Picture Style N For Monochrome, you can also set [ Filter effect ] and [ T oning effect ] in addition to [ Sharpness ] and [ Contrast ] explained on the preceding pag e. k Filter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more.
70 Y ou can select a base Picture S tyle such as [ Portrait ] or [ Landscape ], adjust its p arameters as desir ed and register it under [ User Def. 1 ], [ User Def. 2 ], or [ User Def. 3 ]. Y o u can create Picture S tyl es whose parameter setti ngs such as for sharpness and contrast are different.
71 A Registering a Picture Style N 6 Set the parameter . T urn the < 5 > dial to set the parameter as desired, then press < 0 >. For details, see “Customizing a Picture S tyle” on pages 68-69. Press the < M > button to register the new Picture S tyle.
72 White balance (WB) is for making th e white areas look white. Normally , the < Q > (Auto) setting will obtain the correct white balance. If natural- looking colors cannot be obtained with < Q >, you can select the white balance for each light source or set it manually by shooting a white object.
73 B : Setting the White Balance N Custom white balance enables you to manually set the white balance for a specific light source for better accuracy . Do this procedure under the actual light source to be used. 1 Photograph a white object. Look through the viewfinder and the area within the dotted line should cover a solid-white object.
74 B : Setting the White Balance N Y ou can set the white balance’s color temperature numerically in Kelvin. This is for advanced users. 1 Select [White balance]. Under the [ 2 ] tab, select [ White balance ], then press < 0 >. 2 Set the color temperature.
75 Y ou can correct the white balance t hat has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter . Each color can be corrected to one of nine levels.
76 u White Balance Correction N With just one shot, three images having a different co lor tone can be recorded simultaneously . Based on the color tem perature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias.
77 If the image comes out dark or the cont rast is low , the brightness and contrast can be corrected automatic ally . With JPEG images, the correction is done when the image is captured. For RA W images, it can be corrected with Digital Photo Professional (provided software).
78 Due to the lens characteristics, the f our corners of the picture might look darker . This is called lens light fall- off or drop in peripheral illumination. With JPEG images, the correction is done when the image is captured. For RA W images, it can be corrected with Digital Photo Professional (provided software).
79 3 Lens Peripheral Illumination Correction The camera already contains lens peripheral illumination correction data for about 25 lenses. In step 2, if you select [ Enable ], the peripheral light correction will be applied automatically for any lens whose correction data has been registered in the camera.
80 Y ou can freely create and select the folder where the captured images are to be saved. This is optional since a folder will be created automatically for saving captured images. 1 Select [Select folder]. Under the [ 5 ] tab, select [ Select folder ], then press < 0 >.
81 3 Creating and Selecting a Folder With the Select folder screen displayed, turn the < 5 > dial to select the desired folder , then press < 0 >. X The folder where the captured images will be saved will be selected. Subsequent captured images will be recorded into the selected folder .
82 The file name has four alphanumeric characters followed by a four-digit image number (p.84) and extension. The first four characters will be “IMG_” by default, but you can change this. With “User setting1”, you can change and register the four characters as desired.
83 3 Changing the File Name 4 Exit the setting. Enter the required number of alphanumeric characters, then press the < M > button. X The new file name will be registered and the screen in step 2 will reappear . 5 Select the registered file name.
84 The four-digit file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder . Y ou can change how the file number is assigned. 1 Select [File numbering].
85 3 File Numbering Methods Restarting the file numbering from 0001 each time the card is replaced or a new folder is created. Whenever the card is replaced or a new folder created, the file numbering starts from 0001. This is convenient if you want to organize images according to cards or folders.
86 The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In the fully-automatic modes ( 1 / C ), sRGB is set automatically .
87 Setting the AF and Drive Modes The 19 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. Y ou can also select the AF mode and drive mode best matching the shooting co nditions and subject.
88 Select the AF mode suiting the shooti ng conditions or subject. In fully- automatic modes ( 1 / C ), “AI Focus AF” is set automatically . 1 On the lens, set the focus mode switch to <AF>. 2 Press the < o > button. ( 9 ) 3 Select the AF mode.
89 f : Selecting the AF Mode N Suited for still subjects. When you press the shutter button halfway , the camera will focus only once. When focus is achi eved, the AF point which achieved focus will be displayed, and the focus confirmation light < o > in the viewfinder will also light.
90 f : Selecting the AF Mode N AI Focus AF switches the AF mode from One-Shot AF to AI Servo AF automatically if the still subject start s moving. After the subject is focused in the One-Shot AF mode, if the subject starts moving, the camera will detect the movement and change the AF mode automatically to AI Servo AF .
91 As default setting, the following three AF area selection modes can be selected. See the next page for the selection procedure. Single-point AF (Manual selection) (p.93) Select one AF point to focus. Zone AF (Manual selection of a zone) (p.94) The 19 AF points are divided into five zones for focusing.
92 S Selecting the AF Area N Select the AF area selection mode. Press the < S > button. ( 9 ) Look through the viewfinder and press the < B > button. X Press the < B > button to change the AF area selection mode. By default, the button changes the mode to single-point AF , Zone AF , and 19-point AF .
93 The AF areas are explained starting with the smallest one. Although this is the same as single-point AF , the selected AF point < O > covers a smaller pinpoint area to focus. Effective for pinpoint focusing overlapping subjects such as an animal in a cage.
94 AF Area Selection Modes The 19 AF points are divided into five zones for focusing. All the AF points in the selected zone are used for the automatic selection of the AF point. It makes achieving focus easier than with single-point AF or AF point expansion and it is ef fective for moving subjects.
95 AF Area Selection Modes With lenses whose maximum aperture is larger than f/5.6 With all AF points, cross-ty pe AF sensitive to both ve rtical and hor izontal lines is possible. With the following lenses, t he peripheral AF points will be vertical- line or horizontal-line sensitive only .
96 Autofocus can fail to achieve focus (the focus confirmation light < o > blinks) with certain subjects such as the following: Subjects difficult to focus V ery low-contrast subjects (Example: Blue sky , solid-color walls, etc.
97 Single and continuous drive modes are provided. In the < 1 > (Full Auto) mode, single shooting is set automatically . 1 Press the < o > button. ( 9 ) 2 Select the drive mode. While looking at the LCD panel, turn the < 5 > dial. u : Single shooting When you press the shutter bu tton completely , one shot will be take n.
98 Use the self-timer when you want to be in the picture. The < Q > (10 sec. timer) can be used in all shooting modes. 1 Press the < o > button. ( 9 ) 2 Select the self-timer . Look at the LCD panel and turn the < 5 > dial to select the self-timer .
99 Advanced Operations In the d / s / f / a / F shooting modes, you can select the shutter speed, aperture, and other camera settings to change the exposure and obtain the desired result. The M icon on the right of the page title indicates that the function can be used when the Mode Dial is set to < d / s / f / a / F >.
100 The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * < d > stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to < d >. 2 Focus the subject. Look through the viewfinder and aim the selected AF point over the subject.
101 d : Program AE If the “ 30 "” shutter speed and the maximum aperture blink, it indica tes underexposure. Increase the ISO speed or use flash.
102 In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the correct exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or moving subject.
103 s : Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. T urn the < 6 > dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure.
104 In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the correct exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
105 f : Aperture-Priority AE Press the depth-of-field preview button to stop down the lens to the current aperture setting. Y ou can check the depth of field (range of acceptable focus) through the viewfinder . Depth of Field Preview N If the “ 30 "” shutter speed bl inks, it indicates underexposure.
106 In this mode, you set both the shutter speed and aperture as desired. T o determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-a vailable handheld exposure meter . This method is called manual exposure.
107 Y ou can select one of four methods to measure the subject brightness. In fully-automatic modes ( 1 / C ), evaluative metering is set automatically . 1 Press the < n > button. ( 9 ) 2 Select the metering mode. While looking at the LCD panel, turn the < 6 > dial.
108 Exposure compensation can increase (brighter) or decrease (darker) the standard exposure set by the camera. Although you can set the exposure co mpensation up to ±5 stops in 1/3- stop increments, the exposure co mpensation indicator on the LCD panel and in the viewfinder can only di splay the setting up to ±3 stops.
109 By changing the shutter speed or aperture automatically , the camera brackets the exposure up to ±3 st ops in 1/3-stop increment s for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo. comp./AEB].
110 Use AE lock when the ar ea of focus is to be di fferent from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the < A > button to lock the exposure, then recompose and take the shot. This is called AE lock.
111 When bulb is set, the shutter stays open while you hold down the shutter button completely , and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures.
112 F : Bulb Exposures If you take a picture without looking at the viewfinder , light entering the eyepiece can throw off the exposure. T o prevent this, use the eyepiece cover (p.23) attached to the camera strap. During Live View shooting and movie shooting, attaching t he eyepiece cover is unnecessary .
113 Although using the self-timer or Re mote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups. When [ 8 C.Fn III -13: Mirror lockup] is set to [1: Enable] (p.
114 With Remote Controller RC-6, RC-1 or RC- 5 (sold separately), you can shoot remotely up to about 5 meters/16.4 feet from the camera. RC-6 or RC-1 enables you to shoot immediately or after a 2-sec. delay , and RC-5 has a 2-sec. delay . 1 Focus the subject.
115 In the d / s / f / a / F shooting modes, you can press the < D > button to pop-up and fire the built-in flash whenever desired. If the built-in flash has popped up, you can push it back down with your fingers. In the < 1 > (Full Auto) mode, the built-in flash fires automatically (p.
116 D Using the Built-in Flash Effective Range of Built-in Flash [Approx. meters/feet] Using the red-eye reduction lamp before taking a flash picture can reduce red eye. Under the [ 1 ] tab, select [ Red-eye On/Off ], then press < 0 >. Select [ On ], then press < 0 >.
117 D Using the Built-in Flash In the same way as normal exposure compensation, you can set exposure compensation for flash. Y ou can set flash exposure compensation up to ±3 stops in 1/3-stop increments. 1 Press the < m > button. ( 9 ) 2 Set the flash exposure compensation amount.
118 D Using the Built-in Flash FE (flash exposure) lock obtains and locks the correct flash exposure reading for any part of a subject. 1 Press the < D > button to pop-up the built-in flash. Press the shutter button halfway and look in the viewfinder to check that the < D > icon is lit.
119 The built-in flash and external S peedlite settings can be set with the menu. The [ External flash *** ] menu options for external S peedlites are applicable only to an attached EX-series S peedlite compatible with the respective functions . The setting procedure is the same as setting a camera menu function.
120 3 Setting the Flash N [Built-in flash func. setting] and [Ext ernal flash func. setting] Sett able Functions * Regarding the [ FEB ] (Flash exposure bracketing) and [ Zoom ], refer to the S peedlite’s instruction manual. Flash mode Y ou can select the flash mode to suit your desired flash shooting.
121 3 Setting the Flash N Shutter sync. Normally , set this to [ 1st curt ain ] so that the flash fires immediately after the exposure st arts. If [ 2nd curtain ] is set, the flash will fire right before the exposure ends. When this is combined with a slow sync speed, you can create a trail of light such as from car headlights at night.
122 3 Setting the Flash N 1 Display the Custom Function. Select [ External flash C.Fn setting ], then press < 0 >. 2 Set the Custom Function. T urn the < 5 > dial to select the function number , then set the function. The procedure is the same as setting the camera’s Custom Functions (p.
123 The camera’s built-in flash can work as a master unit with Canon S peedlites having a wireless slave feature and wirelessly trigger the S peedlite to fire. Be sure to read about wireless flash photography in the S peedlite’s instruction manual.
124 Using Wireless Flash N This shows the most basic setup for fully-automatic wireless flash with one S peedlite. Step s 1 to 3 and 6 to 8 apply to all wireless flash shooting. Therefore, these steps are omitted in the other wireless flash setups explained on the following pages.
125 Using Wireless Flash N 5 Select [Wireless func.]. For [ Wireless func. ], select [ 0 ], then press < 0 >. X Under [ Wireless func. ], [ Channel ], etc., will be displayed. 6 Set [Channel]. Set the channel (1-4) to the same one as the slave unit.
126 Using Wireless Flash N This shows fully-automatic wireless flash shooting with one external S peedlite and the built-in flash. Y ou can change the flash ratio between the external S peedlite and built-in flash to adjust how the shadows look on the subject.
127 Using Wireless Flash N Multiple S peedlite slave units can be treated as one flash unit or separated into slave groups whose flash ratio can be set. The basic settings are shown below . By changing the [ Firing group ] setting, you can shoot with various wir eless flash setups with multiple S peedlites.
128 Using Wireless Flash N [ 1 (A:B)] Multiple slave unit s in multiple groups Divide the slave units into groups A and B, and change the flash ratio to obtain the desired lighting effect.
129 Using Wireless Flash N [ 1 (A:B C)] Multiple slave unit s in multiple groups This is a variant of the [ 1 (A:B) ] setup on the preceding page. This setup has group C eliminate the shadows created by groups A and B.
130 Using Wireless Flash N The built-in flash can also be added to wireless flash shooting explained on pages 123-129. The basic settings are shown below . By changing the [ Firing group ] setting, you can shoot with various wir eless flash setups of multiple S peedlites complemented with the built-in flash.
131 Using Wireless Flash N Flash Exposure Compensation When [ Flash mode ] is set to [ E-TTL II ], flash exposure compensation can be set. The flash exposure compensation settings (see below) which can be set will differ depending on the [ Wireless func.
132 Using Wireless Flash N When [ Flash mode ] is set to [ Manual flash ], the flash output can be set manually . The flash output settings ([ 1 flash output ], [ Group A output ], etc.) that can be set wi ll differ depending on the [ Wireless func. ] setting (see below).
133 Basically operates like a built-in flash for easy operation. When an EX-series S peedlite (sold separately) is attached to the camera, almost all the autoflash cont rol is done by the camera. In other words, it is like a high-output flash attached externally in place of the built-in flash.
134 External Speedlites Sync Speed The camera can synchronize with non- Canon compact flash units at 1/ 250 sec. and slower speeds. With large studio flash units, since the flash duration is longer than compact flash units, set the sync speed within 1/60 sec.
135 Live View Shooting Y ou can shoot while viewing the picture on the camera’s LCD monitor . This is called “Live View shooting.” Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to < A >. Live View shooting is effective for still subject s which do not move.
136 1 Set the Live View shooting/Movie shooting switch to < A >. 2 Display the Live View image. Press the < 0 > button. X The Live View image will appear on the LCD monitor . The image’s field of view is about 100%. 3 Focus the subject. Before shooting, focus with AF or manual focus (p.
137 A Live View Shooting Battery Life with Live View Shooting [Approx. number of shot s] The figures above are based on a fully- charged Battery Pack LP-E6 and CIP A (Camera & Imaging Products As sociation) testing standards. Continuous Live View shooting is possib le for about 1 hr .
138 A Live View Shooting Each time you press the < B > button, the information display will change. About the Information Display Magnifying frame ISO speed Shots remaining Exposure level indica.
139 If you press the < m >, < o >,< n >, or < A > button during Live View shooting, the se tting screen will appear on the LCD monitor and you can turn the < 6 > or < 5 > dial to set the respective function. The < q > metering mode cannot be set.
140 Function settings particular to Live Vi ew shooting are explai ned here. The menu options under the [ z ] tab are explained below . The functions settable in this menu screen only apply during Live View shooting. These functions do not take effect during viewfinder shooting.
141 z Menu Function Settings Mode 1 The shooting operation noise is quieter than the normal shooting. Continuous shooting is also possible. High-speed continuous shooting will be approx. 7.0 fps. Mode 2 When you press the shutter button completely , only one shot will be taken.
142 The AF modes available are [ Live mode ], [ u Live mode ] (face detection, p.143), and [ Quick mode ] (p.147). If you want to achieve precise focus, set the lens focus mode switch to < MF >, magnify the image, and focus manually (p.149). Select the AF mode.
143 Using AF to Focus 3 Focus the subject. Aim the AF points over the subjects and press the shutter button halfway . X When focus is achi eved, the AF point will turn green a nd the beeper will sound. X If focus is not achieved, the AF point will turn red.
144 Using AF to Focus 2 Focus the subject. Press the shutter button halfway and the camera will focus the face covered by the < p > frame. X When focus is achieved , the AF point will turn green and the beeper will sound. X If focus is not achieved, the AF point will turn red.
145 Using AF to Focus AF operation Focusing will take slightly longer . Even when focus has been achieved , pressing the shutter button halfway will focus again.
146 Using AF to Focus Shooting conditions which can make focusing difficult: Low-contrast subjects such as the blue sky and solid-color , flat surfaces. Subjects in low light. S tripes and other patterns where there is contrast only in the horizontal direction.
147 Using AF to Focus The dedicated AF sensor is used to focus in the One-Shot AF mode (p.89), using the same AF me thod as with viewfinder shooting. Although you can focus the target area quickly , the Live View image will be interrupted momentar ily during the AF operation .
148 Using AF to Focus 3 Focus the subject. Aim the AF points over the subjects and press the shutter button halfway . X The Live View image will turn of f, the reflex mirror will go back down, and AF will be executed. X When focus is achieved, the beeper will sound and the Live View image will reappear .
149 Y ou can magnify the image and focus precisely manually . 1 Set the lens focus mode switch to <MF>. T urn the lens focusing ring to focus roughly . 2 Move the magnifying frame. Use < 9 > to move the magnifying frame to the position where you want to focus.
150 Live View Shooting Cautions Notes About the Live View Image Under low or bright light conditions, the Live View image might not reflect the brightness of the captured image. If the light source within the image changes, the screen might flicker . If this happens, stop and resume the Live View shooting under the actual light source to be used.
151 Live View Shooting Cautions Notes About the Shooting Results When you shoot continuous ly with the Live View function for a long period, the camera’s internal temp erature may increase and it can degrade image quality . T erminate Live View shooting when not shooting images.
152 C OP Y.
153 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to < k >. The movie file format will be MOV . When shooting movies, use a large-capacity card having a read/write speed of at least 8 MB/sec. If you use a slow card when shoo ting movies, the movie might not be recorded properly .
154 Connecting the camera to a TV set is recommended to playback movies (p.184-185). When the shooting mode is set to a shooting mode other than < a >, autoexposure control will take ef fect to fit the scene current brightness. Autoexposure control will be the same for all shooting modes.
155 k Shooting Movies Cautions for movie shooti ng are on pages 163-164. If necessary , also read the Live View shooting cautions on pages 150 and 151. Y ou can also focus by pressing the < p > button. One continuous movie will be recorded as one file.
156 k Shooting Movies Each time you press the < B > button, the information display will change. About the Information Display Magnifying frame AE lock ISO speed Shots remaining Exposure compens.
157 k Shooting Movies When the shooting mode is < a > (p.106), you can manually set the shutte r speeds, aperture, and ISO speeds shown below and shoo t a movie. Using manual exposure to shoot movies is for advanced users. Shutter speed : Turn the < 6 > dial.
158 k Shooting Movies Y ou can take a still photo at anytime by pressing the shutter button completely , even during movie shooting. T aking still photos du ring movie shooting The still photo will record the entire screen including the semi- transparent mask.
159 If you press the < o >, < n >, or < A > button while the image is displayed on the LCD monito r , the setting screen will appear on the LCD monitor and you can turn the < 6 > or < 5 > dial to set the respective function.
160 Function settings particular to movie shooting are explained here. When the Live View shooting/Movie shooting switch is set to < k >, the menu will show the [ x ] tab. The menu options are as follows. The AF mode will be the same as des cribed on pages 142-148.
161 x Menu Function Settings T otal Movie Recording Time and File Size Per Minute Movie-recording Size T otal Recording Time File Size 4 GB Card 16 GB Card [ 1920x1080 ] 6 12 min. 49 min. 330 MB/min. 5 4 [ 1280x720 ] 8 12 min. 49 min. 330 MB/min. 7 [ 640x480 ] 8 24 min.
162 x Menu Function Settings The built-in microphone records monaural sound. S tereo sound reco rding is possible by connecting an exter nal stereo microphone (commercially-availabl e) equipped with a miniature stereo plug (3.5 mm) to the camera’s external mi crophone IN terminal (p.
163 Notes on Movie Shooting Recording and Image Quality If the attached lens has an Image S tabilizer , the Image St abilizer will operate at all times even if you do not press th e shutter button halfway . The Image S tabilizer may cause the total movie shooting time or the number of possible shots to decrease .
164 Notes on Movie Shooting About the < E > icon and camera’ s internal temperature increase When you shoot movies continuously for a long period or in high temperatures, the camera’s internal temperature may increase and the < E > icon may appear on the screen.
165 Image Playback This chapter explains how to playback and erase photos and movies, how to display images on a TV screen, and other playback-related functions. About images taken with another camera: The camera might not be able to properly di splay images captured with a different camera or edited wi th a computer or whose file name was changed.
166 1 Playback the image. Press the < x > button. X The last captured image or last image viewed will appear . 2 Select the image. T o playback images starting with the last image, turn the < 5 > dial counterclockwise. T o playback images starting with the first captured image, turn the dial clockwise.
167 x Image Playback About the Highlight Alert When the [ 4 Highlight alert ] menu option is set to [ Enable ], overexposed highlight areas will blin k. T o obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again.
168 x Image Playback About the Histogram The brightness histogram display shows the exposure level distribution and overall brightness. The RGB histogram display is for checking the color saturation an d gradation. The display can be switched with the [ 4 Histogram ] menu option.
169 Search for images quickly with the index display showing four or nine images on one screen. 1 T urn on the index display . During image playback, press the < I > button. X The 4-image index display will appear . The currently-selected image will be highlighted in a blue frame.
170 x Searching for Images Quickly With the single image display , you can turn the < 6 > dial to jump through the images forward or backw ard according to the jump method set. 1 Select [Image jump w/ 6 ]. Under the [ 4 ] tab, select [ Image jump w/ 6 ], then press < 0 >.
171 Y ou can magnify the image by 1. 5x to 10x on the LCD monitor . 1 Magnify the image. During image playback, press the < u > button. X The image will be magnified. T o increase the magnification, hold down the < u > button. The image will continue to be magnified until it reaches the maximum magnification.
172 Y ou can rotate the displayed image to the desired orient ation. 1 Select [Rotate]. Under the [ 3 ] tab, select [ Rot ate ], then press < 0 >. 2 Select the image. T urn the < 5 > dial to select the image to be rotated. Y ou can also select an image on the index display .
173 Y ou can rate images and movies with one of five rating marks: l / m / n / o / p . This function is called rating. 1 Select [Rating]. Under the [ 3 ] tab, select [ Rating ], then press < 0 >. 2 Select an image or movie. T urn the < 5 > dial to select the image or movie to be rated.
174 3 Setting Ratings The total number of images with a given rating can be displayed up to 999. If there are more than 999 imag es with a given rating, [ ### ] will be displayed for that rating. T aking advantage of ratings With [ 4 Image jump w/ 6 ] menu, you can display only rated images and movies.
175 During playback, you can press the < Q > button to set the following: [ K : Protect images , b : Rotate image, 9 : Rating , S : Resize (JPEG image only), : Highlight alert , :AF point display , e : Image jump w/ 6 ]. For movies, only the function s in bold above can be set.
176 Q Quick Control During Playback T o rotate an image, set [ 5 Auto rotate ] menu to [ On z D ]. If [ 5 Auto rotate ] menu is set to [ On D ] or [ Off ], the [ b Rot ate image ] setting will be recorded to the imag e, but the camera will not rotate the image for displ ay .
177 Basically , there are the following thr ee ways to playback the movies you shot. Use the provided A V cable or an HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Then you can playback the captured movies and photos on the TV .
178 k Enjoying Movies The movie files recorded on the card can be transferred to a personal computer and played with ImageBrowser EX (provided software). Playback and Editing with a Personal Computer (p.282) T o have the movie play back smooth ly on a personal computer , use a high-performance personal computer .
179 1 Playback the image. Press the < x > button to display the image. 2 Select a movie. T urn the < 5 > dial to select the image. During the single-image display , the < 1s > icon displayed on the upper left indicates that it is a movie.
180 k Playing Movies Function Playback Description Exit Returns to the single-image display . 7 Play Pressing < 0 > toggles between play and pause. 8 Slow motion Adjust the slow motion speed by turning the < 5 > dial. The slow-motion speed is indi cated on the upper right.
181 Y ou can edit out the first and last scenes of a movie in 1-sec. increments. 1 On the movie playback screen, select [ X ]. X The editing screen will be displayed. 2 Specify the p art s to be edited out. Select either [ ] (Cut beginning) or [ ] (Cut end), then press < 0 >.
182 Y ou can playback the images in the card as an automatic slide show . 1 Select [Slide show]. Under the [ 4 ] tab, select [ Slide show ], then press < 0 >. 2 Select the images to be played back. T urn the < 5 > dial to select the item, then press < 0 >.
183 3 Slide Show (Auto Playback) 3 Set the play time and repeat option. Tu rn t h e < 5 > dial to select [ Set up ], then press < 0 >. For still photos, set the [ Play time ] and [ Repeat ] options, then press the < M > button. 4 St art the slide show .
184 Y ou can also view the still photos and movies on a TV set. Before connecting or disconnecting the cable between the camera and television, turn off the camera and television. * Adjust the movie’s sound volume with the TV set. * Depending on the TV se t, part of the image di splayed might be cut off.
185 Viewing the Images on TV The HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HD MI cable to the cam era. Connect the HDMI cable to the camera’s < D > terminal. With the plug’s < d HDMI MINI > logo facing the front of the camera, insert it into the < D > terminal.
186 Protecting the image prevents it from being erased accidentally . 1 Select [Protect images]. Under the [ 3 ] tab, select [ Protect images ], then press < 0 >. X The protect setting screen will appear . 2 Select the image and protect it. T urn the < 5 > dial to select the image to be protected, then press < 0 >.
187 Y ou can either select and erase images one by one or erase them in one batch. Protected images (p.186) will not be erased. Once an image is erased, it cann ot be recovered. Make sure you no longer need the image before erasing it. T o prevent important images from being erased accident ally , protect it.
188 L Erasing Images 2 Select [Select and erase images]. T urn the < 5 > dial to select [ Select and erase images ], then press < 0 >. X The image will be displayed. T o display the three-image view , press the < I > button. T o return to the single-image display , press the < u > button.
189 The LCD monitor ’s brightness is ad justed automatically for optimum viewing. Y ou can set the automatic adjustment’s brightness level (brighter or darker) or adjust the brightness manually . 1 Select [LCD brightness]. Under the [ 6 ] tab, select [ LCD brightness ], then press < 0 >.
190 Changing Image Playback Settings V ertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and computer instead of horizontally . The setting of this feature can be changed. 1 Select [Auto rot ate]. Under the [ 5 ] tab, select [ Auto rota te ], then press < 0 >.
191 Post-Processing Images Y ou can process RAW images with the camera or resize (shrink) JPEG images. A M icon at the upper right of a p age title indicates that the function can be used when the Mode Dial is set to < d / s / f / a / F >. * Function which cannot be used in the fully-automatic modes ( 1 / C ).
192 Y ou can process 1 images with the camera and save them as JPEG images. While the RA W image itself does not change, you can process the RA W image according to different conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera.
193 R Processing RAW Images with the Camera N Displaying the setting screen Press < 0 > to display the setting screen. T urn the < 5 > or < 6 > dial to change the setting. T o return to the screen in step 3, press < 0 >. 4 Save the image.
194 R Processing RAW Images with the Camera N White balance (p.72) Y ou can select the white balance. If you select [ P ], turn the < 6 > dial to set the color temperature on the setting screen. The displayed image will reflect the setting’s ef fect.
195 R Processing RAW Images with the Camera N Color space (p.86) Y ou can select either sRGB or A dobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.
196 R Processing RAW Images with the Camera N Chromatic aberration correction When [ Enable ] is set, lateral chromatic aberration caused by the lens (color fringing along the subject’s outline) can be corrected. If [ Enable ] is set, the corrected image will be displayed.
197 Y ou can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3 / 4 images. JPEG 6 and RA W images cannot be resized. 1 Select [Resize]. Under the [ 3 ] tab, select [ Resize ], then press < 0 >.
198 S Resize Resize Options According to Original Image Size Original Image Size A vailable Resize Settings 4 6 3 kk 4 k C OP Y.
199 Sensor Cleaning The camera has a Self Cleani ng Sensor Unit attached to the image sensor ’s front layer (low-pass filter) to shake off dust automatically . The Dust Delete Data can also be appended to the image so that the dust spot s remaining can be erased automatically by Digital Photo Professional (provided software).
200 Whenever you set the power switch to < 1 > or < 2 >, the Self Cleaning Sensor Unit operates to aut omatically shake off the dust on the front of the sensor . Normally , you need not pay attention to this operation. However , you can execute the sensor cleaning at anytime as well as disable it.
201 Normally , the Self Cleaning Sensor Un it will eliminate most of the dust that might be visible on captured im ages. However , in case visible dust still remains, you can append the Dust Delete Data to the image to later erase the dust spots.
202 3 Appending Dust Delete Data N 3 Photograph a solid-white object. At a distance of 20 cm - 30 cm / 0.7 ft. - 1.0 ft., fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in the aperture-priority AE mode with an aperture of f/22.
203 Dust which could not be removed by the automatic sensor cleaning can be removed manually with a blower , etc. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly , having it done by a Canon Service Center is recommended.
204 3 Manual Sensor Cleaning N While cleaning the sensor , never do any of the following. Doing any of the following will cut off the power and close the shutter . The shutter curtains and image sensor might get damaged. • Setting the power switch to < 2 >.
205 Printing Images Printing (p.206) Y ou can connect the camera directly to a printer and print out the images in the card. The camera is compatible with “ w PictBridge” which is the standard for direct printing. Digital Print Order Format (DPOF) (p.
206 The direct printing procedure is done entirely with the camera while you look at the LCD monitor . 1 Set the camera’ s power switch to < 2 >. 2 Set up the printer . For details, see the printer’s instruction manual. 3 Connect the camera to the printer .
207 Preparing to Print 6 Playback the image. Press the < x > button. X The image will appear , and the < w > icon will appear on the upper left to indicate that the camera is connected to a printer . w PictBridge Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct.
208 The screen display and setting options will differ depending on the printer . Some settings might not be available. For details, see the printer ’s instruction manual. 1 Select the image to be printed. Check that the < w > icon is displayed on the upper left of the LCD monitor .
209 w Printing Select the size of the paper loaded in the printer , then press < 0 >. X The paper type screen will appear . Select the type of the paper loaded in the printer , then press < 0 >. When using a Canon printer and Canon paper , read the printer ’s instruction manual to check what paper types can be used.
210 w Printing 4 Set the printing effects. Set as necessary . If you need not set any printing effects, go to step 5. The screen display may differ depending on the printer . Select the option on the upper right (circled in the screenshot), then press < 0 >.
211 w Printing 5 Set the date and file number imprinting. Set as necessary . Select < I >, then press < 0 >. Set as desired, then press < 0 >. 6 Set the number of copies. Set as necessary . Select < R >, then press < 0 >.
212 w Printing In step 4 on page 210, select the printing effect. When the < e > icon is displayed next to < z >, press the < B > button. Y ou can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4.
213 w Printing Y ou can crop the image and print only the trimmed portion as if the image was recomposed. Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 On the print setting screen, select [T rimming].
214 w Printing Depending on the printer , the trimmed image area might not be printed as you specified. The smaller you make the trimming fr ame, the grainier the picture will look on the print. While trimming the image, look at th e camera’s LCD monitor .
215 Y ou can set the print type, date impr inting, and file No. imprinting. The print settings will be applied to al l print-ordered images. (They cannot be set individually for each image.) 1 Select [Print order]. X Under the [ 3 ] tab, select [ Print order ], then press < 0 >.
216 W Digital Print Order Format (DPOF) 4 Exit the setting. Press the < M > button. X The print order screen will reappear . Next, select [ Sel.Image ], [ By n ], or [ All image ] to order the images to be printed. Print type K S tandard Prints one image on one sheet.
217 W Digital Print Order Format (DPOF) Sel.Image Select and order images one by one. T o display the three-image view , press the < I > button. T o return to the single-image view , press the < u > button. After completing the print order , press the < M > button to save the print order to the card.
218 With a PictBridge printer , you can easily print images with DPOF . 1 Prep aring to print. See page 206. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [ 3 ] t ab, select [Print order]. 3 Select [Print]. [ Print ] will be displayed only if the camera is connected to the printer and printing is possible.
219 Customizing the Camera With Custom Functions, yo u can change the camera functions to suit your pref erences. Also, the current camera settings can be saved under the Mode Dial’s < w >, < x >, and < y > positions.
220 1 Select [ 8 ]. T urn the < 6 > dial to select the [ 8 ] tab. 2 Select the group. T urn the < 5 > dial to select C.Fn I - IV , then press < 0 >. 3 Select the Custom Function number . T urn the < 5 > dial to select the Custom Function No.
221 3 Custom Functions N C.Fn I: Exposure A LV shooting k Movie shooting 1 Exposure level increments p.222 k 2 ISO speed setting increments kk (< a >) 3 ISO expansion k 4 Bracketing auto cancel k 5 Bracketing sequence p.223 k 6 Safety shift k 7 Flash sync.
222 3 Custom Function Settings N C.Fn I: Exposure C.Fn I -1 Exposure level increment s 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. Effective when you prefer to control the exposure in less fine increments than 1/3-stop increments.
223 3 Custom Function Settings N C.Fn I -5 Bracketing sequence The AEB shooting sequence and white bal ance bracketing sequence can be changed. 0: 0, -, + 1: -, 0, + C.Fn I -6 Safety shif t 0: Disable 1: Enable (Tv/A v) This works in the s hutter-priority AE ( s ) and aperture-priority AE ( f ) modes.
224 3 Custom Function Settings N C.Fn II: Image C.Fn II -1 Long ex posure noise reduction 0: Off 1: Auto For 1 sec. or longer exposure s, noise reduction is performed automatically if noise typical of long exposures is detected. This [ Auto ] setting is effective in most cases.
225 3 Custom Function Settings N C.Fn II -3 Highlight tone priority 0: Disable 1: Enable Improves the highlight detail. The dynamic range is expanded between the standard 18% gray and bright highl ight s. The gradation between the grays and highlights becomes smoother .
226 3 Custom Function Settings N C.Fn III -2 AI Servo 1st/2nd image priority For the AI Servo AF and continuous shooting modes, you can change the Servo’s operation characteristics and shutter-release timing. 0: AF priority/T racking priority For the first shot, focusing the subj ect is given priority .
227 3 Custom Function Settings N C.Fn III -4 Lens drive when AF impossible If autofocus is executed, but focus cannot be achieved, the camera can either keep trying to focus or stop. 0: Focus search on 1: Focus search off Prevents the camera from becoming grossly out of focus as it attempts to focus again.
228 3 Custom Function Settings N C.Fn III -6 Select AF area selection mode Make the mode selectable by selecting [ Register ], then pressing < 0 >. T urn the < 5 > dial to select the mode to be used, then press < 0 > to append a < X > checkmark.
229 3 Custom Function Settings N C.Fn III -8 VF display illumination The AF points, grid, etc., in the vi ewfinder can be illuminated in red. 0: Auto The viewfinder illumination turns on automatically under low light. 1: Enable The viewfinder illumination turns on regardless of the ambient light level.
230 3 Custom Function Settings N C.Fn III -1 1 AF-assist beam firing The AF-assist beam can be emitted by t he camera’s built-in flash or by an external, EOS-dedicated S peedlite.
231 3 Custom Function Settings N C.Fn III -13 Mirror lockup 0: Disable 1: Enable Prevents camera vibrations caused by the reflex mirror action that can disturb shooting with s uper telephoto lenses or close-up (macro) shooting. See page 1 13 for the mirror lockup procedure.
232 3 Custom Function Settings N C.Fn IV -3 Add image verification data 0: Disable 1: Enable Data for verifying whether the image is original or not is appended to the image automatically . When the shooting information of an image appended with the verification data is displayed (p.
233 3 Custom Function Settings N 1 Select [ 8 C.Fn IV -1: Custom Controls]. A list of camera controls and their assigned functions will appear (p.234). When you press < 0 >, the camera controls setting screen will appear . 2 Select the camera button or dial.
234 3 Custom Function Settings N * The AF stop button is provided on ly on super telephoto IS lenses. Assignable Functions to Camera Controls Function Page * Metering and AF start 235 k k * 1 k * 1 k .
235 3 Custom Function Settings N < > Metering and AF st art When you press the button assigned with this function, metering and AF are executed. *1: If you assign the [ Metering and AF st art ] .
236 3 Custom Function Settings N < > ONE SHOT z AI SERVO In One-Shot AF mode, when you hold down the button to which this function has been assigned, the ca mera switches to AI Se rvo AF mode. And in the AI Servo AF mode, the camera switc hes to One-Shot AF mode only while you hold down the button.
237 3 Custom Function Settings N < > Picture Style Press < 0 > to display the Picture S tyle selection screen (p.66) on the LCD monitor . < > Image replay T o playback images, press < 0 >. < > Depth-of-field preview Pressing the depth-of-field preview bu tton will stop down the aperture.
238 Under the My Menu tab, you can regi ster up to six menu options and Custom Functions whose settings you change frequently . 1 Select [My Menu settings]. Under the [ 9 ] tab, select [ My Menu settings ], then press < 0 >. 2 Select [Register].
239 Under the Mode Dial’s < w >, < x >, and < y > positions, you can register most of the current camera settings including your preferred shooting mode, menus, Custom Function settings, etc. 1 Select [Camera user setting]. Under the [ 7 ] tab, select [ Camera user setting ], then press < 0 >.
240 w Register Camera User Settings N Shooting functions Shooting mode + setting, ISO speed, AF mode, AF point, Metering mode, Drive mode, Exposure compensation amount, Flash exposure compensation amo.
241 When you set the copyright info rmation, it will be appended to the image as Exif information. 1 Select [Copyright information]. Under the [ 7 ] tab, select [ Copyright information ], then press < 0 >. 2 Select the desired option. Select [ Display copyright info.
242 3 Setting Copyright Information N Changing the entry area Press the < A > button to toggle between the top and bottom entry areas. Moving the cursor T urn the < 5 > dial to move the cursor . Y ou can also use < 9 > to move the cursor .
243 Reference This chapter provides refere nce information for camera features, system accessories, etc. The back of this chapter also has an index to make it easier to look up needed information.
244 When you press the < B > button while the camera is ready to shoot, you can display [ Displays camera settings ], [ Displays shooting functions ] (p.245), and [ Electronic level ] (p.50). Under the [ 7 ] tab, the [ INFO. button display options ] option enables you to select what the < B > button is to display when pressed.
245 B Button Functions * If flash exposure compensation is set with an external S peedlite, the flash exposure compensation ic on will change from < y > to < C >. When you press the < Q > button, the Quick Control screen appears (p.38).
246 Y ou can check the battery’s conditi on on the LCD monitor . A Battery Pack LP-E6 has a unique serial No., and you can register multiple battery packs to the camera. When you use this feature, you can check the registered battery pack’s remain ing cap acity and operation history .
247 3 Checking the Battery Information Y ou can register up to six Battery Pack LP-E6’s to the camera. T o register multiple battery packs to the camera, do the procedure below for each battery pack. 1 Press the < B > button. With the Battery info.
248 3 Checking the Battery Information Affixing the serial No. onto all t he registered Battery Pack LP-E6’s with a label makes it convenient. 1 Write the serial No. on a label. Write the serial No. displayed on the battery history screen on a label about 25 mm x 15 mm / 1.
249 3 Checking the Battery Information Y ou can check the remaining capacity of any battery p ack (even while not installed) and also when it was last used. Look for the serial No. Refer to the battery’s serial No. label and look for the batte ry’s serial No.
250 With the AC Adapter Kit ACK-E6 (s old separately), you can connect the camera to a household power outle t and not worry about the battery level. 1 Connect the DC Coupler ’ s plug. Connect the DC Coupl er ’s plug to the AC Adapter's socket.
251 The date/time (back-up) battery maintains the camera’ s date and time. Its service life is about 5 years. If you turn on the power and the date/ time is reset, replace the back-up battery with a new CR1616 lithium battery as described below . The date/time/zone setting will be reset, so be sure to set the correct date/time/zone (p.
252 System Map Wide Strap EW-EOS7D Bundled Accessories Eyecup Eg Anti-Fog Eyepiece Eg Dioptric Adjustment Lenses Eg Angle Finder C Date / time CR1616 lithium battery Battery Pack LP-E6 Battery Charger.
253 System Map EF-S lenses EF lenses Stereo A V Cable A VC-DC400ST Timer Remote Controller TC-80N3 Remote Switch RS-80N3 Wireless Controller LC-5 HDMI Cable HTC-100 External microphone Interface Cable.
254 o : Set automatically k : User selectable : Not selectable Function Availability Table Mode Dial 1 C d s f a F Quality JPEG kkkkkkk RAW kkkkkkk RAW+JPEG kkkkkkk ISO speed Auto o o k k k k k Manual.
255 Function Availability Table o : Set automatically k : User selectable : Not selectable *1: Refers to “(2) Blurring/sharpenin g the background” fu nction on page 56.
256 1 Shooting 1 (Red) Page 2 Shooting 2 (Red) Menu Settings Quality 73 / 83 / 74 / 84 / 76 / 86 60 1 / 41 / 61 Red-eye On/Off Off / On 11 6 Beep On / Off – Release shutter without card Enable / Disable 29 Review time Off / 2 sec.
257 Menu Settings y Shooting 3 (Red) Page z Shooting 4 (Red) * For movie shooting, see page 260. 3 Playback 1 (Blue) Dust Delete Data Obtains data to be used to erase dust spots 201 One-touch RA W+JPEG Also capture RA W or JPEG when necessary 63 ISO Auto Max.
258 Menu Settings 4 Playback 2 (Blue) Page 5 Set-up 1 (Y ellow) Highlight alert Disable / Enable 167 AF point display Disable / Enable 168 Histogram Brightness / RGB 168 Slide show Select the images a.
259 Menu Settings 6 Set-up 2 (Y ellow) Page 7 Set-up 3 (Y ellow) LCD brightness Auto: Adjustable to one of three brightness levels Manual: Adjustable to one of seven brightness levels 189 Date/Time/Zone Date (year , month, day) / Time (hour , min., sec.
260 Menu Settings 8 Custom Functions (Orange) Page 9 My Menu (Green) x Movie (Red) Page * In the < 1 / C > mode, it will be [ Sound recording ]: [ On/Off ]. C.Fn I : Exposure Customize camera functions as desired 222 C.Fn II : Image 224 C.Fn III : Autofo cus/ Drive 225 C.
261 If a problem occurs, first refer to this T roubleshooting Guide. If this T roubleshooting Guide do es not resolve the problem, contact your dealer or nearest Canon Service Center . If the battery’s remaining capacity (p.246) is 94% or higher , the battery will not be recharged.
262 Troubleshooting Guide If the power is cut off while an image is being recorded to the card, the access lamp will still continue to light/blink for a few seconds. When the image recording is comp leted, the power will turn off automatically . Use a fully-charged battery (p.
263 Troubleshooting Guide Set the lens focus mode switch to < AF > (p.31). T o prevent camera shake, hold the camera still and press the shutter button gently (p.34, 35). If the lens has an Image S tabilizer , set the IS switch to < 1 >. If a card error me ssage is displayed, see page 30 or 267.
264 Troubleshooting Guide Make sure the external flash (or PC sync cord) is securely attached to the camera. If you use a non-Canon flash with Live View shooting, set the [ z Silent shoot. ] menu to [ Disable ] (p.141). The built-in flash’s pop-up mechanism moves slightly .
265 Troubleshooting Guide If you operate the camera’s dial or lens during movie shooting, the respective operation noise will al so be recorded. Use an external microphone (commercially available) (p.
266 Troubleshooting Guide If you use a card which already has images recorded, the file numbering might start from the la st image in the card (p.84). The correct date and time has not been set (p.43). Check the time zone and daylight savings time (p.
267 If there is a problem with the camera, an error message will appear . Follow the on- screen instructions. * If the error still persists, write down the error No. and cont act your nearest Canon Service Center . Error Codes No. Error Message & Solution 01 Communications between the camera and lens is faulty .
268 •T y p e Ty p e : Digital, single-lens reflex, AF/AE camera with built-in flash Recording media: T ype I or II CF card, UDMA-compatible Image sensor size : 22.3 x 14.9 mm Compatible lenses: Canon EF le nses (including EF-S lenses) (35mm-equivalent focal length is appr ox.
269 Specifications • Viewfinder T ype: Eye-level pentaprism Coverage: V ertical/Hor izontal approx. 100% Magnification: Appr ox. 1.0x (-1 m -1 with 50mm lens at infinity) Eye point: Approx. 22 mm (From ey epiece lens ce nter at -1m -1 ) Built-in dioptric adjustment : -3.
270 Specifications •S h u t t e r T ype: Electronically-contro lled, focal-plane shutter Shutter speeds: 1/8000 sec. to 1/60 se c. (Full Auto mode), X-sync at 1/ 250 sec. 1/8000 sec. to 30 sec., bulb (T otal shutter speed range. Available range varies by shooting mode.
271 Specifications • Movie Shooting Movie compression: MPEG-4 A VC V ariable (average) bit rate Audio recording format: Linear PCM File type: MOV Recording size and frame rate: 1920x108 0 (Full HD) : 30p/25p/24p 1280x720 (HD) : 60p/50p 640x480 (SD) : 60p/50p * 30p: 29.
272 Specifications Zoom magnification: Approx. 1.5x - 10x Image browsing methods : Single image, jump by 10 or 100 images, by shooting date, by folder , by movies, by stills, by rating Ratings: Provid.
273 Specifications Battery information: Remaining capa city , Shutter count, and Recharge performance displayed Battery life: With viewfinder shooting: (Based on CIP A Approx. 800 shots at 23°C/73°F , approx. 750 shots at 0°C/32°F testing standards) With Live View shooting: Approx.
274 Specifications Working temperature range :5 ° C - 40 ° C / 41 ° F - 104 ° F Working humidity: 85% or less Dimensions (W x H x D) : 69 x 33 x 93 mm / 2.7 x 1.3 x 3.7 in. Weight: Approx. 125 g / 4.4 oz . (excluding power cord) • EF-S15-85mm f/3.
275 Specifications • EF28-135mm f/3.5-5.6 IS USM Angle of view: Diagona l extent: 75° - 18° Horizontal extent: 65° - 15° V ertical extent: 46° - 10° Lens construction: 16 el ements in 12 groups Minimum aperture: f/22 - 36 Closest focusing distance : 0.
276 About MPEG-4 Licensing “This product is licensed under A T&T pate nts for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that .
277 Safety Warnings Follow these safe guards and use the eq uipment properly to pr event injury , death, and material damage. Preventing Serious Injury or Death • T o prevent fire, excessive heat, c.
278 • If you drop the equipment and the casing br eaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassem ble or modify the equipment. High-voltage internal p arts can cause electrical shock.
279 Digital Camera Model DS126251 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) This device may not ca use harmful interference, and (2) this device mu st accept any interference received, including interference that may ca use undesired operation.
280 IMPORT ANT SAFETY INSTRUCTIONS 1. SA VE THESE INSTRUCTIONS — This manual contai ns important safety and operating instructions for Battery Charger LC-E6 & LC-E6E. 2. Before using the charger, read all in structi ons and cautionary remarks on (1) the charger , (2) the ba ttery pack, and (3) the pro duct using the battery pack.
281 Software Start Guide This chapter gives an overvi ew of the software in the EOS DIGIT AL Solution Disk (CD-ROM) provided with the camera and explains how to install the software on a personal computer . It also ex plains how to view the PDF files in the Software In struction Manual CD-ROM.
282 EOS DIGITAL Solution Disk This disk contains various software for EOS DIGIT AL cameras. With the camera connected to a personal computer , EOS Utility enables you to transfer still phot os and movies shot with the camera to the computer .
283 Software Start Guide 1 Insert EOS DIGIT AL So lution Disk (CD-ROM). For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [ Canon EOS Digital Installer ]. 2 Click [Easy Installation] and follow the on-screen instructions to inst all.
284 Software Start Guide Software Instruction Manual Contains the Sof tware Instruction Manuals. 1 Insert the [Sof tware INSTRUCTION MANUAL] CD-ROM into your computer . 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [ (My) Computer ].
285 Index 10-sec. or 2-sec. delay.................... 98 1280x720 ................. .....................160 1920x1080 ........... .........................160 19-point AF auto selection ........91, 94 1st-curtain sync .... ......................... 121 2nd-curtain sync.
286 Index Cleaning................. ....................... 199 Clear camera settings ..................... 47 Color space....... ................. ............. 86 Color temperature . ............. ............. 74 Color tone ......... ..............
287 Index Focusing AF area ......................... 91, 93, 228 AF characteristics . 225, 226, 227, 235 AF mode .................. ... 88, 236, 245 AF point display ........................ 229 AF point registration ......... 230, 235 AF point selection .
288 Index Jump display .......... ....................... 170 L Landscape ............. ......................... 66 Language selection......................... 42 Large (Image-recordi ng quality)...... 61 LCD monitor...... ................. .........
289 Index N Neutral ................. ................. ..........67 Noise reduction High ISO speed ........................224 Long exposures ........................ 224 Nomenclature........................ ..........16 Non-Canon flash un its ......
290 Index Saturation ......... ................. ............. 68 Self-timer .......... ................. ............. 98 Sensor cleaning ............................ 199 Sepia (Monochrome) ...................... 69 Sharpness.............. ..........
291 MEMO C OP Y.
CPH-E034-000 © CANON INC. 2012 The lenses and accessories mentioned in this Instruction Manual are current as of June 2012. For information on the camera’s compatibility with any lenses and accessories introduced after this date, contact any Canon Service Center .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Canon 7D c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Canon 7D - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Canon 7D, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Canon 7D va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Canon 7D, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Canon 7D.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Canon 7D. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Canon 7D ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
