

residential type environments.

from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose.


1 Top spray arm 2 Upper spray arm 3 Lower spray arm 4 Filters 5 Rating plate 6 Salt container 7 Air vent
8 Rinse aid dispenser 9 Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket

1 On/off button 2 Programme buttons 3 Delay button

End indicator.
XtraDry indicator.
Salt indicator. It is always off while the programme operates.
Rinse aid indicator. It is always off while the programme operates.
Programme Degree of soil Type of load
225 0.932 10.2
Normal soil Crockery and cutlery
30 0.9 10
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 2) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 3) This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the temperature stays at 70 ° for at least 10 minutes. 4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time. 5) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance. Do not use detergent with this programme.

Write down the product number (PNC) that is on the rating plate.
For all the necessary information for test performance, send an email to:
info.test@dishwasher-production.com
When you activate the appliance, usually it is in programme selection mode. However, if this does not happen, you can set the programme selection mode in the following way:
When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode.
Press and hold simultaneously and until the appliance is in programme selection mode.
The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance.
The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
These settings will be saved until you change them again.
The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results.
The appliance is in programme selection mode when only the indicator of the programme is on.

If you use multi-tablets containing salt and the hardness of your water is lower than 21dH, you can set the lowest water softener level. It deactivates the salt refill indicator.
The rinse aid helps to dry the dishes without streaks and stains.
The rinse aid is automatically released during the hot rinse phase.
If you use standard detergent or multi- tablets without salt, set the proper water hardness level to keep the salt refill indicator active.
You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 will deactivate the rinse aid dispenser and no rinse aid will be released.
Factory setting: level 4.
The appliance must be in programme selection mode.
The appliance must be in programme selection mode.
– E.g. 5 flashes + pause + 5
flashes = level 5. 3. Press again and again to change the setting. Each time you press the level number increases. After level 10 you will start again from level 1. 4. Press the on/off button to confirm the setting.
– The levels of rinse aid are from 0
to 6. – Level 0 = no rinse aid is
released. In this case the end indicator remains off. 3. Press again and again to change the setting. Each time you press the

level increases. After level 6 you go to level 0 and then start again from level 1. 4. Press the on/off button to confirm the setting.
Acoustic signals
When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If you are using multi-tabs containing rinse aid and you are satisfied with the drying result, you can deactivate the notification for refilling rinse aid. However, we recommend that you always use rinse aid for best drying performance.
Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals.
There is also an acoustic signal that sounds when the programme is completed. By default this acoustic signal is deactivated but it is possible to activate it.
If you use standard detergent or multi- tablets without rinse aid, activate the notification to keep the rinse aid refill indicator active.
The appliance must be in programme selection mode.
The appliance must be in programme selection mode.
Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running.
Activate this option when you want to boost the drying performance. With the use of this option, the duration of some programmes, water consumption and the last rinse temperature can be affected.
The option XtraDry is not a permanent option and must be selected at every cycle.

Press and hold simultaneously and until the indicator comes on.

1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically. How to fill the salt container
Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme.



Fill the rinse aid dispenser when the indicator (A) becomes clear.
If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled. We recommend to always use rinse aid for better drying performance, also in combination with multi-tablets containing rinsing agent.
The AUTO OFF function
This function decreases energy consumption by deactivating automatically the appliance when it is not operating.

Cancelling the delay start while the countdown operates
When you cancel the delay start you have to set the programme and options again.
Press and hold simultaneously and until the appliance is in programme selection mode.
Press and hold simultaneously and until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme.
End of programme
If you open the door while a programme is running, the appliance stops. It may affect the energy consumption and the programme duration. When you close the door, the appliance continues from the point of interruption.
When the programme is completed and you open the door, the appliance is automatically deactivated.
Close the water tap.
If the door is opened for more than 30 seconds during the drying phase, the running programme will end.
The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment.

Make sure that:
Before you start to use separately detergent, salt and rinse aid do the following procedure.
At the end of the programme water can still remain on the sides and on the door of the appliance.


Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them.
The filter system is made of 3 parts.






We recommend to clean regularly the upper spray arm to avoid soil to clog the holes.

Clogged holes can cause unsatisfactory washing results.


use monthly a specific cleaning product for dishwashers. Follow carefully the
instructions on the packaging of the product.
If the appliance does not start or it stops during operation, before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table.
With some problems the end indicator flashes intermittently indicating a malfunction.
The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
Problem and alarm code Possible cause and solution

Problem and alarm code Possible cause and solution
The appliance stops and starts more times during operation.
The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown.
Rattling/knocking sounds from inside the appliance.
problem occurs again, contact an Authorised Service Centre.
Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes.
For alarm codes not described in the table, contact an Authorised Service Centre.
Once you have checked the appliance, deactivate and activate the appliance. If the
Problem Possible cause and solution

Problem Possible cause and solution
There are whitish streaks or bluish layers on glasses and dishes.
There are stains and dry water drops on glasses and dishes.
The interior of the appliance is wet.
There are residues of detergent in the dispenser at the end of the programme.
Odours inside the appliance. • Refer to "Internal cleaning".

Problem Possible cause and solution
Limescale deposits on the ta- bleware, on the tub and on the inside of the door.
Dull, discoloured or chipped ta- bleware.
Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes.
Dimensions Width / height / depth (mm) 596 / 818-898 / 550
Electrical connection 1) Voltage (V) 200 - 240
Frequency (Hz) 50 / 60
Water supply pressure bar (minimum and maximum) 0.5 - 8
MPa (minimum and maximum) 0.05 - 0.8
Water supply Cold water or hot water 2) max 60 °C
Capacity Place settings 13
Power consumption Left-on mode (W) 0.99
Power consumption Off-mode (W) 0.10
dispose appliances marked with the symbol
Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not
with the household waste. Return the product to your local recycling facility or contact your municipal office.
Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| You cannot activate the appliance. | • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. | p.15 | |
| The programme does not start. | • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to re- charge the resin inside the water softener. The duration of the procedure is approximately 5 mi- nutes. | p.15 | |
| The appliance does not fill with water. • The end indicator flashes 1 time in- termittently. • Acoustic signal sounds 1 time inter- mittently. | • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. | p.15 | |
| The appliance does not drain the water. • The end indicator flashes 2 times in- termittently. • Acoustic signal sounds 2 times inter- mittently. | • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. | p.15 | |
| The anti-flood device is on. • The end indicator flashes 3 times in- termittently. • Acoustic signal sounds 3 times inter- mittently. | • Close the water tap and contact an Authorised Service Centre. | p.16 | |
| The appliance stops and starts more times during operation. | • It is normal. It provides optimal cleaning results and energy savings. | p.16 | |
| The program lasts too long. | • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. | p.16 | |
| Small leak from the appliance door. | • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Ad- just the rear foot (if applicable). | p.16 | |
| The appliance door is difficult to close. | • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets. | p.16 | |
| Rattling/knocking sounds from inside the appliance. | • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. | p.16 | |
| The appliance trips the circuit-beaker. | • The amperage is insufficient to supply simultane- ously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. | p.16 | |
| Poor washing results. | • Refer to "Daily use", "Hints and tips" and basket load- ing leaflet. • Use more intensive washing programmes. | p.16 | |
| Poor drying results. | • Tableware has been left for too long inside a closed appli- ance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option Xtra- Dry. • We recommend to always use rinse aid, even in combina- tion with multi-tablets. | p.17 | |
| There are whitish streaks or bluish layers on glasses and dishes. | • The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level. • The quantity of detergent is too much. | p.17 | |
| There are stains and dry water drops on glasses and dishes. | • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. | p.17 | |
| The dishes are wet. | • For the best drying performance activate the option Xtra- Dry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a dif- ferent brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. | p.17 | |
| The interior of the appliance is wet. | • This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls. | p.17 | |
| Unusual foam during washing. | • Use the detergent for dishwashers only. • There is a leak in the rinse aid dispenser. Contact an Au- thorised Service Centre. | p.17 | |
| Traces of rust on cutlery. | • There is too much salt in the water used for washing. Re- fer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. | p.17 | |
| There are residues of detergent in the dispenser at the end of the programme. | • The detergent tablet got stuck in the dispenser and there- fore was not completely washed away by water. • Water cannot wash away the detergent from the dispens- er. Make sure that the spray arm is not blocked or clog- ged. • Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. | p.17 | |
| Odours inside the appliance. | • Refer to "Internal cleaning". | p.17 | |
| Limescale deposits on the ta- bleware, on the tub and on the inside of the door. | • Refer to "The water softener". | p.18 | |
| Dull, discoloured or chipped ta- bleware. | • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. | p.18 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.