Manuel d'utilisation / d'entretien du produit G 7883 CD du fabricant Miele
Aller à la page of 76
Operating and Installation Instructions Laboratory Glassware Washer G 7883 CD To prevent accidents and machine damage read these instructions before installation or use.
2.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Guide to the lab washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Description of the machine . . . . . . .
Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions: .
This machine conforms to current safety requirements. However, inappropriate use can lead to personal injury and property damage. Read the operating instructions carefully before using this machine. The manufacturer cannot be held responsible for damage caused by non-observance of these Important Safety Instructions.
~ Take care when handling processing chemicals (detergents, softeners, neutralizers, etc.). These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed.
The following points should be observed to assist in maintaining quality standards for critical labware and to avoid damage to the loads being cleaned. ~ For this type of cleaning, the program must not be interrupted until completion. In other words, the On/Off Button must not be used.
~ When using cleaning agents and specialized products, it is essential that the manufacturer’s instructions are followed. Only use the product for the application described by the manufacturer to avoid any material damage or the occurrence of strong chemical reactions.
a Display b "Display" indicator c "Drying" indicator d "Start" indicator e "Start" 6 button f "Drying" 0 button g "Display" ß toggle button.
a Drying unit b Dispensers for neutralizer (red) and liquid detergent (blue) c Dispenser for powdered detergent d Rinse aid reservoir (with dosage selector) e Level indicator for rinse aid f Filter co.
Miele laboratory washers are designed to clean, rinse, and dry laboratory equipment. In this operating manual, the general term "labware" is used to cover a range of laboratory equipment. Always follow the labware manufacturer's instructions.
Electric door lock The machine is equipped with an electric door lock. The door can only be opened when ^ the electrical supply to the machine is turned on, and the ^ On-Off switch is pressed. To open the door ^ Press the a button in as far as it will go.
Before using the machine for the first time, the water softener should be programmed. The water needs to be softened to avoid calcium deposits on the items being cleaned and in the machine itself. If the water supply is harder or softer than the factory setting (including below 4 gr/gal or 70 ppm), the setting will need to be changed.
Settings Settings 1-3 0 gr/gal 1-3 0 ppm CaCO 3 Settings 31 -60 gr/gal 31 -60 ppm CaCO 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 2 3 4 5 6 7 8 9 10 11 12 13 .
Filling the salt reservoir Only special, coarse-grained reactivation salt* should be used in this machine. *Available from Miele. Please see back page for more information. Do not use other types of salt, e.g. table salt, agricultural or gritting salt.
Salt indicator When the salt reservoir is empty, the "Recharge Softener" indicator b lights to remind you to fill the reservoir. Reactivation takes place automatically as needed during a program. The "Recharging" indicator a lights while this is occurring.
Adding rinse aid Rinse aid is not used in laboratory glassware cleaning applications. If rinse aid is required, the rinse aid dosage must be activated with assistance from Miele Technical Service. Rinse aid (e.g., MieleClear) is filled in the storage container, and the selected dose is then dispensed automatically.
Rinse aid indicator light ^ Rinse aid does not need to be refilled until the "Rinse aid" indicator light comes on in the display. Setting the rinse aid dosage The dosage selector has settings from 1 to 6 (1 - 6 ml). The factory setting is at 3 (3 ml).
Adding neutralizer Neutralizer has an acidic pH, and works by neutralizing any traces of (alkaline) cleaner from the surface of the glassware. When a mild alkaline detergent is used for washing, select a neutralizer that contains phosphoric acid. The neutralizer is automatically dispensed during the second rinse after the main wash cycle.
Neutralizer indicator light ^ When the "Neutralizer" indicator light comes on, it is important to promptly refill or exchange the neutralizer container.
Adding detergent , Use only cleaning agents formulated for this machine. Do not use detergents formulated for household dishwashers. The factory setting is designed for liquid detergents. Although powered detergents can be used, Miele recommends that you use liquid detergents instead.
Liquid detergent refill light ^ When the " 8 Dosing Pump" indicator comes on, it is important to promptly refill or exchange the detergent container.
^ Load the detergent into the compartment. Dosage: To achieve a detergent concentration of approximately 3 g/l, use 30 g of detergent. Always follow the detergent manufacturer's recommendations for dosage concentration.
Depending on the type of labware you wish to clean, the washer can be used with an upper basket, lower basket, or injector wagon, as well as an assortment of inserts and special baskets to suit your needs. Baskets and inserts should be properly selected to match the application desired.
Loading the machine – Always load items in a way that all surfaces are exposed. This ensures that the items will be properly cleaned. – Do not nest any items inside other items. Keep each item separate. – Hollow vessels must be arranged for complete inside exposure to the cleaning water.
Spring adapter for the water connection The spring adapter for the water connection must be properly engaged when a basket or the injector wagon is inserted into the machine. It must be 4-5m m higher than the water inlet in the machine. If this is not the case, the adapter needs to be adjusted as follows: ^ Loosen the locking ring a .
Laboratory equipment Wide-necked labware, e.g., beakers, wide-necked Erlenmeyer flasks and Petri dishes, or cylindrical items, e.g., test tubes, can be cleaned inside and out by the rotating spray arms. For proper cleaning, load these items in whole, half or quarter inserts, and place them in an empty lower basket or upper basket with spray arm.
Upper basket O 188 For various inserts. Lower basket U 874 For various inserts. E 106 Stainless steel half insert with 28 spring hooks in 2 different heights for various glassware, e.g. narrow necked flasks, graduated cylinders, medicine bottles, etc.
E 350 Injector wagon For narrow necked glassware, 15 injectors, 160 mm high; 18 injectors, 220 mm high. O 187 Injector wagon (Upper basket) For direct injection of narrow necked glassware, 34 injectors,160 mm high.
Turning on ^ Close the door. ^ Press the I-0 button. If the program selector is in the f position, an indicator light will appear in the display. Starting a program ^ Turn the program selector clockwise or counterclockwise to the desired program. Refer to the "Program Guide" for more details.
Once a program cycle has started, all other programs are locked until completion. If the program selector is turned to a different program, the display goes out. The display will re-appear if the program selector is turned back to the running program.
End of a program Once the "Start" indicator goes out, and the "Complete" indicator comes on, the program has ended. You will see a 0 in the middle of the display, and all other indicators will show a running light. A buzzer sounds for a maximum of 30 seconds by default.
Canceling a program Avoid canceling a running program unless absolutely necessary, for example if the glassware is moving around excessively or the wrong program has been selected. , In cases of officially recognized epidemics, contaminated water must NEVER be drained from the machine.
Program Description Custom Open program available for programming by end user. INORGANICA For removing inorganic residue; generally for analytical applications, for light to moderate soiling, with moderate to high rinse requirements.
Program sequence Pre-Wash 12 Main Wash 12 Rinse 12 Rinse 34 Final Rinse * 12 Drying x 12 CW HW DOS 1 80°C 3 min HW DOS 3 HW DI DI 75°C 1 min 99°C 70°C 25 min 5 min CW DOS 3 50°C 1 min HW DOS 1 75.
For future servicing, be sure to document any changes made to the factory settings in the fields provided. General information: – Program selector positions that have no assigned function are represented by a bar ( - ) in the middle of the display. – To call up the programming level, use the f position.
DOS 1 (liquid detergent) Setting the detergent dosage The dosage concentration only needs to be set for liquid detergents. Set the concentration according to the detergent manufacturer's recommendations. Do not change the setting if you are using powdered detergent in the door dispenser.
DOS 3 (neutralizer) Setting the neutralizer dosage Set dosage concentration according to the neutralizer manufacturer's recommendations. Step Display / Result ^ Press the 0 button until E02 appears in the display. E02 ^ Turn the program selector to "Intensive".
Buzzer The buzzer can be programmed for the following functions: – a continuous tone at the end of a program, – an error signal that beeps in 1-second intervals, and – a sample-collection signal (allows a sample of the final rinse water to be collected) that beeps in sets of 3 followed by a 2-sec pause.
Changing program parameters The factory settings for various parameters are listed in the "Program Guide". Program parameters cannot be changed unless they are activated within a given program (see "Program Guide". It is important to document any changes e.
Changing the temperature Step Display / Result ^ Press and hold the 0 button until the setting of the desired program block appears in the display. E09 for Main Wash 1 E12 for Main Wash 2 E22 for Rinse 1 E25 for Rinse 2 E28 for Drying 1 E31 for Drying 2 ^ Set the program selector to the program you wish to change, e.
Restoring the factory settings Step Display / Result ^ Press and hold the 0 button until E33 appears in the display. E33 ^ Turn the program selector to a program. Default factory setting(s): Re-programmed setting(s): 00 PP ^ When PP appears in the display, press the ß button.
Setting the time and date The date and time are set in the serial interface (optional accessory). This information appears in the print log. The date and time can be changed, e.
Resetting the coarse and fine filter timer Whenever the coarse or fine filter in the drying unit are changed, the service timer should be reset to zero. Step Display / Result ^ Press and hold the 0 button until E04 appears in the display. E04 Switch the program selector to the position for the value you wish to change.
The machine is equipped with an interface socket so that data can be transferred from Novotronic to a log printer. Please contact Miele Technical Service to order printer cables. The serial interface is RS 232 compatible. Various printer types with Epson-compatible fonts can be used for printing.
Periodic maintenance for the machine is recommended annually. Routine checks The routine checks must be done daily by the user before using the machine.
, Wear protective gloves and goggles when cleaning this machine. Cleaning the filters in the wash cabinet , The machine must not be used without all filters in place.
Cleaning the fine, flat and micro-fine filters ^ Remove the coarse filter. ^ Remove the fine filter from between the flat and micro-fine filters. ^ To unscrew the micro-fine filter, grasp the two tabs and turn twice counterclockwise. ^ Then remove together with the flat filter.
Cleaning the spray arms The spray arms can get clogged. Check daily and clean if necessary. Removing the spray arms ^ Remove the baskets. Spray arm at the upper basket or mobile unit (if available): ^ Loosen the knurled nut and remove the spray arm. Metal knurled nuts have a left-hand thread.
Cleaning the drain pump and non-return valve If water has not been pumped away at the end of a program the drain pump or the non-return valve may be blocked. ^ Turn off the machine. ^ Remove the filter combination out of the wash cabinet. ^ Tilt the locking clamp to the side.
Cleaning the water inlet filters To protect the water inlet faucet, filters are incorporated in the intake hose attached to the water supply. If the filters are soiled they must be cleaned to ensure sufficient water intake to the wash cabinet.
Cleaning the control panel ^ The control panel should only be cleaned with a damp cloth or a suitable cleaner for use on plastic materials. , Do not use abrasive cleaners, glass cleaners or all-purpose cleaners! They will damage the control panel.
Baskets and inserts To ensure the function of baskets and inserts, they must be checked daily. A checklist is supplied with the machine. Check the following points: – Are the rollers in the proper c.
The following guide can be used to help address minor problems without a service call. , Repairs should only be performed by Miele Technical Service. Work performed by unqualified persons can place the user at considerable risk of harm.
What if... Possible fault Solution Before the start of a program, the " 8 Dosing Pump" indicator flashes, and the program can not be started. Before addressing the error: – Turn the program selector to f . The error message is erased. – Press the On-Off button to switch off the machine.
What if... Possible fault Solution Before the start of a program, the "Neutralizer" indicator flashes, and the program can not be started. Before addressing the error: – Turn the program selector to f . The error message is erased. – Press the On-Off button to switch off the machine.
What if... Possible fault Solution The "Recharge" indicator flashes. The water softener has run out of salt. Refill the salt reservoir. A few minutes after the start of a program, the "Fill/Drain" indicator flashes, and the program stops.
What if... Possible fault Solution The rinse program is interrupted and the "Fill/Drain" indicator light is flashing. Before addressing the error: – Turn the program selector to f . The error message is erased. – Press the On/Off button to switch off the machine.
What if... Possible fault Solution After a program, there is powdered detergent residue left behind in the door dispenser. The dispenser was wet when it was loaded. Make sure the dispenser is dry before loading it. The powdered detergent dispenser cover was blocked by glassware.
What if... Possible fault Solution Items made of glass show signs of corrosion. The items are not washer-safe. Only use washer-safe glassware. No neutralization took place in the program sequence. Fill the neutralizer container. Excessively high temperatures are causing glass corrosion.
What if... Possible fault Solution There are white deposits and/or spots on the labware. The water softener setting is too low. Test the tap water hardness and program the water softener according. Too much powder detergent is being used. Be sure you are using the correct amount of detergent.
What if... Possible fault Solution The wash result is unacceptable. The baskets and inserts were incorrectly loaded or overcrowded. Properly arrange the glassware. Do not overload baskets and inserts. The program used was not suited to the type/amount of soiling.
Thermo switch This machine has a resettable heater limiter which will shut off the elements in the event of over-heating. This could be caused for example, if large articles cover the heating elements or if the filters in the wash cabinet are blocked.
In the event of a fault which you cannot correct yourself please contact the Miele Technical Service Department U 1-800-991-9380 techserv@mieleusa.com V 1-800-565-6435 service@miele.ca ^ Please quote the model of your machine. This information can be found on the machine’s front panel.
INSTALLATION INSTRUCTIONS.
Please refer to the installation diagram supplied with the machine. , Furniture and fittings installed near the machine must be of a commercial standard, able to withstand the effects of steam. Installation options – Free-standing – Slot-in , next to other machines or furniture or in a suitable space.
Removing the lid (if necessary) ^ Open the door. ^ Remove the fixing screws on both sides using a cross slotted screwdriver. ^ Pull the machine lid approx.
, All electrical work must be carried out by a suitably qualified electrician in accordance with local and national safety regulations. – Connection should be made via a suitable isolator, with an on-off switch that is easily accessible for servicing work.
Connecting the water inlet , The water in the machine is not drinkable. – The machine must be connected to the water supply in accordance with local and national regulations. – The washer is constructed so it may be connected to a suitable supply without an extra non-return valve unless required by code.
– Connect the intake hose for the steam condenser (without water safeguard) to the cold water faucet. – See the next page for how to connect the DI water line. – Water valves with 3 / 4 inch thread are to be provided on site. They should be easily accessible, because the water supply will need to be turned off when not in use.
DI Connection (pressurized) The machine comes factory standard for connection to a pressure resistant system. The recommended water pressure (flow rate) is 25 - 60 psi however, water pressure that is 10 - 147 psi is acceptable.
Drainage ^ The drainage system is fitted with a non-return valve which prevents dirty water from flowing back into the machine via the drain hose. ^ The machine should preferably be connected to a separate drainage system onsite. If separate drainage is not available contact Miele Technical Service for advice.
English Metric Height: with lid 33.5" 85 cm without lid 32.3" 82 cm Width: 35.4" 90 cm Depth: 27.5" 70 cm Depth with the door open: 49.8" 126.5 cm Net weight: 265 lbs 120 kg Voltage / Fuse: see data plate Power cord approx. 5.
Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
75.
Subject to change without notice / 5207 M.-Nr. 07 157 440 / 00.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Miele G 7883 CD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Miele G 7883 CD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Miele G 7883 CD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Miele G 7883 CD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Miele G 7883 CD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Miele G 7883 CD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Miele G 7883 CD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Miele G 7883 CD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
