Manuel d'utilisation / d'entretien du produit WESY81081 du fabricant Weider
Aller à la page of 25
¨ USERÕS MANUAL Model No. WESY81081 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Limited W arranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 38 in. Length: 61 in. Low Pulley Station Foot Plate Row Bar High Pulley Station Leg Lever Butterfly Arm Butterfly Arm Press Arm Shroud Covering Weight Stack Seat Backrest Thank you for selecting the versatile WEIDER ¨ XP23 T raining System.
5 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
6 1. Before beginning assembly , make sure you have read and understood the information on page 5. Locate and open the parts bag labeled ÒFRAME ASSEMBL Y .Ó Press a 2Ó Square Outer Cap (51) onto each end of the Stabilizer (5). Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up through the Stabilizer (5) and place it flat on the floor .
7 4. Set four W eight Bumpers (19) onto the Base (8) and align them with the indicated holes. Insert both Weight Guides (23) through the Weight Bumpers (19) and the holes in the Base (8) .
8 7. Slide two 5/16Ó Flat W ashers (56) onto two 5/16Ó x 1 3/4Ó Bolts (58). Align the holes in the bracket on the T op Frame (1) with the holes in the Rear Upright (18). Insert the 5/16Ó x 1 3/4Ó Bolts (58) and hand tighten two 5/16Ó Nylon Locknuts (53) onto them.
9 1 1. Press a 2Ó Square Inner Cap (21) into the top end of each Press Arm (46). Press a 1Ó Round Inner Cap (49) into the indicated hole on each Press Arm (46). Attach each Press Arm (46) to the Press Frame (12) with two 5/16Ó x 2 3/4Ó Bolts (67) and two 5/16Ó Nylon Locknuts (53).
10 14. Locate and open the parts bag labeled ÒCABLE ASSEMBL Y AND PULLEYS.Ó For Cable identifica- tion and routing during steps 14Ð28, refer to the Cable Diagram and Cable ID Chart on page 16. Locate the Short Cable (9). It is approximately 127Ò long.
11 17. Move to the other side of the unit. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) and a Cable T rap (66) to the Right Butterfly Arm (48) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (63).
12 20. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) to the front bracket (M) underneath the T op Frame (1) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (63). Make sure the Bolt (62) is inserted from the direction shown on the drawing.
13 25. Thread the Long Cable (2) through the Press Frame (12). Wrap the Long Cable around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Press Frame with a 3/8Ó x 3 1/4Ó Bolt (69), a Cable T rap (66), a 3/8Ó Flat W asher (55) and a 3/8Ó Nylon Jamnut (57).
14 28. Wrap the Long Cable (2) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 1/2Ó Bolt (54), a Cable T rap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó Nylon Jamnut (57). Attach the closed loop on the end of the Long Cable (2) onto the Eyebolt (44) with a Cable Clip (73).
15 31. Press two 3/4Ó Round Inner Caps (34) into each Pad T ube (28). Insert one Pad T ube into the Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube into the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad T ube.
16 Cable Diagram The Cable Diagram below shows the proper routing of the Short Cable (9) and the Long Cable (2). The numbers show the correct route for each Cable. Make sure the Cables are routed correctly , that the Pulleys move smoothly and that the Cable T raps do not touch or bind the Cables.
Attaching the Lat Bar , Row Bar or Handle to the High Pulley Station Attach the Lat Bar (76) to the Short Cable (9) with a Cable Clip (73). For some exercises, the Chain (74) should be attached between the Lat Bar and the Long Cable with two Cable Clips.
18 Press Butterfly High Leg Low Weight Arm Arm Pulley Lever Pulley Plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) To p 12 46 19 21 15 1 40 70 33 37 33 2 62 97 49 54 45 3 86 1 10 68 68 59 4 94 141 81 88 72 .
19 Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the Cables before resistance is felt, the Cables should be tightened. T o tighten the Cables, insert the Weight Pin (39, not shown) between the third and the fourth Weight, counting from the top.
60 31 31 35 35 57 34 34 30 30 44 33 28 30 34 28 30 34 81 22 82 71 38 17 37 13 80 33 29 36 9 58 53 23 16 25 64 26 74 73 75 19 45 45 21 21 3 4 4 3 15 62 66 35 63 15 48 47 2 7 7 7 7 7 11 58 56 53 53 18 6.
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 T op Frame 2 1 Long Cable 3 2 1Ó Round Cover Cap 4 4 1Ó Retainer 5 1 Stabilizer 6 2 ÒVÓ-Pulle.
1" Retainer (4) 1/4" Flat W asher (81) 3/8" x 2" Bolt (62) 3/8" x 3 1/2" Bolt (54) Cable Clip (73) 3/8" x 3 1/4" Bolt (69) 1/4" x 1/2" Screw (17) 3/8&.
5/16" x 1 1/2" Bolt (61) 1/4" x 2" Bolt (71) 1/4" x 2" Carriage Bolt (38) 1/4" x 2 1/2" Screw (43) 5/16" x 2 3/4" Bolt (67) 5/16" x 2 1/2" C.
1" Round Inner Cap (49) 1" Round Cover Cap (3) 3/4" Round Inner Cap (34) 5/16" x 2" Eyebolt (44) 1 1/2" Square Inner Cap (33) 2" Square Inner Cap (21) 2" Square.
Ordering Replacement Parts T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weider WESY81081 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weider WESY81081 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weider WESY81081, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weider WESY81081 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weider WESY81081, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weider WESY81081.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weider WESY81081. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weider WESY81081 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
