Manuel d'utilisation / d'entretien du produit WESY17011 du fabricant Weider
Aller à la page of 27
CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY1701 1 Serial No. (Write the serial number in the space above for reference.) Serial Number Decal (under seat) Visit our website at www .
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only .
4 ASSEMBLED DIMENSIONS: Height: 76 in. Width: 37 in. Length: 48 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Curl Pad We ight Carriage Seat Backrest BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER ® 15CT weight system.
5 Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
6 1 56 3 5 51 51 14 1 27 4 1. Before beginning assembly , be sure that you have read and understand the information in the box on the previous page. Press a 50mm Square Outer Cap (51) onto each end of the Stabilizer (5). Press a 50mm Square Inner Cap (27) into the end of the Base (4).
7 4 4 T ube Wel ded Spacers 17 59 Lubricate 21 9 9 3. Press a 45mm Square Inner Cap (44) into each end of the crossbar on the T op Frame (55). Press two 25mm Round Inner Caps (49) into the top of the crossbar . Press a 50 mm Square Inner Cap (27) into the top of the Rear Upright (56).
8 7. Lubricate both axles on the T op Frame (55). Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 6 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the T op Frame.
9 11 10 50 58 7 47 58 21 7 21 6 50 6 42 10. W rap the Long Cable (58) around a “V”-Pulley (6). Attach the “V”-Pulley and a Long Cable T rap (50) to the indicated bracket on the Front Upright (42) with an M10 x 60mm Bolt (7) and an M10 Nylon Locknut (21).
10 14. Locate the Long “U”-Bracket (57) that is pre- assembled with a 90mm Pulley (15) and a Cable T rap (not shown). Route the Long Cable (58) around the Pulley and through the Long “U”- Bracket.
11 17 21 15 12 15 66 9 21 4 Bracket 17 25 17. Using an M10 x 80mm Bolt (25), an M10 W asher (9), and an M10 Nylon Locknut (21), secure a 90mm Pulley (15) and a Cable T rap (66) to the upper hole in the Press Frame (17). Make sure that the Cable T rap and the Pulley are oriented as shown.
12 21. Route the Short Cable (23) up around the 90mm Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable is routed around the Pulley as shown, and that the Cable T rap (66) is turned to hold the Cable in place.
23. Attach the Backrest (41) to the Front Upright (42) with two M6 x 63mm Screws (43) and two M6 W ashers (10). SEA T ASSEMBL Y 23 41 42 10 43 13 24. Press a 38mm Square Inner Cap (32) into the Seat Frame (36). Insert an M6 x 50mm Carriage Bolt (38) into the center hole in the Seat Plate (37).
14 26. Rest the Seat Frame (36) on the indicated pin in the Front Upright (42). Attach the Seat Frame to the Front Upright with an M8 x 67mm Carriage Bolt (14) and the Seat Knob (40). 26 36 40 Pin 42 14 27. Press 19mm Round Inner Caps (34) into the ends of both Pad T ubes (28).
15 30. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, beginning on the following page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
16 ADJUSTMENT The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
17 AT T ACHING THE LEG LEVER TO THE LOW PULLEY ST A TION To use the Leg Lever (29), the seat must be attached to the front upright (see A TT ACHING AND REMOV- ING THE SEA T on page 16). Attach the Short Cable (23) to the M10 Eyebolt (35) with a Cable Clip (53).
18 WEIGHT ON PRESS ARM BUTTERFL Y ARM LOW PULLEY/ HIGH PULLEY WEIGHT (lbs.) (lbs.) LEG LEVER (lbs.) CARRIAGE (lbs.) 01 2 7 10 10 52 2 1 1 1 8 1 6 10 31 15 25 21 15 40 20 32 26 20 50 24 39 32 25 59 29 .
19 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
20 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (58). Use the dia- gram to be sure that the two cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight system will not function properly and damage may occur .
21 NOTES.
22 Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY1701 1 R0802B Key No.
15 23 56 15 12 3 57 23 21 3 5 51 14 51 4 1 27 16 7 50 6 21 63 62 63 62 47 48 44 45 44 45 13 40 38 37 18 32 28 30 34 10 2 24 36 30 34 14 61 3 29 34 30 28 49 46 32 30 34 49 49 46 22 3 9 25 59 17 21 52 4.
M10 Eyebolt (35) M6 Nylon Locknut (2) M8 Nylon Locknut (3) M10 Nylon Locknut (21) M6 W asher (10) M8 W asher (8) M6 x 50mm Screw (24) M6 x 63mm Screw (43) M8 x 63mm Bolt (22) Cable Clip (53) M10 W ash.
M10 x 60mm Bolt (7) M10 x 45mm Bolt (12) M10 x 90mm Bolt (16) M10 x 80mm Bolt (25) M10 x 198mm Bolt (59) M8 x 70mm Bolt (1 1) M8 x 67mm Bolt (61) M8 x 1 15mm Bolt (64) M8 x 67mm Carriage Bolt (14) M10.
50mm Square Outer Cap (51) 50mm Square Inner Cap (27) 38mm Square Inner Cap (32) 19mm Round Inner Cap (34) 45mm Square Inner Cap (44) 25mm Round Inner Cap (49) 25mm Round Cover Cap (62) 25mm Square In.
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays).
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weider WESY17011 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weider WESY17011 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weider WESY17011, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weider WESY17011 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weider WESY17011, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weider WESY17011.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weider WESY17011. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weider WESY17011 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
