Manuel d'utilisation / d'entretien du produit 8530 du fabricant Weider
Aller à la page of 25
USERÕS MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis- tance from our factory .
2 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the home gym system. 1. Read all instructions in this manual and in the accompanying literature before using the home gym system.
3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 74 in. Width: 60 in. Length: 54 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Squat Arm Press Arm Weight Stacks Backrest VKR Arms Weight Pin Thank you for selecting the versatile WEIDER ¨ 8530 Home Gym System.
4 ASSEMBL Y 1 74 56 3 3 8 11 51 27 1 4 3 1 51 27 High Side 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Press a 2Ó Inner Cap (27) into the indicated end of the Stabilizer (5). Press 2Ó Outer Caps (51) onto the other two locations on the Stabilizer .
4 2 3 5 2. Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (1) up through the Base (4). Slide the Front Upright (42) onto the 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Base (4). Hand-tighten a 5/16Ó Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet.
5 6 6 5. Press a Weight Tube Bumper (64) into the end of a Weight T ube (63). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pins on the Weight T ube are sitting in the pin grooves in the top Weight. Lubricate the inside of the holes in a T op Weight (65).
7. Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) with a 5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and a 5/16Ó Nylon Locknut (3). Be sure that the Pulley Bracket (20) is in front of the right Long Weight Guide (62) as shown.
8 1 1. Lubricate both axles on the T op Frame (55). Slide the Right Arm (48) onto the right axle. Be careful not to confuse the Right Arm with the Left Arm (47); note the position of the ÒVÓ Pulley (50) to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the T op Frame (55).
9 During steps 13 to 25, refer to the CABLE DIA- GRAM on page 19 of this manual. Identify the three cables by their lengths, and note the positions of the cable traps. IMPORT ANT : Do not overtighten the bolts and nuts securing the pulleys. The pulleys must turn freely .
10 17. Route the Medium Cable (58) around the 3 1/2Ó Pulley (15) attached to the bracket on the T op Frame (55). T ighten the 3/8Ó x 2Ó Bolt (12) and the 3/8Ó Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identifica- tion.
11 21. Attach the Medium Cable (58) to a Small ÒUÓ- Bracket (71) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat W asher (10). Do not tighten the 1/4Ó Nylon Locknut.
12 23. Route the Long Cable (72) around the 3 1/2Ó Pulley (15) on the T op Frame (55). T ighten the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó Bolt (not shown).
13 25. See inset drawing A. Note: The inset draw- ing shows the view from the other side of the Squat Arm Upright (56). Wrap the Long Cable (72) around a ÒVÓ-Pulley (50).
14 28. Press a 1 1/2Ó Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16Ó x 2 1/4Ó Bolt and a 5/16Ó Nylon Locknut (3). Insert the 5/16Ó x 2Ó Eyebolt (35) into the Leg Lever (29) from the direction shown.
32. Wet the handle on the Right VKR Arm (80) with soapy water . Slide a 5Ó Plastic Grip (83) onto the Handle. Press a 1Ó Round Inner Cap (49) into the bottom of the handle. Attach a 5Ó Plastic Grip (83) and a 1Ó Round Inner Cap (49) to the handle on the Left VKR Arm (79) in the same manner .
16 HOW T O USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.
17 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16Ó x 2 3/4Ó Carriage Bolt (14) and the Seat Knob (40).
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent.
19 CABLE DIAGRAM The cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and the Short Cable (23). Use the diagram to be sure that the three cables and cable traps have been assembled cor- rectly .
P ART LISTÑModel No. WESY85301 R0100A Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
68 3 20 21 15 66 12 27 83 78 80 75 75 10 81 77 32 83 78 79 3 10 43 74 11 11 3 51 1 1 27 19 51 21 5 25 64 26 12 66 15 63 65 24 2 71 72 3 67 31 50 76 21 56 54 83 83 52 53 39 21 93 92 15 94 84 3 8 8 22 4.
1" Retainer (69)Ð4 3/8" x 3 1/2" Bolt (16)Ð1 1/4" x 3/4" Screw (18)Ð2 5/16" x 5" Bolt (68)Ð1 3/8" x 3 3/4" Bolt (88)Ð4 3/8" x 8" Bolt (59)Ð.
1" Round Inner Cap (49)Ð6 1" Round Cover Cap (70)Ð2 3/4" Round Inner Cap (34)Ð4 1/2" x 3/4" Spacer (61)Ð4 5/16" x 2" Eyebolt (35)Ñ1 1 1/2" Inner Cap (32)Ð.
5/16" Nylon Locknut (3)Ð27 1/4" Flat W asher (10)Ð13 5/16" Flat W asher (8)Ð7 3/8" Flat W asher (9)Ð4 1/4" x 2 1/2" Screw (43)Ð4 3/8" Nylon Locknut (21)Ð16 1/4.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weider 8530 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weider 8530 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weider 8530, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weider 8530 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weider 8530, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weider 8530.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weider 8530. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weider 8530 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
