Manuel d'utilisation / d'entretien du produit 831.159530 du fabricant Weider
Aller à la page of 35
USER’S MANUAL Model No. 831.159530 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only .
4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 103 in. Depth: 55 in. Low Pulley Station Foot Plate Leg Lever Press Arms Decal 1 Decal 1 Decal 2 Backrest Curl Pad Butterfly Arms Ab Pulley Station Leg Press Arm Thank you for selecting the innovative and versatile WEIDER ® PRO 9950 weight system.
5 Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Before beginning, make sure that you have read and understood the information on page 5. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1 and 2.” Press a 2” Square Inner Cap (59) into each end of the Butterfly Base (1). Insert four 5/16” x 2 1/2” Carriage Bolts (54) up through the Butterfly Base (1).
4. Press a 1 1/2” Square Inner Cap (100) into the indicated part of the Press Upright (6). Orient the Press Upright (6) as shown. Attach the Press Upright to the indicated 5/16” x 2 1/2” Carriage Bolts (54) in the Press Base (3) with two 5/16” Nylon Locknuts (64).
8. Attach the T op Frame (5) to the Butterfly Upright (4) with two 3/8” x 2 3/4” Bolts (58), a Short Support Plate (26), and two 3/8” Nylon Locknuts (74). Note: Be sure that the T op Frame is ori- ented with the long bracket on the side shown, and that it rests between the Weight Guides (33) as shown in step 9.
9 12 13 14 55 55 66 66 9 Adjustment knob must be on this side 64 10 54 64 12 59 71 72 3 64 64 66 55 6 10 66 66 64 1 1. Press a 2” Square Inner Cap (59) into the Press T op Frame (13). Attach the Press T op Frame (13) to the Press Upright (6) with two 5/16” x 2 3/4” Bolts (55), a Long Support Plate (34), and two 5/16” Nylon Locknuts (64).
85 86 Axle 10 15. Locate and open the parts bag labeled “ARM ASSEMBL Y .” Press a 2” Square Inner Cap (59) into each end of the Leg Lever (8). Lubricate the 3/8” x 3 1/4” Bolt (101). Attach the Leg Lever (8) to the Butterfly Front Leg (9) with the Bolt and a 3/8” Nylon Jamnut (88).
18 18. Press two 1 3/4” Square Inner Caps (60) into the top of the Press Frame (14). Lubricate the 3/8” x 9” Bolt (92). Attach the Press Frame (14) to the Press T op Frame (13) with the Bolt, four 3/8” SAE W ashers (102), and a 3/8” Nylon Locknut (74).
21 12 24. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley to the indicated side of the Press Frame (14) with a 3/8” x 3 1/2” Bolt (65), a 3/8” W asher (75), and a 3/8” Nylon Locknut (74). 24 22. Locate and open the parts bag labeled “CABLE ASSEMBL Y .
13 27. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley and a Cable T rap (44) to the Press Upright (6) with a 3/8” x 3 3/4” Bolt (62), a 3/8” W asher (75), and a 3/8” Nylon Locknut (74). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
14 30. Wrap the Press Cable (80) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (50) to the indicated hole in the Press Seat Frame (12), using a 3/8” x 4 1/4” Bolt (104), a 3/8” W asher (75) and a 3/8” Nylon Locknut (74).
15 34. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley to the bracket on the T op Frame (5) with a 3/8” x 2” Bolt (79) and a 3/8” Nylon Locknut (74).
16 37. Wrap the Butterfly Cable (81) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (50) to the indicated side of the bracket on the Butterfly Upright (4) with a 3/8” x 2 1/2” Bolt (78) and a 3/8” Nylon Locknut (74). Be sure the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
17 41 37 74 49 49 83 Rod Ball Large tabs must be on this side 4 75 75 41. Identify the Ab Cable (83); it is approximately 220.25” long and it has a ball on one end and a loop on the other . Wrap the Ab Cable (83) around a 3 1/2” Pulley (37). Place two Pulley Covers (49) over the Pulley; make sure that the large tabs are in the position shown.
18 45. Wrap the Ab Cable (83) around a 3 1/2” Pulley (37). Attach the Pulley to the bracket on the Butterfly T op Frame (19) with a 3/8” x 2” Bolt (79) and a 3/8” Nylon Locknut (74). 45 37 19 83 Bracket 74 79 46. W rap the Ab Cable (83) around a 3 1/2” Pulley (37).
49 50 19 49. Wrap the Leg Press Cable (82) around a 3 1/2” Pulley (37). Attach the Pulley and a Cable T rap (44) to the Butterfly Upright (4) with a 3/8” x 5” Bolt (61) and a 3/8” Nylon Locknut (74). Do not tighten the Nylon Locknut yet. Be sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
20 53. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Press a 1 1/2” Square Inner Cap (100) into the bottom of a Seat Bracket (1 1). Press two 1” x 2” Inner Caps (70) into the ends of the Seat Bracket. Insert a 1/4” x 1 3/4” Carriage Bolt (93) into the center hole of a Support Plate (57).
21 56 106 57 90 90 84 51 6 70 21 84 98 100 93 20 57. Press a 1 3/4” Square Inner Cap (60) into the back of the Adjustment T ube (23). Attach the Adjustment T ube (23) to the Press Plate (24) with a 5/16” x 2 1/2” Bolt (63), two 5/16” W ashers (66), and a 5/16” Nylon Locknut (64).
59 22 59. Attach the Curl Pad (36) to the Curl Post (35) with two 1/4” x 3/4” Bolts (90). 35 90 90 36 60. Make sure that all parts have been properly tightened before using the weight system. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on page 23 of this manual.
ADJUSTING THE SEA T T o adjust the height of the Seat (25) on the Press Seat Frame (12), loosen the Adjustment Knob (51) by turning it counterclockwise, and pull it out as far as possible. Move the Seat to the desired height and snap the Knob into an adjustment hole in the Seat Bracket (1 1).
24 36 35 59 9 45 47 47 68 48 27 31 Weight T ube 28 52 A TT ACHING THE CURL P AD T o use the Curl Pad (36), remove the 2” Square Inner Cap (59) and insert the Curl Post (35) into the Butterfly Front Leg (9). Secure the Curl Post with the Curl Adjustment Knob (52).
25 Weight High Arm Leg Butterfly Leg Lever Low Arm (lbs.) Pulley Press Press Arm (lbs.) Pulley (lbs.) (lbs.) (lbs.) (lbs.)* (lbs.) 20 30 23 44 9 26 22 40 60 45 88 18 52 45 60 90 68 132 27 78 67 80 120.
26 The cable diagrams below show the proper routing of the Butterfly Cable (81), the Ab Cable (83), the Leg Lever Cable (82) and the Press Cable (80). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly , that the pulleys move smoothly , and that the cable traps do not touch or bind the Cables.
27 Slack can be removed form the Press Cable (80) by moving the indicated “V”-Pulley (38) to one of the four free holes in the Press Seat Frame (12). Remove the 3/8” x 4 1/4” Bolt (104), 3/8” W asher (75), and 3/8” Nylon Locknut (74) from the Press Seat Frame, Pulley , and Long Cable T rap (50).
Part No. 177796 R1001A Printed in Canada © 2001 Sears, Roebuck and Co. SEARS, ROEBUCK AND CO., HOFFMAN EST A TES, IL 60179 Model No. 831.159530 QUESTIONS? If you find that: • you need help assembli.
Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable assembly; and 4) seat assembly . The hardware for each assembly stage is packaged separately .
1” Retainer (85) 1" CoverCap (86) 1 3/4" Square Inner Cap (60) 1" Inner Cap (32) 1" x 2” Inner Cap (70) 1 1/2" Round Inner Cap (67) 3/4" Round Inner Cap (73) 2" .
3/8" Nylon Locknut (74) 3/8" Nylon Jamnut (88) 5/16" Nylon Jamnut (105) 1/2" Nylon Locknut (95) 1/4" x 1 3/4" Screw (98) 5/16" Nylon Locknut (64) 3/8" x 2".
3/8" x 3 1/2" Bolt (65) 3/8" W asher (75) 3/8" x 3 3/4" Bolt (62) 3/8 " x 9 " Bolt (92) 5/16" W asher (66) 5/16" x 2 3/4" Bolt (55) 3/8" x 3 1/4&.
81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL.
Key No. Qty . Description Key No. Qty . Description 1 1 Butterfly Base 2 1 Center Base 3 1 Press Base 4 1 Butterfly Upright 5 1 T op Frame 6 1 Press Upright 7 1 Support Brace 8 1 Leg Lever 9 1 Butterf.
45 48 47 24 64 46 23 60 66 63 22 74 37 44 44 37 61 96 69 95 89 89 74 74 64 2 29 29 74 32 32 32 32 31 30 30 31 30 30 27 27 27 27 30 30 31 78 78 78 78 28 28 29 29 80 83 33 33 64 74 74 74 20 53 37 91 55 .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weider 831.159530 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weider 831.159530 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weider 831.159530, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weider 831.159530 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weider 831.159530, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weider 831.159530.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weider 831.159530. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weider 831.159530 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
