Manuel d'utilisation / d'entretien du produit SK58 du fabricant Stanley Black & Decker
Aller à la page of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 70744 8/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance SK58 HYDRAULIC SINKER DRILL.
.
SK58 User Manual ◄ 3 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PRECAUTIONS .............................................
4 ► SK58 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
SK58 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► SK58 User Manual 02754 SK58 Name T ag 03786 GPM Sticker SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
SK58 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► SK58 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
SK58 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► SK58 User Manual NOTE: If uncoupled hoses are left in the sun, pressure in- crease within the hoses may make them difcult to connect. When possible, connect the free ends of the hoses together . 5. Connect the hose from the air supply to the hose on the tool.
SK58 User Manual ◄ 1 1 8. After the rock bit has carved out a depression in the material being drilled, open the hydraulic valve le- ver fully . Readjust the motor control knob to obtain a good drilling speed. Adjust the air valve to ensure the cuttings are being extracted from the drill hole.
12 ► SK58 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic system.
SK58 User Manual ◄ 13 PROBLEM CAUSE REMEDY T ool does not run. Power unit not functioning. Check power unit for proper ow and pressure (7–9 gpm/26–34 lpm, 1500–2000 psi/105–140 bar . Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports.
14 ► SK58 User Manual ACCUMULA TOR CHARGING 1. Perform steps 1 through 4 of the accumulator test- ing procedure above. 2. Connect the chuck of the charging assembly to the charging valve on the accumulator tester or , if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve.
SK58 User Manual ◄ 15 Figure 2. Charging the Accumulator CHARGING THE ACCUMULA TOR.
16 ► SK58 User Manual Shank Size (SK581 10 Air , SK58120 W ater , SK58310 UW Air) .................................................... 4-1/4 in. × 1 in. Hex Shank Size (SK58130 Air) ..................................................................
SK58 User Manual ◄ 17 SK58 P ARTS ILLUSTRA TION.
18 ► SK58 User Manual ITEM P ART NO. QTY DESCRIPTION 1 04763 1 AIR TUBE (SK581 10/SK58130/SK58310 ONL Y) 04965 1 W A TER TUBE (SK58120 ONL Y) 2 07064 1 VENT PLUG 3 04964 2 HANDLE GRIP ASSEMBL Y 4 01.
SK58 User Manual ◄ 19 SK581 10 – 1 INCH × 4-1/4 HEX SHANK AIR SK58120 – 1 INCH × 4-1/4 HEX SHANK W A TER SK58130 – 7/8 INCH × 4-1/4 HEX SHANK AIR SK58310 – 1 INCH × 4-1/4 HEX SHANK AIR, UNDER- W A TER USE NOTE: USE P ART NUMBER AND P ART NAME WHEN OR- DERING.
20 ► SK58 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
SK58 User Manual ◄ 21 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Stanley Black & Decker SK58 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Stanley Black & Decker SK58 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Stanley Black & Decker SK58, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Stanley Black & Decker SK58 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Stanley Black & Decker SK58, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Stanley Black & Decker SK58.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Stanley Black & Decker SK58. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Stanley Black & Decker SK58 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
