Manuel d'utilisation / d'entretien du produit VPC-SX560E du fabricant Sanyo
Aller à la page of 33
SER VICE MANUAL Color Digital Camera VPC-SX560EX VPC-SX560 (Product Code : 126 279 01) (Europe) (P AL Genenral) (Product Code : 126 279 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2 2. DISASSEMBLY ............
– 2 – Fig. 1-1.Optical Black Location (T op View) Pin No. 1 Symbol 2, 3 4 5, 6, 8, 14, 16 7, 9, 12 10 11 13 15 17 18 19 V φ 1 V φ 3 NC GND V OUT V DD C SUB V L φ RG H φ 1 Pin Description V ert.
– 3 – 1A 1 1Y 2 2A 3 2Y 4 3A 5 3Y 6 GND 7 4Y 8 4A 9 5Y 10 5A 11 6Y 12 6A 13 V CC 14 Fig. 1-3. IC902, IC904 and IC908 Block Diagram Fig. 1-4. IC907 Block Diagram 3.
– 4 – Fig. 1-6. Horizontal T ransfer of CCD Imager and Extraction of Signal V oltage Fig. 1-7. Theory of Signal Extraction Operation Reset gate pulse 12V Pre-charge drain bias （ PD ） Direction of transfer Voltage output Electric charge H Register Floating diffusion gate is floated at a high impedance.
– 5 – 1-2. CA2 CIRCUIT DESCRIPTION 1. Circuit Description 1-1. Scannning converter (Interlace converter) This circuit uses the function of a 64-Mbit SDRAMs to con- vert the non-interlaced signal which is output from the CCD into an interlaced signal for the video monitor .
– 6 – 3. LCD Block During EE, gamma conversion is carried out for the 10-bit RGB data which is input from the A/D conversion block of the CCD to the ASIC in order that the γ revised can be displayed on the video. The YUV of 640 x 480 is then transferred to the SVRAM.
– 7 – 1-3. CA3 CIRCUIT DESCRIPTION 1. Outline This is the main CA3 power block, and is comprised of the following blocks. Switching controller (IC521) Analog system 5.0 V power output (L5201, Q5203, D5201, C5206) Backlight power output (L5101, Q5102, D5101, C5106) 2.
– 8 – 1-4. PW1 POWER CIRCUIT DESCRIPTION 1. Outline This is the main PW1 power circuit, and is comprised of the following blocks. Switching controller (IC501) Digital and LCD system and 5.0 V system power output (L5010, Q5002, D5013, C5061, C5015) Digital 3.
– 9 – 1-5. PW1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit When UNREG power is supplied to the charge circuit and the CHG signal becomes High (3.3 V), the charging circuit starts operating and the main electorolytic capacitor is charged with high-voltage direct current.
– 10 – Pin Signal 1 2~7 8 9 10 11 13 14~19 20 21 22 31 32~69 70 71 73 74 75 76 77 78 79 80 81 82 84 86 87 88~90 83 85 91~93 CHG VOL SCAN IN VREF STBY (R) LED STBY (G) LED VSS NOT USED A VREF ON BUZZER CHG ON NOT USED VSS NOT USED P (A) ON P ON DIN CONNECT CARD A V JACK SO SCK IC XOUT XIN VDD XCIN XCOUT RESET BA T OFF RXD S.
– 11 – 0 1 2 0 1 23 SCAN OUT SCAN IN LEFT SEQUENTIAL SHOT POWER UP SHOOTING VIDEO CLIPS INFO OPTION RIGHT IMAGE DOWN STILL IMAGE PLA Y T able 4-2. Key Operation 2. Internal Communication Bus The SY1 circuit board carries out overall control of camera operation by detecting the input from the keyboard and the conditio n of the camera circuits.
– 12 – ASIC, memory CCD 8 bit CPU MODE LCD LCD MONITOR Supply voltage Power OFF Play back Shutter switch ON Resolution, Flash, Self timer switch ON LCD finder 3.
– 13 – 2. DISASSEMBL Y 2-1. REMOV AL OF CABINET ASSEMBL Y (FRONT) AND CABINET ASSEMBL Y (BACK) 2-2. REMOV AL OF SY1 BOARD 1. Two screws 1.7 x 2.5 2. Connector 3. Remove the solders. 4. Connector 5. SY1 board 6. Speaker 7. Heat sink rubber A 8. Heat sink A 21.
– 14 – 2-3. REMOV AL OF HOLDER BA TTERY AND PW1 BOARD 2-4. REMOV AL OF LCD, LENS ASSEMBL Y AND CA1 BOARD 1. Screw 1.7 x 2.5 1. Screw 1.7 x 2.5 2. Two screws 1.7 x 3.0 2. Two screws 1.7 x 3.0 3. Remove the solders. 4. Holder battery 5. Three screws 1.
– 15 – 2-5. REMOV AL OF CA3 BOARD AND CA2 BOARD 2-6. BOARD LOCA TION CA1 board SY1 board PW1 board CA2 board CA3 board 1. Three screws 1.7 x 2.5 7. CA2 board 8. Holder chassis M 2. Two screws 1.7 x 4.0 3. Lens VF 4. Two screws 1.7 x 2.5 5. Two connectors 4.
– 16 – 3. ELECTRICAL ADJUSTMENT 3-1. T able for Servicing T ools Note : J-1 color viewer is 100 - 1 10 V AC only . 3-2. Equipment 1. Oscilloscope 2. Digital voltmeter 3. AC adaptor 4. IBM R -compatible PC 5. DC regulated power supply 3-3. Adjustment Items and Order 1.
– 17 – 3-5. Connecting the camera to the computer 1. T urn of f both camera and computer . 2. Line up the arrow on the serial cable connector with the notch on the camera's serial port. Insert the connector . In case of USB cable, line up the arrow on the USB cable connector with the notch on the camera's USB port.
– 18 – 3-6. Adjust Specifications [PW1 board (Side B)] Note: 1. V oltage adjustment is necessary to repair in the PW1 board and replace the parts. 2. Power voltage set about +3.0 V . Preparation: 1. Connect CN104 on the CA2 board and CN502 on the PW1 board with extension cord.
– 19 – 4. AWB adjustment value will appear on the screen. 5. Click the OK. 8. Lens Adjustment Preparation: POWER switch: ON Adjustment condition: More than A3 size siemens star chart Fluorescent light illumination with no flicker Illumination above the subject should be 400 lux ± 10 %.
– 20 – CL173 waveform 4.0 V ± 0.1Vp-p CL173 waveform VG 10-2. LCD RGB Offset Adjustment Adjusting method: 1. Adjust LCD “ RGB offset ” so that the amplitude of the CL173 waveform is 7.3 V ± 0.3 Vp-p. 10-3. LCD Gain Adjustment Adjusting method: 1.
– 21 – 4. USB STORAGE INFORMA TION REGISTRA TION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save the USB storage data.
– 22 – 5. TROUBLESHOOTING GUIDE POWER LOSS INOPER TIVE MAIN SW MAIN SW ON NORMAL IC301-4 (SCAN IN 0) PULSE INPUT CHECK S3062, R3021 IC302-7 (UNREG) CHECK PW1, CA2 IC301-81 (VDD) IC301-84 (RESET) C.
23 6. PARTS LIST LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION N.S.P.: Not available as service parts. CABINET & CHASSIS PARTS 1 1 636 059 9901 ASSY,COVER LENS A-SX114EX 2 636 057 8296 ASSY,CABI FRONT-SX113/J 3 411 018 2304 SCR PAN PCS 1.
24 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION N.S.P.: Not available as service parts. CABINET & CHASSIS PARTS 2 1 645 035 4458 LENS(ASSY) 2 411 018 1802 SCR PAN PCS 1.
25 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION Note: 1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-PO.
26 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION R9014 401 224 9402 MT-GLAZE 1.0M JA 1/16W R9015 401 225 0903 MT-GLAZE 82K JA 1/16W R9016 401 224 8801 MT-GLAZE 100 JA 1/16W R9017 401 224 8801 MT-GLAZE 100 JA 1/16W R9018 401 225 0200 MT-GLAZE 3.
27 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C1090 403 311 4505 CERAMIC 1000P K 50V C1091 403 311 4505 CERAMIC 1000P K 50V C1093 403 311 4505 CERAMIC 1000P K 50V C1101 403 329 6508 TA-SOLID 10U M 6.3V C1102 403 343 8700 CERAMIC 1U M 12V C1112 403 346 2309 CERAMIC 0.
28 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION Q1707 405 102 5500 TR 2SB1218A-R OR 405 092 4200 TR 2SA1576-R Q5101 405 115 6907 TR DTC114EE Q5102 405 153 3302 TR SSM3K01F(BRA) Q5103 .
29 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION CN176 645 038 1843 PULG,4P (N.S.P) CN512 645 005 6901 PLUG,SIDE-ZR-SM3 (N.S.P) (MISCELLANEOUS) Y1702 636 055 2982 SPACER SHIELD CA3,SID.
30 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C5076 403 335 1405 CERAMIC 10U K 6.3V C5077 403 335 1405 CERAMIC 10U K 6.3V C5081 403 345 3000 POS-SOLID 47U M 6.3V C5401 403 345 3000 POS-SOLID 47U M 6.3V C5403 403 350 2005 CERAMIC 0.15U K 10V C5404 403 276 1304 CERAMIC 1000P K 50V C5406 403 343 3101 CERAMIC 1U K 6.
31 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION IC302 409 383 1008 S-8423NFS IC303 410 298 3605 IC S-8324A50MC-EPE IC311 409 407 0505 IC TK11331BM IC312 409 432 2505 IC LMV321M7X IC31.
32 Nov/ '00 / 4760 MI Printed in Japan SANYO Electric Co.,Ltd. Osaka, Japan LOCATION PARTS NO. DESCRIPTION ACCESSORIES 645 043 5492 BATTERY CHARGER,VPC-SX560E ONLY 645 044 8249 BATTERY CHARGER,EXCEPT VPC-SX560E 645 037 0205 BATTERY,RECHARGE,COMP.
O VERALL WIRING.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sanyo VPC-SX560E c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sanyo VPC-SX560E - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sanyo VPC-SX560E, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sanyo VPC-SX560E va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sanyo VPC-SX560E, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sanyo VPC-SX560E.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sanyo VPC-SX560E. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sanyo VPC-SX560E ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
