
Thank you for purchasing this bio-ethanol fireplace. You have purchased a quality product that will last you many years when used properly.
Please read this installation guide and user’s manual carefully before installing and using the fireplace.
This fireplace contains no asbestos products.
Location: A bioethanol fireplace can be placed anywhere, e.g. in a living room but also in a bedroom, the (residential) kitchen, chalet or mobile home.
One of the advantages of bioethanol fireplace is that it can be easily placed and moved. If you change your furniture, simply move your fireplace to another location. In addition, the cost of investment in a bio-ethanol fireplace is low, especially compared to traditional fireplaces and stoves. Besides atmosphere fireplaces also supply heat, sufficient for a comfortable level of heating. The device is not designed to function as a primary heat source.
Place the fireplace in a room with a minimum contents of 32m3 (WxLxH of the room). Make sure the room in which the fire is installed has sufficient ventilation possibilities. For the Serra/Corato this is 100cm2, it may spread over several vents. The stove Riano is designed to be used in combination with surrounds Baza, Elda and Adra.
Before using the fire, carefully remove the protective film of the insert and the stainless steel burner.
Warranty: The warranty on this product is 2 years. Any changes on the surface or inside of the ceramic burner, due to the usage of the product, are not included in the warranty of the ceramic burner. Ruby Fires reserves the right to make any technical alterations in order to improve the pro- duct and its characteristics / safety. Ruby Fires would like to thank you for the purchase of the ceramic burner. If all the instructi- ons are carefully followed, the ceramic burner will burn free of soot and scent.
Intro

Installation Serra & Corato:

Installation in the surround:
Make sure the fire is levelled horizontally and that the back of the fire is placed parallel to the wall behind it (vertically). Due to the production of heat around the fire, the backwall can change in colour over time.
Installation of the glass screens: The glass screens should be mounted on the burner. To do this please use the enclosed conectors + bolts. This will prevent the airflow pushing against the back wall. It is also used to control the slide on top of the burner. With two hands you can move the slide forwards and backwards. If the flames are still striking against the back wall please close the burner and contact your dealer



Use: Bio-ethanol fireplaces are easy to use. Before lighting ensure that the burner is filled to the MAX indication which is attached on the inside of the burner, with the original Ruby Fires bio-ethanol. Using a different brand or type of bio-ethanol fuel can lead to a different fire be- havior, such as increased consumption, higher temperatures and higher flames. Use approved grades of bioethanol fuel only. This fire burns appr. 3 hours on 1 liter of bioethanol. Place the burner in the insert of the fireplace with the glass facing outwards.
Light the fuel with a long match or preferably with a long lighter, with a minimum length 140mm. Note: Bio-ethanol which is at room temperature will light easier than cold fuel. Afer ignition, it may take some time before you see yellow flames, this can take up to 10 minutes. Filling the ceramic burner with Ruby Fires bio-ethanol
When the ceramic burner is filled for the first time, the ceramic element on the inside will be saturated completely. The liquid will always remain partly absorbed by the brick.






Problem Possible cause Solution
Existence of soot Wrong fuel (e.g. gel) Use ONLY Ruby Fires bio- ethanol 98%
Duration of fire too short Wrong fuel (e.g. gel) Use ONLY Ruby Fires bio- ethanol
Duration of fire too short Burner has not been filled completely
Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill.
Flames too high Wrong fuel (e.g. gel) Use ONLY Ruby Fires bio- ethanol
Flames too low, not visible Burner has not been filled completely
Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill.
Flames are blue, not visible Fuel is almost finished Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill.
Flames remain after the latch has been closed
Open the latch and quickly close it again to refrain the oxygen supply


We hope you enjoy your bio-ethanol fireplace.
This manual is part of the device and must be kept with the fire. In the case of sales to a third party the manual must be included.
In case of improper use or failure to follow the safety instructions, neither liability nor warranty will apply.
Version July 2013


Kamine

Kamine

Einsatz
Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.
Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| Existence of soot | Wrong fuel (e.g. gel) | Use ONLY Ruby Fires bio- ethanol 98% | p.5 |
| Duration of fire too short | Wrong fuel (e.g. gel) | Use ONLY Ruby Fires bio- ethanol | p.5 |
| Duration of fire too short | Burner has not been filled completely | Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill. | p.5 |
| Flames too high | Wrong fuel (e.g. gel) | Use ONLY Ruby Fires bio- ethanol | p.5 |
| Flames too low, not visible | Burner has not been filled completely | Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill. | p.5 |
| Flames are blue, not visible | Fuel is almost finished | Extinguish the burner. Let it cool down for at least 45 minutes and then re-fill. | p.5 |
| Flames remain after the latch has been closed | Open the latch and quickly close it again to refrain the oxygen supply | p.5 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.