FR
Progress logo
Notice d'utilisation officielle

Progress PKT1241

60 pages·3.4 MB·Réfrigération et congélation·PDF·ENITJA
Progress PKT1241
Table des matières 11 sections CONTENTS · SAFETY INFORMATION · OPERATION · FIRST USE · … AfficherMasquer
Page 3 of the Progress PKT1241 user manual — DAILY USE
Page 3 · cliquer pour agrandir
Page 3
  • This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used.

refuse and rubbish. The insulation foam contains flammable gases: the appli- ance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid dam- aging the cooling unit, especially at the rear near the heat exchanger. The ma- terials used on this appliance marked by the symbol are recyclable.

This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insula- tion materials. The appliance shall not be discarded together with the urban

OPERATION

Switching on Insert the plug into the wall socket. Turn the Temperature regulator clockwise to a medium setting.

A medium setting is generally the most suitable.

  • However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on:
  • room temperature
  • how often the door is opened
  • the quantity of food stored
  • the location of the appliance.

Switching off To turn off the appliance, turn the Tempera- ture regulator to the "O" position.

  • Temperature regulation The temperature is automatically regulated. To operate the appliance, proceed as follows:
  • turn the Temperature regulator toward lower settings to obtain the minimum coldness.
  • turn the Temperature regulator toward higher settings to obtain the maximum coldness.

FIRST USE

Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accesso- ries with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.

DAILY USE

Freezing fresh food The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time. To freeze fresh foods it is not necessary to change the medium setting. However, for a faster freezing operation, turn the temperature regulator toward high- er settings to obtain the maximum cold- ness.

Storage of frozen food When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings.

Environment Protection

Page 4 of the Progress PKT1241 user manual — OPERATION
Page 4 · cliquer pour agrandir
Page 4
Progress PKT1241 — OPERATION diagram (page 4)
Fig. 1

Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

The symbols show different types of frozen goods. The numbers indicate storage times in months for the appropriate types of frozen goods. Whether the upper or lower value of the indicated storage time is valid depends on the quality of the foods and treating be- fore freezing.

Progress PKT1241 — OPERATION diagram (page 4)
Fig. 2

Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, de- pending on the time available for this opera- tion. Small pieces may even be cooked still fro- zen, directly from the freezer: in this case, cooking will take longer.

Positioning the door shelves To permit storage of food packages of vari- ous sizes, the door shelves can be placed at different heights. To make these adjustments proceed as fol- lows: gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.

Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment.

Frozen Food Calendar

Page 5 of the Progress PKT1241 user manual — HELPFUL HINTS AND TIPS
Page 5 · cliquer pour agrandir
Page 5

HELPFUL HINTS AND TIPS

  • Hints for energy saving
  • Do not open the door frequently or leave it open longer than absolutely necessary.
  • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.

Fruit and vegetables: these should be thor- oughly cleaned and placed in the special drawer(s) provided. Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigera- tor.

  • Hints for fresh food refrigeration To obtain the best performance:
  • do not store warm food or evaporating liquids in the refrigerator
  • do cover or wrap the food, particularly if it has a strong flavour
  • position food so that air can circulate freely around it
  • Hints for freezing To help you make the most of the freezing process, here are some important hints:
  • the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate;
  • the freezing process takes 24 hours. No further food to be frozen should be added during this period;
  • only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
  • prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
  • wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
Page 6 of the Progress PKT1241 user manual — CARE AND CLEANING
Page 6 · cliquer pour agrandir
Page 6
  • do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
  • lean foods store better and longer than fatty ones; salt reduces the storage life of food;
  • water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
  • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.
  • make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
  • be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time;
  • not open the door frequently or leave it open longer than absolutely necessary;
  • once defrosted, food deteriorates rapidly and cannot be refrozen;
  • do not exceed the storage period indicated by the food manufacturer.

CARE AND CLEANING

Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added. After cleaning, reconnect the equipment to the mains supply.

This appliance contains hydrocarbons in its cooling unit; maintenance and re- charging must therefore only be carried out by authorized technicians.

  • Periodic cleaning The equipment has to be cleaned regularly:
  • clean the inside and accessories with lukewarm water and some neutral soap.
  • regularly check the door seals and wipe clean to ensure they are clean and free from debris.
  • rinse and dry thoroughly.

Defrosting of the refrigerator Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special contain- er at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the de- frost water drain hole in the middle of the refrigerator compartment channel to pre- vent the water overflowing and dripping on- to the food inside. Use the special cleaner provided, which you will find already inser- ted into the drain hole.

Clean the condenser (black grill) and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.

Page 7 of the Progress PKT1241 user manual — WHAT TO DO IF…
Page 7 · cliquer pour agrandir
Page 7
4. When defrosting is completed, dry the interior thoroughly and refit the plug. 5. Switch on the appliance. 6. Set the temperature regulator to obtain the maximum coldness and run the appliance for two or three hours using this setting. 7. Reload the previously removed food into the compartment.
  • Periods of non-operation When the appliance is not in use for long periods, take the following precautions:
  • disconnect the appliance from electricity supply
  • remove all food
  • defrost (if foreseen) and clean the appliance and all accessories
  • leave the door/doors ajar to prevent unpleasant smells. If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure.

A certain amount of frost will always form on the freezer shelves and around the top compartment.

To remove the frost, do these steps: 1. Switch off the appliance. 2. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place. 3. Leave the door open.

WHAT TO DO IF…

Problem Possible cause Solution

The appliance does not operate. The lamp does not operate.

The appliance is switched off. Switch on the appliance.

The mains plug is not connected to the mains socket correctly.

Connect the mains plug to the mains socket correctly.

The appliance has no power. There is no voltage in the mains socket.

Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician.

Defrosting the freezer

Page 8 of the Progress PKT1241 user manual — WHAT TO DO IF…
Page 8 · cliquer pour agrandir
Page 8

Problem Possible cause Solution

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor oper- ates continually.

The temperature is not set cor- rectly.

Set a higher temperature.

The door is not closed correctly. Refer to "Closing the door".

The door has been opened too frequently.

Do not keep the door open longer than necessary.

The product temperature is too high.

Let the product temperature de- crease to room temperature be- fore storage.

The room temperature is too high.

Decrease the room temperature.

Water flows on the rear plate of the refrigerator.

During the automatic defrosting process, frost defrosts on the rear plate.

This is correct.

Water flows into the re- frigerator.

The water outlet is clogged. Clean the water outlet.

Products prevent that water flows into the water collector.

Make sure that products do not touch the rear plate.

Water flows on the ground.

The melting water outlet does not flow in the evaporative tray above the compressor.

Attach the melting water outlet to the evaporative tray.

The temperature in the appliance is too low/ high.

The temperature regulator is not set correctly.

Set a higher/lower temperature.

The temperature in the refrigerator is too high.

There is no cold air circulation in the appliance.

Make sure that there is cold air circulation in the appliance.

The temperature in the freezer is too high.

Products are too near to each other.

Store products so that there is cold air circulation.

There is too much frost. Food is not wrapped correctly. Wrap the food correctly.

The door is not closed correctly. Refer to "Closing the door".

The temperature regulator is not set correctly.

Set a higher temperature.

Replacing the lamp 1. Remove the screw from the lamp cov- er. 2. Remove the lamp cover (refer to the il- lustration). 3. Replace the used lamp with a new lamp of the same power and specifical- ly designed for household appliances. (the maximum power is shown on the lamp cover). 4. Install the lamp cover. 5. Tighten the screw to the lamp cover. 6. Connect the mains plug to the mains socket. 7. Open the door. Make sure that the lamp comes on.

Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation".

Page 9 of the Progress PKT1241 user manual — INSTALLATION
Page 9 · cliquer pour agrandir
Page 9
3. If necessary, replace the defective door gaskets. Contact the Service Center.

TECHNICAL DATA

Dimension of the recess

Rising Time 20 h

The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.

INSTALLATION

Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.

This appliance complies with the E.E.C. Di- rectives.

Door reversibility The door of the appliance opens to the right. If you want to open the door to the left, do these steps before you install the appliance: 1. Loosen and remove the upper pin. 2. Remove the upper door. 3. Remove the spacer. 4. Loosen the middle hinge. 5. Remove the lower door. 6. Loosen and remove the lower pin.

Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power sup- ply socket is not earthed, connect the appli- ance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not ob- served.

Show 8 more labels / short text on this page
Height 1225 mm · Width 560 mm · Depth 550 mm · Voltage 230-240 V · Frequency 50 Hz · Climate · Ambient temperature · class
Page 10 of the Progress PKT1241 user manual — TECHNICAL DATA
Page 10 · cliquer pour agrandir
Page 10
Progress PKT1241 — TECHNICAL DATA diagram (page 10)
Fig. 3
Progress PKT1241 — TECHNICAL DATA diagram (page 10)
Fig. 4

On the opposite side: 1. Tighten the lower pin. 2. Install the lower door. 3. Tighten the middle hinge. 4. Install the spacer. 5. Install the upper door. Tighten the upper pin.

Do these steps. 1. If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure.

Progress PKT1241 — TECHNICAL DATA diagram (page 10)
Fig. 5
Progress PKT1241 — TECHNICAL DATA diagram (page 10)
Fig. 6

Ventilation requirements The airflow behind the appliance must be sufficient.

Installing the appliance

Page 11 of the Progress PKT1241 user manual — TECHNICAL DATA
Page 11 · cliquer pour agrandir
Page 11
2. Install the appliance in the niche. Push the appliance in the direction of the arrow (1) until the upper gap cover stops against the kitchen furniture. Make sure that the distance between the appliance and the cupboard frontedge is 44 mm. Push the appliance in the direction of the arrow (2) against the cupboard on the opposite side of the hinge. Make sure that the clearance between the appliance and the cupboard is 4 mm.
3. Adjust the appliance in the niche. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Open the door. Put the lower hinge cover in position.
Progress PKT1241 — TECHNICAL DATA diagram (page 11)
Fig. 7
Progress PKT1241 — TECHNICAL DATA diagram (page 11)
Fig. 8
4. Attach the appliance to the niche with 4 screws.
Progress PKT1241 — TECHNICAL DATA diagram (page 11)
Fig. 9
Page 12 of the Progress PKT1241 user manual — TECHNICAL DATA
Page 12 · cliquer pour agrandir
Page 12
5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case.
7. Disconnect the parts (Ha), (Hb), (Hc) and (Hd).
Progress PKT1241 — TECHNICAL DATA diagram (page 12)
Fig. 10
Progress PKT1241 — TECHNICAL DATA diagram (page 12)
Fig. 11
8. Install the part (Ha) on the inner side of the kitchen furniture.
6. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge.
Progress PKT1241 — TECHNICAL DATA diagram (page 12)
Fig. 12
Progress PKT1241 — TECHNICAL DATA diagram (page 12)
Fig. 13
9. Push the part (Hc) on the part (Ha).
Progress PKT1241 — TECHNICAL DATA diagram (page 12)
Fig. 14
Page 13 of the Progress PKT1241 user manual — ENVIRONMENTAL CONCERNS
Page 13 · cliquer pour agrandir
Page 13
10. Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes.
12. Place the small square on the guide again and fix it with the screws supplied. Align the kitchen furniture door and the appliance door by adjusting the part (Hb).
Progress PKT1241 — ENVIRONMENTAL CONCERNS diagram (page 13)
Fig. 15
Progress PKT1241 — ENVIRONMENTAL CONCERNS diagram (page 13)
Fig. 16
11. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K).
13. Press the part (Hd) on the part (Hb).
Progress PKT1241 — ENVIRONMENTAL CONCERNS diagram (page 13)
Fig. 17
Progress PKT1241 — ENVIRONMENTAL CONCERNS diagram (page 13)
Fig. 18
  • Do a final check to make sure that:
  • All screws are tightened.
  • The sealing strip is attached tightly to the cabinet.
  • The door opens and closes correctly.

ENVIRONMENTAL CONCERNS

product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this

Ha

Page 14 of the Progress PKT1241 user manual — ENVIRONMENTAL CONCERNS
Page 14 · cliquer pour agrandir
Page 14

contact your local council, your household waste disposal service or the shop where you purchased the product.

Dépannage

Dépannage

Problèmes fréquents, causes probables et solutions.

ProblèmeCause possibleSolution
The appliance does not operate. The lamp does not operate.The appliance is switched off.Switch on the appliance. p.7
The appliance does not operate. The lamp does not operate.The mains plug is not connected to the mains socket correctly.Connect the mains plug to the mains socket correctly. p.7
The appliance does not operate. The lamp does not operate.The appliance has no power. There is no voltage in the mains socket.Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician. p.7
The lamp does not work.The lamp is in stand-by.Close and open the door. p.8
The lamp does not work.The lamp is defective.Refer to "Replacing the lamp". p.8
The compressor oper- ates continually.The temperature is not set cor- rectly.Set a higher temperature. p.8
The compressor oper- ates continually.The door is not closed correctly.Refer to "Closing the door". p.8
The compressor oper- ates continually.The door has been opened too frequently.Do not keep the door open longer than necessary. p.8
The compressor oper- ates continually.The product temperature is too high.Let the product temperature de- crease to room temperature be- fore storage. p.8
The compressor oper- ates continually.The room temperature is too high.Decrease the room temperature. p.8
Water flows on the rear plate of the refrigerator.During the automatic defrosting process, frost defrosts on the rear plate.This is correct. p.8
Water flows into the re- frigerator.The water outlet is clogged.Clean the water outlet. p.8
Water flows into the re- frigerator.Products prevent that water flows into the water collector.Make sure that products do not touch the rear plate. p.8
Water flows on the ground.The melting water outlet does not flow in the evaporative tray above the compressor.Attach the melting water outlet to the evaporative tray. p.8
The temperature in the appliance is too low/ high.The temperature regulator is not set correctly.Set a higher/lower temperature. p.8
The temperature in the refrigerator is too high.There is no cold air circulation in the appliance.Make sure that there is cold air circulation in the appliance. p.8
The temperature in the freezer is too high.Products are too near to each other.Store products so that there is cold air circulation. p.8
There is too much frost.Food is not wrapped correctly.Wrap the food correctly. p.8
There is too much frost.The door is not closed correctly.Refer to "Closing the door". p.8
There is too much frost.The temperature regulator is not set correctly.Set a higher temperature. p.8

Poser une question sur : Progress PKT1241

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Progress PKT1241

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Progress PKT1241 manuel PDF

60 pages·3.4 MB·Réfrigération et congélation·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…