

in either its refrigerant circuit or insula- tion materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appli- ance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid dam- aging the cooling unit, especially at the rear near the heat exchanger. The ma- terials used on this appliance marked by the symbol are recyclable.
This appliance does not contain gasses which could damage the ozone layer,
Switching on Insert the plug into the wall socket. Turn the Temperature regulator clockwise to a medium setting.
A medium setting is generally the most suitable.
Switching off To turn off the appliance, turn the Tempera- ture regulator to the "O" position.
Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accesso- ries with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.
Freezing fresh food The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.
To freeze fresh foods it is not necessary to change the medium setting. However, for a faster freezing operation, turn the temperature regulator toward high-
Environment Protection

er settings to obtain the maximum cold- ness.
failure, if the power has been off for longer that the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after cooling).
Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, de- pending on the time available for this opera- tion. Small pieces may even be cooked still fro- zen, directly from the freezer: in this case, cooking will take longer.
Place the fresh food to be frozen on the bottom compartment.
Storage of frozen food When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings. If large quantities of food are to be stored, remove all drawers and baskets from appli- ance and place food on cooling shelves to obtain the best performance.
Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment.
The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.
Temperature Indicator · Movable shelves

Positioning the door shelves
To permit storage of food packages of vari- ous sizes, the door shelves can be placed at different heights. To make these adjustments proceed as fol- lows: gradually pull the shelf in the direction of the arrows until it comes free, then reposi- tion as required.
Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigera- tor.
Hints for refrigeration Useful hints: Meat (all types) : wrap in polythene bags and place on the glass shelf above the veg- etable drawer. For safety, store in this way only one or two days at the most. Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf. Fruit and vegetables: these should be thor- oughly cleaned and placed in the special drawer(s) provided.

polishes to clean the interior as this will damage the surface and leave a strong odour.
This appliance contains hydrocarbons in its cooling unit; maintenance and re- charging must therefore only be carried out by authorized technicians.
Clean the condenser (black grill) and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added. After cleaning, reconnect the equipment to the mains supply.
Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a drain hole into a special con- tainer at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the de- frost water drain hole in the middle of the refrigerator compartment channel to pre- vent the water overflowing and dripping on- to the food inside.
Defrosting the refrigerator

Defrosting the freezer A certain amount of frost will always form on the freezer shelves and around the top compartment. Defrost the freezer when the frost layer rea- ches a thickness of about 3-5 mm.
To remove the frost, follow the instructions below: 1. Switch off the appliance. 2. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place.
In order to speed up the defrosting process, place a pot of warm water in the freezer compartment. In addition, remove pieces of ice that break away before defrosting is complete. 4. When defrosting is completed, dry the interior thoroughly and keep the scra- per for future use. 5. Switch on the appliance. 6. After two or three hours, reload the previously removed food into the com- partment.
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any arti- ficial means to speed up the thawing proc- ess other than those recommended by the manufacturer. A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life.

the food inside from spoiling in case of a power failure.
Problem Possible cause Solution
The appliance does not operate. The lamp does not operate.
The appliance is switched off. Switch on the appliance.
The mains plug is not connected to the mains socket correctly.
Connect the mains plug to the mains socket correctly.
The appliance has no power. There is no voltage in the mains socket.
Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician.
The lamp does not work. The lamp is in stand-by. Close and open the door.
The lamp is defective. Refer to "Replacing the lamp".
The compressor oper- ates continually.
The temperature is not set cor- rectly.
Set a higher temperature.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too frequently.
Do not keep the door open longer than necessary.
The product temperature is too high.
Let the product temperature de- crease to room temperature be- fore storage.
The room temperature is too high.
Decrease the room temperature.
Water flows on the rear plate of the refrigerator.
During the automatic defrosting process, frost defrosts on the rear plate.
This is correct.
Water flows into the re- frigerator.
The water outlet is clogged. Clean the water outlet.
Products prevent that water flows into the water collector.
Make sure that products do not touch the rear plate.
Water flows on the ground.
The melting water outlet does not flow in the evaporative tray above the compressor.
Attach the melting water outlet to the evaporative tray.
The temperature in the appliance is too low/ high.
The temperature regulator is not set correctly.
Set a higher/lower temperature.
The temperature in the refrigerator is too high.
There is no cold air circulation in the appliance.
Make sure that there is cold air circulation in the appliance.
The temperature in the freezer is too high.
Products are too near to each other.
Store products so that there is cold air circulation.
There is too much frost. Food is not wrapped correctly. Wrap the food correctly.

Problem Possible cause Solution
The door is not closed correctly. Refer to "Closing the door".
The temperature regulator is not set correctly.
Set a higher temperature.

1. Disconnect the mains plug from the mains socket. 2. Remove the screw from the lamp cov- er. 3. Remove the lamp cover (refer to the il- lustration). 4. Replace the used lamp with a new lamp of the same power and specifical- ly designed for household appliances. (the maximum power is shown on the lamp cover). 5. Install the lamp cover. 6. Tighten the screw to the lamp cover. 7. Connect the mains plug to the mains socket. 8. Open the door. Make sure that the lamp comes on.
Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation".

The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.
Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:
Replacing the lamp


for this purpose. If the domestic power sup- ply socket is not earthed, connect the appli- ance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not ob- served. This appliance complies with the E.E.C. Di- rectives.
Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact

Door reversibility


The airflow behind the appliance must be sufficient.
Do these steps.

If necessary cut the adhesive sealing strip and apply it to the appliance as shown in figure.
Install the appliance in the niche. Push the appliance in the direction of the ar- row (1) until the upper gap cover stops against the kitchen furniture. Push the appliance in the direction of the ar- row (2) against the cupboard on the oppo- site side of the hinge.
Ventilation requirements · Installing the appliance


Adjust the appliance in the niche. Make sure that the distance between the appliance and the cupboard front-edge is 44 mm. The plastic spacer (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is cor- rect. Make sure that the clearance between the appliance and the cupboard is 4 mm. Open the door. Put the plastic spacer in po- sition.
Attach the appliance to the niche with 4 screws.
Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case.


Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge.
Connect the appliance laterally to the kitch- en furniture sidewall: 1. Loosen the screws of the part (G) and move the part (G) till the furniture side- wall. 2. Tighten the screws of the part (G) again. 3. Attach the part (H) to the part (G).
Disconnect the parts (Ha), (Hb), (Hc) and (Hd).


Install the part (Ha) on the inner side of the kitchen furniture.
Push the part (Hc) on the part (Ha).
8 mm Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the fur- niture door and mark the holes.

8 mm Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K).
Place the small square on the guide again and fix it with the screws supplied. Align the kitchen furniture door and the ap- pliance door by adjusting the part (Hb).
Press the part (Hd) on the part (Hb).
collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate

consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please
contact your local council, your household waste disposal service or the shop where you purchased the product.
Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| The appliance does not operate. The lamp does not operate. | The appliance is switched off. | Switch on the appliance. | p.8 |
| The appliance does not operate. The lamp does not operate. | The mains plug is not connected to the mains socket correctly. | Connect the mains plug to the mains socket correctly. | p.8 |
| The appliance does not operate. The lamp does not operate. | The appliance has no power. There is no voltage in the mains socket. | Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician. | p.8 |
| The lamp does not work. | The lamp is in stand-by. | Close and open the door. | p.8 |
| The lamp does not work. | The lamp is defective. | Refer to "Replacing the lamp". | p.8 |
| The compressor oper- ates continually. | The temperature is not set cor- rectly. | Set a higher temperature. | p.8 |
| The compressor oper- ates continually. | The door is not closed correctly. | Refer to "Closing the door". | p.8 |
| The compressor oper- ates continually. | The door has been opened too frequently. | Do not keep the door open longer than necessary. | p.8 |
| The compressor oper- ates continually. | The product temperature is too high. | Let the product temperature de- crease to room temperature be- fore storage. | p.8 |
| The compressor oper- ates continually. | The room temperature is too high. | Decrease the room temperature. | p.8 |
| Water flows on the rear plate of the refrigerator. | During the automatic defrosting process, frost defrosts on the rear plate. | This is correct. | p.8 |
| Water flows into the re- frigerator. | The water outlet is clogged. | Clean the water outlet. | p.8 |
| Water flows into the re- frigerator. | Products prevent that water flows into the water collector. | Make sure that products do not touch the rear plate. | p.8 |
| Water flows on the ground. | The melting water outlet does not flow in the evaporative tray above the compressor. | Attach the melting water outlet to the evaporative tray. | p.8 |
| The temperature in the appliance is too low/ high. | The temperature regulator is not set correctly. | Set a higher/lower temperature. | p.8 |
| The temperature in the refrigerator is too high. | There is no cold air circulation in the appliance. | Make sure that there is cold air circulation in the appliance. | p.8 |
| The temperature in the freezer is too high. | Products are too near to each other. | Store products so that there is cold air circulation. | p.8 |
| There is too much frost. | Food is not wrapped correctly. | Wrap the food correctly. | p.8 |
| The door is not closed correctly. | Refer to "Closing the door". | p.9 | |
| The temperature regulator is not set correctly. | Set a higher temperature. | p.9 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.