FR
Progress logo
Notice d'utilisation officielle

Progress PK1244

56 pages·1.3 MB·Réfrigération et congélation·PDF·ENITJA
Progress PK1244
Table des matières 48 sections CONTENTS · SAFETY INFORMATION · Children and vulnerable people safety · General Safety · … AfficherMasquer
Page 2 of the Progress PK1244 user manual — Electrical connection
Page 2 · cliquer pour agrandir
Page 2
  • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
  • Do not damage the refrigerant circuit.
  • Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
  • Do not use water spray and steam to clean the appliance.
  • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.

SAFETY INSTRUCTIONS

Installation

  • Do not install this appliance in areas that are too humid or too colds, such as the construction appendices, garages or wine cellars.
  • When you move the appliance, lift it by the front edge to avoid scratching the floor.
  • Remove all the packaging and the transit bolts.
  • Do not install or use a damaged appliance.
  • Follow the installation instruction supplied with the appliance.
  • Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.
  • Make sure the air can circulate around the appliance.
  • Wait at least 4 hours before connecting the appliance to the power supply. This is to allow the oil to flow back in the compressor.
  • Do not install the appliance close to radiators or cookers, oven or hobs.
  • The rear of the appliance must stand against the wall.
  • Do not install the appliance where there is direct sunlight.

Electrical connection

  • The appliance must be earthed.
  • Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
  • Always use a correctly installed shockproof socket.
  • Do not use multi-plug adapters and extension cables.
  • Make sure not to cause damage to the electrical components (e.g. mains plug, mains cable, compressor). Contact the Authorised Service Centre or an
Page 3 of the Progress PK1244 user manual — Disposal
Page 3 · cliquer pour agrandir
Page 3
  • electrician to change the electrical components.
  • The mains cable must stay below the level of the mains plug.
  • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
  • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
  • Obey the storage instructions on the packaging of frozen food.

Internal light

  • The type of lamp used for this appliance is not suitable for household room illumination

Care and cleaning

Use

  • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
  • This appliance contains hydrocarbons in the cooling unit. Only a qualified person must do the maintenance and the recharging of the unit.
  • Regularly examine the drain of the appliance and if necessary, clean it. If the drain is blocked, defrosted water collects in the bottom of the appliance.
  • Do not change the specification of this appliance.
  • Do not put electrical appliances (e.g. ice cream makers) in the appliance unless they are stated applicable by the manufacturer.
  • Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a natural gas with a high level of environmental compatibility. This gas is flammable.
  • If damage occurs to the refrigerant circuit, make sure that there are no flames and sources of ignition in the room. Ventilate the room.
  • Do not let hot items to touch the plastic parts of the appliance.
  • Do not put soft drinks in the freezer compartment. This will create pressure on the drink container.
  • Do not store flammable gas and liquid in the appliance.
  • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
  • Do not touch the compressor or the condenser. They are hot.
  • Do not remove or touch items from the freezer compartment if your hands are wet or damp.
  • Do not freeze again food that has been thawed.

Disposal

  • Disconnect the appliance from the mains supply.
  • Cut off the mains cable and discard it.
  • Remove the door to prevent children and pets to be closed inside of the appliance.
  • The refrigerant circuit and the insulation materials of this appliance are ozonefriendly.
  • The insulation foam contains flammable gas. Contact your municipal authority for information on how to discard the appliance correctly.
  • Do not cause damage to the part of the cooling unit that is near the heat exchanger.
Page 4 of the Progress PK1244 user manual — Thawing
Page 4 · cliquer pour agrandir
Page 4

OPERATION

Switching on

1. Turn the Temperature regulator toward lower settings to obtain the minimum coldness. 2. Turn the Temperature regulator toward higher settings to obtain the maximum coldness.
1. Insert the plug into the wall socket. 2. Turn the Temperature regulator clockwise to a medium setting.

Switching off

To turn off the appliance, turn the temperature regulator to the "O" position.

Temperature regulation

The temperature is regulated automatically.

  • A medium setting is generally the most suitable. However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on:
  • room temperature,
  • how often the door is opened,
  • the quantity of food stored,
  • the location of the appliance.

DAILY USE

Storage of frozen food

When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings.

Freezing fresh food

The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.

In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer than the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after cooling).

To freeze fresh foods it is not necessary to change the medium setting.

However, for a faster freezing operation, turn the temperature regulator toward higher settings to obtain the maximum coldness.

Thawing

Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature,

Page 5 of the Progress PK1244 user manual — Normal operating sounds
Page 5 · cliquer pour agrandir
Page 5

depending on the time available for this operation.

Do not move the glass shelf above the vegetable drawer to ensure correct air circulation.

Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer.

Ice-cube production

Positioning the door shelves

This appliance is equipped with one or more trays for the production of ice-cubes.

To permit storage of food packages of various sizes, the door shelves can be placed at different heights.

Do not use metallic instruments to remove the trays from the freezer.

1. Gradually pull the shelf in the direction of the arrows until it comes free. 2. Reposition as required.
1. Fill these trays with water 2. Put the ice trays in the freezer compartment.

Temperature indicator

For proper storage of food the refrigerator is equipped with the temperature indicator. The symbol on the side wall of the appliance indicates the coldest area in the refrigerator.

If OK is displayed (A), put fresh food into area indicated by symbol, if not (B), adjust the temperature controller to a colder setting and wait 12 hours before checking the temperature indicator again.

Movable shelves

The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

A

OK

B

OK

After putting fresh food into the appliance or after opening the door repeatedly or for a long period, it is normal for the indicator not to show OK; wait at least 12 hours before readjusting the temperature controller.

HINTS AND TIPS

Normal operating sounds

  • A faint gurgling and bubbling sound from coils sound when refrigerant is pumped.

The following sounds are normal during operation:

Page 6 of the Progress PK1244 user manual — Hints for storage of frozen food
Page 6 · cliquer pour agrandir
Page 6
  • A whirring and pulsating sound from the compressor when refrigerant is pumped.
  • A sudden cracking noise from inside appliance caused by thermic dilatation (a natural and not dangerous physical phenomenon).
  • A faint click noise from the temperature regulator when the compressor switches on or off.
  • Bottles: close with a cap and place on the door bottle shelf, or (if available) on the bottle rack.

Hints for freezing

To help you make the most of the freezing process, here are some important hints:

  • the maximum quantity of food which can be frozen in 24 hours is shown on the rating plate;
  • the freezing process takes 24 hours no further food to be frozen should be added during this period;
  • freeze only top quality, fresh and thoroughly cleaned, foodstuffs;
  • prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
  • wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
  • do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
  • lean foods store better and longer than fatty ones; salt reduces the storage life of food;
  • water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
  • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.

Hints for energy saving

  • Do not open the door frequently or leave it open longer than absolutely necessary.
  • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.

Hints for fresh food refrigeration

To obtain the best performance:

  • do not store warm food or evaporating liquids in the refrigerator
  • do cover or wrap the food, particularly if it has a strong flavour
  • position food so that air can circulate freely around it

Hints for refrigeration

Useful hints:

  • Meat (all types): wrap in a suitable packaging and place it on the glass shelf above the vegetable drawer. Store meat for at most 1-2 days.
  • Cooked foods, cold dishes: cover and place on any shelf.
  • Fruit and vegetables: clean thoroughly and place in a special drawer. Bananas, potatoes, onions and garlic must not be kept in the refrigerator if not packed.
  • Butter and cheese: place in a special airtight container or wrap in an aluminium foil or a polythene bag to exclude as much air as possible.

Hints for storage of frozen food

To obtain the best performance from this appliance, you should:

  • make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
  • be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time;
  • not open the door frequently or leave it open longer than absolutely necessary;
  • once defrosted, food deteriorates rapidly and cannot be refrozen;
Page 7 of the Progress PK1244 user manual — Periodic cleaning
Page 7 · cliquer pour agrandir
Page 7
  • do not exceed the storage period indicated by the food manufacturer.

CARE AND CLEANING

1. Clean the inside and accessories with lukewarm water and some neutral soap. 2. Regularly check the door seals and wipe clean to ensure they are clean and free from debris. 3. Rinse and dry thoroughly. 4. If accessible, clean the condenser and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.

General warnings

This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.

Defrosting of the refrigerator

Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.

The accessories and parts of the appliance are not suitable for washing in a dishwasher.

Cleaning the interior

Before using the appliance for the first time, the interior and all internal accessories should be washed with lukewarm water and some neutral soap to remove the typical smell of a brand-new product, then dried thoroughly.

It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside.

Periodic cleaning

The equipment has to be cleaned regularly:

Page 8 of the Progress PK1244 user manual — TROUBLESHOOTING
Page 8 · cliquer pour agrandir
Page 8

Defrosting the freezer

3. Leave the door open. In order to speed up the defrosting process, place a pot of warm water in the freezer compartment. In addition, remove pieces of ice that break away before defrosting is complete. 4. When defrosting is completed, dry the interior thoroughly. 5. Switch on the appliance. After three hours reload the previously removed food into the freezer compartment.

Periods of non-operation

About 12 hours prior to defrosting, set a lower temperature, in order to build up sufficient chill reserve for the interruption in operation.

When the appliance is not in use for long periods, take the following precautions:

1. Disconnect the appliance from electricity supply. 2. Remove all food. 3. Defrost (if necessary) and clean the appliance and all accessories. 4. Clean the appliance and all accessories. 5. Leave the door/doors open to prevent unpleasant smells.

A certain amount of frost will always form on the freezer shelves and around the top compartment.

Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.

1. Switch off the appliance, or pull out electrical plug from the wall socket. 2. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place.

TROUBLESHOOTING

What to do if...

Problem Possible cause Solution

The appliance does not oper- ate.

The appliance is switched off. Switch on the appliance.

Page 9 of the Progress PK1244 user manual — Defrosting the freezer
Page 9 · cliquer pour agrandir
Page 9

Problem Possible cause Solution

The mains plug is not con- nected to the mains socket correctly.

Connect the mains plug to the mains socket correctly.

There is no voltage in the mains socket.

Connect a different electrical appliance to the mains sock- et. Contact a qualified electri- cian.

The appliance is noisy. The appliance is not suppor- ted properly.

Check if the appliance stands stable.

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor operates continually.

Temperature is set incorrect- ly.

Refer to "Operation" chapter.

Many food products to be frozen were put in at the same time.

Wait a few hours and then check the temperature again.

The room temperature is too high.

Refer to climate class chart on the rating plate.

Food products placed in the appliance were too warm.

Allow food products to cool to room temperature before storing.

There is too much frost and ice.

The door is not closed cor- rectly or the gasket is de- formed/dirty.

Refer to "Closing the door".

The water drainage plug is not correctly positioned.

Position the water drainage plug in the correct way.

Food products are not wrap- ped properly.

Wrap the food products bet- ter.

Temperature is set incorrect- ly.

Refer to "Operation" chapter.

Water flows on the rear plate of the refrigerator.

During the automatic defrost- ing process, frost melts on the rear plate.

This is correct.

Water flows into the refrigera- tor.

The water outlet is clogged. Clean the water outlet.

Food products prevent that water flows into the water collector.

Make sure that food prod- ucts do not touch the rear plate.

Page 10 of the Progress PK1244 user manual — Replacing the lamp
Page 10 · cliquer pour agrandir
Page 10

Problem Possible cause Solution

Water flows on the floor. The melting water outlet is not connected to the evapo- rative tray above the com- pressor.

Attach the melting water out- let to the evaporative tray.

The temperature in the appli- ance is too low/too high.

The temperature regulator is not set correctly.

Set a higher/lower tempera- ture.

The door is not closed cor- rectly.

Refer to "Closing the door".

The food products' tempera- ture is too high.

Let the food products tem- perature decrease to room temperature before storage.

Many food products are stor- ed at the same time.

Store less food products at the same time.

The thickness of the frost is greater than 4-5 mm.

Defrost the appliance.

The door has been opened often.

Open the door only if neces- sary.

There is too much con- densed water on the rear wall of the refrigerator.

Door was opened too fre- quently.

Open the door only when necessary.

Door was not closed com- pletely.

Make sure the door is closed completely.

Stored food was not wrap- ped.

Wrap food in suitable pack- aging before storing it in the appliance.

Door does not open easily. You attempted to re-open the door immediately after closing.

Wait a few seconds between closing and re-opening of the door.

1. At the same time, with the fingers expand up and down the transparent cover and unhook it in the direction of the arrows.

If the advice does not lead to the desired result, call the nearest Authorized Service Centre.

Replacing the lamp

The appliance is equipped with a longlife LED interior light.

Page 11 of the Progress PK1244 user manual — Positioning
Page 11 · cliquer pour agrandir
Page 11
Progress PK1244 — Closing the door diagram (page 11)
Fig. 1 · Closing the door

for household appliances. The maximum power is shown on the light bulb cover. 3. Reassemble the lamp cover. 4. Connect the plug to the mains socket. 5. Open the door. Make sure that the light comes on.

Closing the door

1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to assembly instructions. 3. If necessary, replace the defective door gaskets. Contact the Authorised Service Centre.
2. Replace the lamp with one of the same power and shape, specifically designed

INSTALLATION

Some functional problems might occur for some types of models when operating outside of that range. The correct operation can only be guaranteed within the specified temperature range. If you have any doubts regarding where to install the appliance, please turn to the vendor, to our customer service or to the nearest Authorised Service Centre.

Location

Refer to the assembly instructions for the installation.

To ensure best performance, install the appliance well away from sources of heat such as radiators, boilers, direct sunlight etc. Make sure that air can circulate freely around the back of the cabinet.

Positioning

Ventilation requirements

Install the appliance in a dry, well ventilated indoors where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance.

The airflow behind the appliance must be sufficient.

Progress PK1244 — Positioning diagram (page 11)
Fig. 2 · Positioning
Page 12 of the Progress PK1244 user manual — ENVIRONMENTAL CONCERNS
Page 12 · cliquer pour agrandir
Page 12

Electrical connection

  • separate earth in compliance with current regulations, consulting a qualified electrician.
  • The manufacturer declines all responsibility if the above safety precautions are not observed.
  • This appliance complies with the E.E.C. Directives.
  • Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.
  • The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a

TECHNICAL DATA

Technical data

Rising time Hours 12

Voltage Volts 230 - 240

The technical information is situated in the rating plate, on the external or internal side of the appliance and in the energy label.

ENVIRONMENTAL CONCERNS

dispose appliances marked with the symbol

Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not

with the household waste. Return the product to your local recycling facility or contact your municipal office.

Show 4 more labels / short text on this page
Height mm 1219 · Width mm 540 · Depth mm 550 · Frequency Hz 50
Dépannage

Dépannage

Problèmes fréquents, causes probables et solutions.

ProblèmeCause possibleSolution
The appliance does not oper- ate.The appliance is switched off.Switch on the appliance. p.8
The mains plug is not con- nected to the mains socket correctly.Connect the mains plug to the mains socket correctly. p.9
There is no voltage in the mains socket.Connect a different electrical appliance to the mains sock- et. Contact a qualified electri- cian. p.9
The appliance is noisy.The appliance is not suppor- ted properly.Check if the appliance stands stable. p.9
The lamp does not work.The lamp is in stand-by.Close and open the door. p.9
The lamp does not work.The lamp is defective.Refer to "Replacing the lamp". p.9
The compressor operates continually.Temperature is set incorrect- ly.Refer to "Operation" chapter. p.9
The compressor operates continually.Many food products to be frozen were put in at the same time.Wait a few hours and then check the temperature again. p.9
The compressor operates continually.The room temperature is too high.Refer to climate class chart on the rating plate. p.9
The compressor operates continually.Food products placed in the appliance were too warm.Allow food products to cool to room temperature before storing. p.9
There is too much frost and ice.The door is not closed cor- rectly or the gasket is de- formed/dirty.Refer to "Closing the door". p.9
There is too much frost and ice.The water drainage plug is not correctly positioned.Position the water drainage plug in the correct way. p.9
There is too much frost and ice.Food products are not wrap- ped properly.Wrap the food products bet- ter. p.9
There is too much frost and ice.Temperature is set incorrect- ly.Refer to "Operation" chapter. p.9
Water flows on the rear plate of the refrigerator.During the automatic defrost- ing process, frost melts on the rear plate.This is correct. p.9
Water flows into the refrigera- tor.The water outlet is clogged.Clean the water outlet. p.9
Water flows into the refrigera- tor.Food products prevent that water flows into the water collector.Make sure that food prod- ucts do not touch the rear plate. p.9
Water flows on the floor.The melting water outlet is not connected to the evapo- rative tray above the com- pressor.Attach the melting water out- let to the evaporative tray. p.10
The temperature in the appli- ance is too low/too high.The temperature regulator is not set correctly.Set a higher/lower tempera- ture. p.10
The temperature in the appli- ance is too low/too high.The door is not closed cor- rectly.Refer to "Closing the door". p.10
The temperature in the appli- ance is too low/too high.The food products' tempera- ture is too high.Let the food products tem- perature decrease to room temperature before storage. p.10
The temperature in the appli- ance is too low/too high.Many food products are stor- ed at the same time.Store less food products at the same time. p.10
The temperature in the appli- ance is too low/too high.The thickness of the frost is greater than 4-5 mm.Defrost the appliance. p.10
The temperature in the appli- ance is too low/too high.The door has been opened often.Open the door only if neces- sary. p.10
There is too much con- densed water on the rear wall of the refrigerator.Door was opened too fre- quently.Open the door only when necessary. p.10
There is too much con- densed water on the rear wall of the refrigerator.Door was not closed com- pletely.Make sure the door is closed completely. p.10
There is too much con- densed water on the rear wall of the refrigerator.Stored food was not wrap- ped.Wrap food in suitable pack- aging before storing it in the appliance. p.10
Door does not open easily.You attempted to re-open the door immediately after closing.Wait a few seconds between closing and re-opening of the door. p.10

Poser une question sur : Progress PK1244

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Progress PK1244

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Progress PK1244 manuel PDF

56 pages·1.3 MB·Réfrigération et congélation·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…