

Before using for the first time
Never operate the extractor hood without a grease filter. Overheated fat or oil can easily catch fire. If you are cooking with fat or oil, e.g. chips, etc., never leave the cooker unattended. Do not flambé food directly under the extractor hood.
for this operating mode (see Filters and maintenance). The complete installation set and replacement filters can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these operating instructions. q The extractor-hood fan extracts the
Risk of grease filter catching fire due ! to flames. The hotplates must always be covered with a utensil.
kitchen vapours which are purified in the grease filter and activated carbon filter and then conveyed back into the kitchen. q The grease filter absorbs the grease

time, please read these Instructions for Use carefully. They contain important information concerning your personal safety as well as on use and care of the appliance. q Please retain the operating and
particles in the kitchen vapours. q The activated carbon filter binds the
odorous substances. If no activated carbon filter is installed, it is not possible to bind the odorous substances in the cooking vapours.
installation instructions for a subsequent owner. Do not use the appliance if damaged.
kitchen vapours and conveys them through the grease filter into the atmosphere. q The grease filter absorbs the solid
Restrictions apply to the use of the extractor hood over a solid-fuel burner (coal, wood, etc.). (See Installation instructions).
particles in the kitchen vapours. q The kitchen is kept almost free of grease
and odours. D When the extractor hood is operated in exhaust-air mode simultaneously with a different burner which also makes use of the same chimney (such as gas, oil or coal-fired heaters, continuous-flow heaters, hot-water boilers) care must be taken to ensure that there is an adequate supply of fresh air which will be needed by the burner for combustion. Safe operation is possible provided that the underpressure in the room where the burner is installed does not exceed 4 Pa (0.04 mbar).
Gas hobs / Gas cookers Do not use all the gas hotplates simultaneously for a prolonged period (max. 15 minutes) at maximum thermal load, otherwise there is a risk of burns if the housing surfaces are touched or a risk of damage to the extractor hood. If the extractor hood is situated over a gas hob, operate the hood at maximum setting if three or more gas hotplates are operated simultaneously.
versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. q This extractor hood complies with all
relevant safety regulations. Repairs should be carried out by qualified technicians only. Improper repairs may put the user at considerable risk.
This can be achieved if combustion air can flow through non-lockable openings, e.g. in doors, windows and via the air- intake/exhaust-air wall box or by other technical measures, such as reciprocal interlocking, etc. If the air intake is inadequate, there is a risk of poisoning from combustion gases which are drawn back into the room. An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will not be exceeded. Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as hobs and ovens. Unrestricted operation is possible if the extractor hood is used in recirculating mode – with activated carbon filter.
The appliance is not intended for use by young children or infirmed persons without supervision. Young children should be supervised to ensure they do not play with the appliance. If the connecting cable for this appliance is damaged, the cable must be replaced by the manufacturer or his custo- mer service or a similarly qualified person in order to prevent serious injury to the user. The appliance may be connected to the mains by a qualified technician only. Dispose of packaging materials properly (see Installation instructions). This extractor hood is designed for domestic use only. Light bulbs must always be fitted when the extractor hood is in use. Defective bulbs should be replaced immediately to prevent the remaining bulbs from overloading.
If you have any questions or if a fault occurs, please call Customer Service. (See list of Customer Service representatives). When you call, please quote the following:
E-Nr. FD
Enter the relevant numbers into the box above. The E-Nr. (product no.) and FD (production date) are shown on the nameplate which can be seen inside the extractor hood after the filter frame has been detached.


The most effective method of removing vapours produced during cooking is to: q Switch the ventilator ON
Grease filters:
Metal filters are used to trap the greasy element of the vapours that develop during cooking. The filter mats are made from non- combustible metal.
as soon as you begin cooking. q Switch the ventilator OFF
Activated carbon filter: For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting.
Fan OFF Light ON / OFF
Reduce fan speed Fan ON and increase speed Intensive setting Display for fan setting
Installation and removal: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. Insert the activated carbon filter.
Switching the fan ON q Press the + button.
the metal grease filter must be cleaned 1 x a month. q The filters can be cleaned in a dish-
Setting the required fan speed: q Press the + button.
washer. It is however possible that they will become slightly discoloured. q The filter must be placed loosely, and
The fan speed is increased by one step. q Press the – button.

The fan speed is reduced by one step.
NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. q When cleaning the filters by hand, soak
Switching the fan OFF: q Press the 0 button.
switches off.
them in hot soapy water first of all. Do not use aggressive, acidic or caustic cleaners. Then brush the filters clean, rinse them thoroughly and leave the water to drain off.
Intensive setting: Maximum power is obtained at the intensive setting. It is only required for short intervals. q Keep pressing the + button until a ç
appears in the display. q If the intensive setting is not cancelled by
Removing and inserting the metal grease filters: Warning: The halogen bulbs must be switched off and cool. 1. Press the catch on the grease filters inwards and fold the filters down. At the same time take hold of the under- side of the grease filters with your other hand.
hand, the fan will automatically switch back to step } after 10 minutes. Lighting: q The light can be switched on at any
per day) the activated carbon filters should be replaced approximately 1 x year. q A replacement filter can be obtained
time, even though the fan is switched off.
from any authorized dealer (see optional accessories). q Use original filters only.

By doing so you will obtain maximum performance from your extractor hood.
Disposing of the old activated carbon filter: q There are no pollutants in the activated
carbon filters. They can therefore be disposed of as part of your normal domestic refuse.

Cleaning and care
Replacing the light bulbs
Important information
Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine! q Clean the extractor hood with a hot soap
Old appliances are not worthless rubbish. Valuable raw materials can be reclaimed by recycling old appliances. Before disposing of your old appliance, render it unusable. You received your new appliance in a protective shipping carton. All packaging materials are environmentally friendly and recyclable. Please contribute to a better environment by disposing of packaging materials in an environmentally-friendly manner. Please ask your dealer or inquire at your local authority about current means of disposal. The extractor hood can be used in exhaust air or circulating air mode. Always mount the extractor hood over the centre of the hob. Minimum distance between electric hob and bottom edge of extractor hood: 550 mm, Fig. 1. The extractor hood must not be installed over a solid fuel cooker – a potential fire hazard (e.g. flying sparks) – unless the cooker features a closed, non-removable cover and all national regulations are observed. The smaller the gap between the extractor hood and hotplates, the greater the likelihood that droplets will form on the underside of the extractor hood.
solution or a mild window cleaner. q Do not scrape off dried-on dirt but wipe
off with a damp cloth. q When cleaning the grease filters, remove
grease deposits from accessible parts of the housing. This prevents the risk of fire and ensures that the extractor hood continues operating at maximum efficiency. q Note: Do not use alcohol (spirit) on
plastic surfaces, as dull marks may appear. Caution: Ensure that the kitchen is ade- quately ventilated. Avoid naked flames! Clean the operating buttons with a mild soapy solution and a soft, damp cloth only. Do not use stainless-steel cleaner to clean the operating buttons.
cleaner. q Clean the surface in the same direction
as it has been ground and polished. q We recommend our stainless steel
cleaner no. 461731. See enclosed service booklet for order address.
Additional information concerning gas cookers: When installing gas hotplates, comply with the relevant national statutory regulations (e.g. in Germany: Technische Regeln Gasinstallation TRGI). Always comply with the currently valid regulations and installation instructions supplied by the gas appliance manufacturer. Only one side of the extractor hood may be installed next to a high-sided unit or high wall. Gap at least 50 mm. Minimum distance on gas hotplates between the upper edge of the trivet and lower edge of the extractor hood: 650 mm, Fig. 1.
Aluminium and plastic surfaces: q Do not use dry cloths. q Use a mild window cleaning agent. q Do not use aggressive, acidic or caustic
cleaners.
Observe the warranty regulations in the enclosed service booklet.

Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as hobs and ovens. Unrestricted operation is possible if the extractor hood is used in recirculating mode – with activated carbon filter. If the exhaust air is going to be discharged into the open, a telescopic wall box should be fitted into the outside wall.

120 150 120 150
For optimum extractor hood efficiency: q Short, smooth air exhaust pipe. q As few bends in the pipe as possible. q Diameter of pipe to be as large as
possible and no tight bends in pipe. If long, rough exhaust-air pipes, many pipe bends or smaller pipe diameters are used, the air extraction rate will no longer be at an optimum level and there will be an increase in noise.
Connecting a l 120 mm exhaust-air pipe: q Attach the reducing connector directly to
The manufacturer of the extractor hoods accepts no liability for complaints which can be attributed to the design and layout of the pipework. q Round pipes:
The exhaust air is discharged upwards through a ventilation shaft or directly through the outside wall into the open. D Exhaust air should neither be directed into a smoke or exhaust flue that is currently used for other purposes, nor into a shaft that is used for ventilating rooms in which stoves or fireplaces are also located. Exhaust air may be discharged in accordance with official and statutory regulations only (e.g. national building regulations). Local authority regulations must be observed when discharging air into smoke or exhaust flues that are not otherwise in use. D When the extractor hood is operated in exhaust-air mode simultaneously with a different burner which also makes use of the same chimney (such as gas, oil or coal-fired heaters, continuous-flow heaters, hot-water boilers) care must be taken to ensure that there is an adequate supply of fresh air which will be needed by the burner for combustion. Safe operation is possible provided that the underpressure in the room where the burner is installed does not exceed 4 Pa (0.04 mbar).
section that equates to that of round pipes. There should be no sharp bends. l 120 mm approx. 113 cm2 l 150 mm approx. 177 cm2
q If pipes have different diameters:
Insert sealing strip. q For exhaust-air mode, ensure that
Preparing the wall q The wall must be flat and perpendicular. q Ensure that the wall is capable of
there is an adequate supply of fresh air.
Circulating-air mode q With activated carbon filter if exhaust-air
providing a firm hold for mounting screws and plugs.
mode is not possible.
The complete installation set can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these opera- ting instructions.
Weight in kg:
Exhaust air Recirculating air
19,2 18,7 60 cm
This can be achieved if combustion air can flow through non-lockable openings, e.g. in doors, windows and via the air- intake/exhaust-air wall box or by other technical measures, such as reciprocal interlocking, etc. If the air intake is inadequate, there is a risk of poisoning from combustion gases which are drawn back into the room. An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will not be exceeded.
19,8 19,3 70 cm
20,9 20,4 90 cm
We reserve the right to construction changes within the context of technical development.
Exhaust-air mode

Installation
This extractor hood is intended to be mounted onto the kitchen wall. 1. Remove the grease filter (refer to Operating Instructions). 2. Draw a line on the wall from the ceiling to the lower edge of the hood at the centre of the location where the hood is going to be mounted. 3. Use the template to mark the points on the wall where the screws will be mounted. In order to make it easier to hook the hood onto the screws, draw the outline of the area where the hood will be attached. Ensure that the minimum distance bet- ween the hob and the extractor hood is maintained – 550 mm for an electric hob and 650 mm for a gas hob. The bottom edge of the template equates to the lower edge of the extractor hood. 4. Drill 4 x l 8 mm holes for the extractor hood and 2 x l 8 mm holes for the chimney panelling. Insert plugs into the holes so that they are flush with the wall.
Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. This is what you have to do: 1.Connect the green and yellow (Earth) wire to the terminal in the plug marked ‘E’ or with the symbol ( ), or coloured green or green and yellow. 2.Connect the blue (Neutral) wire to the terminal in the plug marked ‘N’ or coloured black. 3.Connect the brown (Live) wire to the terminal marked ‘L’, or coloured red.
The extractor hood should only be connected to an earthed socket that has been installed according to relevant regulations. If possible, site the earthed socket directly behind the chimney panelling. q The earthed socket should be
08. Screw in lower screws (hex screws). 09. Stick protective film over the holes of the 2 lower mounting bolts in the protective grid.
connected via its own circuit. q If the earthed socket is no longer
accessible following installation of the extractor hood, ensure that there is a permanently installed disconnector.
If it is necessary to wire the extractor hood directly into the mains: The extractor hood should only be connected to the electricity supply by a properly qualified electrician. A separator must be installed in the household circuit. A suitable separator is a switch that has a contact gap of more than 3 mm and interrupts all poles. Such devices include circuit breakers and contactors. If the connecting cable for this appliance is damaged, the cable must be replaced by the manufacturer or his customer service or a similarly qualified person in order to prevent serious injury to the user.
Electrical data: Are to be found on the name plate inside the appliance after removal of the filter frame. Before undertaking any repairs, always disconnect the extractor hood from the electricity supply. Length of the connecting cable: 1.30 m. This extractor hood corresponds to EC regulations concerning RF interference suppression.



Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.