FR
Constructa logo
Notice d'utilisation officielle

Constructa CD30636

56 pages·3.9 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD30636
Table des matières 183 sections Table of contents[en] Instructions for installation and use · Instruction manual · : Intended use · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their sa...p.1Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationp.2Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Clean the grease filter at least every 2 months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.3The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.3Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3Causes of damagep.3Caution!p.3Environmental protectionp.3Saving energyp.3■ Clean and, if required, replace the filter at regular intervals in order to increase the effectiveness of the ventilation system and to prevent the risk of fire.p.3Environmentally-friendly disposalp.3Operating modesp.4Exhaust air modep.4Notep.4■ If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.p.4Air recirculationp.4Notep.4Operating the appliancep.4Notep.4Control panel model 1 and 2p.4Setting the fanp.4Notep.4Control panel model 3p.4Setting the fanp.4Intensive settingp.5Fan run-on timep.5Lightingp.5Cleaning and maintenancep.5: Risk of burns!p.5: Risk of electric shock!p.5: Risk of electric shock!p.5: Risk of injury!p.5Cleaning agentsp.5■ High-pressure cleaners or steam cleaners.p.5Cleaning the metal mesh grease filtersp.5: Risk of fire!p.5Notesp.5By hand:p.5Notep.5■ Leave the metal mesh grease filters to drain.p.5In the dishwasher:p.5Notep.5■ Place the metal mesh grease filters loosely in the dishwasher. The metal mesh grease filters must not be wedged in.p.5Removing metal grease filterp.61. Open the lock and fold down the metal grease filter. While doing this, place your other hand under the metal grease filter.p.62. Take the metal grease filter out of the holder.p.6Notesp.63. Clean the metal grease filter.p.6■ To remove it, carefully lift the glass plate.p.6Installing the metal mesh grease filterp.61. Insert the metal mesh grease filter.p.62. Fold the metal mesh grease filter upwards, locking it in place.p.6Trouble shootingp.6: Risk of electric shock!p.6Malfunction tablep.6Replacing bulbsp.6: Risk of burns!p.6: Risk of electric shock!p.6Replacing halogen bulbsp.6Notep.61. Carefully remove the bulb ring using a suitable tool.p.72. Pull out the bulb and replace it with a bulb of the same type.p.73. Insert the bulb cover.p.74. Insert the mains plug or switch on the fuse again.p.7LED lightsp.7: Risk of injury!p.7After-sales servicep.7Accessoriesp.7Notep.7Notep.7Installation instructionsp.8■ The surfaces of the appliance are sensitive. Avoid damaging them during installation.p.8: Important safety informationp.9Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.9The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.9The width of the extractor hood must correspond at least with the width of the hob.p.9For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.9When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.9Risk of death!p.9Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.9Danger of death!p.9Risk of poisoning from flue gases that are drawn back in.p.9Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.9Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.9In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.9■ Adequate incoming air must therefore always be ensured.p.9■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.9Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.9In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.9Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.9Danger of death!p.9Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.9Risk of fire!p.10Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, t...p.10Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.p.10Risk of injury!p.10■ Components inside the appliance may have sharp edges. Wear protective gloves.p.10■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.10■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.10Risk of electric shock!p.10Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.10Risk of electric shock!p.10It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug is no longer accessible once the appliance has been...p.10Danger of suffocation!p.10Packaging material is dangerous to children. Never allow children to play with packaging material.p.10General informationp.10Exhaust air modep.10: Risk of death!p.10Exhaust ductp.10Notep.10■ The pipes or hoses for laying the exhaust air line must consist of non-combustible material.p.10■ Use sealing strips for different pipe diameters.p.10Electrical connectionp.10: Risk of electric shock!p.10: Risk of electric shock!p.11Preparing the unitsp.11■ The max. weight of the extractor hood is 18 kg.p.11Appliance dimensions and safety clearancesp.111. Make the cut-out for the exhaust air pipe. To do this, make an opening in the ceiling or back wall of the fitted unit with an additional recess for the power cord.p.112. If the cabinet base is present, remove this. Mark the securing points on the inside of the cabinet and pre-cut the holes using a piercer. Use the enclosed template to mark the securing points. ¨p.113. Screw in the four enclosed screws for the angle bracket up to 5 mm. ©p.11Preparing the appliancep.111. Use the screws provided to secure the handle strip to the filter pull-out.p.112. Connect the power cord provided to the appliance. ¨p.123. Use the strain relief to secure the power cord in place.©p.124. Screw the two angle brackets to the appliance. Ensure that the screws are positioned correctly.ª Screw in the screws until 8 mm of the threaded section is still protruding. «p.12Installationp.12Installationp.121. Use the angle brackets to hang the appliance on the screws and align it.p.122. Measure the distance from the appliance to the wall and mark this on the filler strip.p.123. If required, shorten the filler strip to the required dimension.p.124. Remove the appliance and screw in the filler strip.p.125. Remount the appliance, align it and screw it in place. Carefully screw in all screws.p.126. Establish the electrical connection.p.12Notep.12Change the filter pull-out's limit stopp.131. Pull the filter pull-out forwards.p.132. Shorten the spacer to the required dimension and insert it into the specified slot.p.13Connecting the pipesp.13Notep.13Exhaust-air pipe Ø 120 mmp.131. Attach the reducing connector directly to the air-pipe connector.p.132. Attach the exhaust air pipe to the reducing connector.p.133. Seal both joints appropriately.p.13
Page 1 of the Constructa CD30636 user manual — Table des matières
Page 1 · Table des matières
Table des matières

Table des matières

Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their sa...p.1Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationp.2Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Clean the grease filter at least every 2 months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.3The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.3Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3Causes of damagep.3Caution!p.3Environmental protectionp.3Saving energyp.3■ Clean and, if required, replace the filter at regular intervals in order to increase the effectiveness of the ventilation system and to prevent the risk of fire.p.3Environmentally-friendly disposalp.3Operating modesp.4Exhaust air modep.4Notep.4■ If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.p.4Air recirculationp.4Notep.4Operating the appliancep.4Notep.4Control panel model 1 and 2p.4Setting the fanp.4Notep.4Control panel model 3p.4Setting the fanp.4Intensive settingp.5Fan run-on timep.5Lightingp.5Cleaning and maintenancep.5: Risk of burns!p.5: Risk of electric shock!p.5: Risk of electric shock!p.5: Risk of injury!p.5Cleaning agentsp.5■ High-pressure cleaners or steam cleaners.p.5Cleaning the metal mesh grease filtersp.5: Risk of fire!p.5Notesp.5By hand:p.5Notep.5■ Leave the metal mesh grease filters to drain.p.5In the dishwasher:p.5Notep.5■ Place the metal mesh grease filters loosely in the dishwasher. The metal mesh grease filters must not be wedged in.p.5Removing metal grease filterp.61. Open the lock and fold down the metal grease filter. While doing this, place your other hand under the metal grease filter.p.62. Take the metal grease filter out of the holder.p.6Notesp.63. Clean the metal grease filter.p.6■ To remove it, carefully lift the glass plate.p.6Installing the metal mesh grease filterp.61. Insert the metal mesh grease filter.p.62. Fold the metal mesh grease filter upwards, locking it in place.p.6Trouble shootingp.6: Risk of electric shock!p.6Malfunction tablep.6Replacing bulbsp.6: Risk of burns!p.6: Risk of electric shock!p.6Replacing halogen bulbsp.6Notep.61. Carefully remove the bulb ring using a suitable tool.p.72. Pull out the bulb and replace it with a bulb of the same type.p.73. Insert the bulb cover.p.74. Insert the mains plug or switch on the fuse again.p.7LED lightsp.7: Risk of injury!p.7After-sales servicep.7Accessoriesp.7Notep.7Notep.7Installation instructionsp.8■ The surfaces of the appliance are sensitive. Avoid damaging them during installation.p.8: Important safety informationp.9Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.9The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.9The width of the extractor hood must correspond at least with the width of the hob.p.9For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.9When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.9Risk of death!p.9Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.9Danger of death!p.9Risk of poisoning from flue gases that are drawn back in.p.9Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.9Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.9In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.9■ Adequate incoming air must therefore always be ensured.p.9■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.9Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.9In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.9Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.9Danger of death!p.9Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.9Risk of fire!p.10Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, t...p.10Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.p.10Risk of injury!p.10■ Components inside the appliance may have sharp edges. Wear protective gloves.p.10■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.10■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.10Risk of electric shock!p.10Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.10Risk of electric shock!p.10It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug is no longer accessible once the appliance has been...p.10Danger of suffocation!p.10Packaging material is dangerous to children. Never allow children to play with packaging material.p.10General informationp.10Exhaust air modep.10: Risk of death!p.10Exhaust ductp.10Notep.10■ The pipes or hoses for laying the exhaust air line must consist of non-combustible material.p.10■ Use sealing strips for different pipe diameters.p.10Electrical connectionp.10: Risk of electric shock!p.10: Risk of electric shock!p.11Preparing the unitsp.11■ The max. weight of the extractor hood is 18 kg.p.11Appliance dimensions and safety clearancesp.111. Make the cut-out for the exhaust air pipe. To do this, make an opening in the ceiling or back wall of the fitted unit with an additional recess for the power cord.p.112. If the cabinet base is present, remove this. Mark the securing points on the inside of the cabinet and pre-cut the holes using a piercer. Use the enclosed template to mark the securing points. ¨p.113. Screw in the four enclosed screws for the angle bracket up to 5 mm. ©p.11Preparing the appliancep.111. Use the screws provided to secure the handle strip to the filter pull-out.p.112. Connect the power cord provided to the appliance. ¨p.123. Use the strain relief to secure the power cord in place.©p.124. Screw the two angle brackets to the appliance. Ensure that the screws are positioned correctly.ª Screw in the screws until 8 mm of the threaded section is still protruding. «p.12Installationp.12Installationp.121. Use the angle brackets to hang the appliance on the screws and align it.p.122. Measure the distance from the appliance to the wall and mark this on the filler strip.p.123. If required, shorten the filler strip to the required dimension.p.124. Remove the appliance and screw in the filler strip.p.125. Remount the appliance, align it and screw it in place. Carefully screw in all screws.p.126. Establish the electrical connection.p.12Notep.12Change the filter pull-out's limit stopp.131. Pull the filter pull-out forwards.p.132. Shorten the spacer to the required dimension and insert it into the specified slot.p.13Connecting the pipesp.13Notep.13Exhaust-air pipe Ø 120 mmp.131. Attach the reducing connector directly to the air-pipe connector.p.132. Attach the exhaust air pipe to the reducing connector.p.133. Seal both joints appropriately.p.13
Page 2 of the Constructa CD30636 user manual — Risk of fire! ■ Operating several gas burners at the
Page 2 · cliquer pour agrandir
Page 2

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Grease deposits in the grease filter may

catch fire. Clean the grease filter at least every 2 months.

Never operate the appliance without the grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of fire! ■ Operating several gas burners at the

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

Page 3 of the Constructa CD30636 user manual — Environmentally-friendly disposal
Page 3 · cliquer pour agrandir
Page 3

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

  • Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■ Items placed on the appliance may fall

Risk of electric shock! ■ Do not use any high-pressure cleaners or

down. Do not place any objects on the appliance.

steam cleaners, which can result in an electric shock.

Risk of injury! ■ The light emitted by LED lights is very

Causes of damage

dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

  • A defective appliance may cause electric

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Environmental protection

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

so that the extractor hood can work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the intensity of the cooking fumes.

Only use intensive mode where this is required. A lower fan speed means that less energy is consumed.

  • If there are intensive cooking fumes, select a higher fan

speed in good time. If cooking fumes have already spread in the kitchen, the extractor hood must be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and, if required, replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Page 4 of the Constructa CD30636 user manual — Setting the fan
Page 4 · cliquer pour agrandir
Page 4

Operating modes

This appliance can be used in exhaust-air mode or circulating- air mode.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

Exhaust air mode

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. The air which is drawn in is cleaned by the grease filters and an activated carbon filter, and is conveyed back into the kitchen.

Air recirculation

Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Control panel model 3

Constructa CD30636 — Control panel model 3 diagram (page 4)
Fig. 1 · Control panel model 3

Control panel model 1 and 2

Constructa CD30636 — Control panel model 1 and 2 diagram (page 4)
Fig. 2 · Control panel model 1 and 2

- Reduces the fan speed

+ Increases the fan speeds/intensive setting

Setting the fan

0, A Light on/off

Pull out the filter pull-out and press the # button. The fan starts at setting 2.

1 Fan speed 1

2 Fan speed 2

Press the + or - button to change the fan strength.

3 Fan speed 3

Press the # button. Slide the filter pull-out in.

Setting the fan

Pull out the filter pull-out. The fan starts at the selected level.

Press buttons 1, 2 or 3 in order to change the fan strength.

Slide the filter pull-out in as far as the limit stop.

Show 8 more labels / short text on this page
Explanation · < Light on/off · # Fan on/off · Explanation · Switching on · Switching off · Switching on · Switching off
Page 5 of the Constructa CD30636 user manual — Cleaning agents
Page 5 · cliquer pour agrandir
Page 5

Intensive setting

Fan run-on time

You can use the intensive setting if there is a large build-up of odours and fumes/vapours.

If you slide in the filter pull-out, the run-on time will be activated for as long as the extractor hood is operating.

Press the + button until all of the LEDs in the display light up. The intensive setting is activated.

After approx. 10 minutes, the fan switches off automatically.

Lighting

After approx. six minutes, the electronics automatically reduce the fan to a lower setting . If you want to end the intensive setting before the preset time expires, press the - button until the required fan setting is reached.

The lighting can be switched on and off independently of the ventilation.

Press the A button.

The run time is limited. The fan is then automatically reduced to a lower fan setting. You can switch back manually at any time.

Cleaning and maintenance

: Risk of burns!

The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning.

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Controls Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Risk of electric shock caused by pene- trating moisture.

Risk of damage to the electronics from penetrating moisture. Never clean operating controls with a wet cloth.

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Do not use any stainless steel cleaners.

: Risk of injury!

Cleaning the metal mesh grease filters

Components inside the appliance may have sharp edges. Wear protective gloves.

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Cleaning agents

To ensure that the different surfaces are not damaged by using the wrong cleaning agent, observe the information in the table. Do not use any of the following:

Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.

  • Harsh or abrasive cleaning agents,
  • Cleaning agents with a high alcohol content,
  • Hard scouring pads or cleaning sponges,
  • Do not use any aggressive, acidic or alkaline cleaning

agents.

  • High-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.

  • When cleaning the metal mesh grease filters, also clean the

holder for the metal mesh grease filters in the appliance using a damp cloth.

Follow all instructions and warnings included with the cleaning agents.

  • The metal mesh grease filters can be cleaned in the

dishwasher or by hand.

By hand:

Stainless steel Hot soapy water: Clean with a dish cloth and then dry with a soft cloth.

Clean stainless steel surfaces in the grind direction only.

  • Soak the metal mesh grease filters in a hot soapy solution.
  • Clean the filters with a brush and then rinse them thoroughly.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.

  • Leave the metal mesh grease filters to drain.

In the dishwasher:

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

  • Do not clean heavily soiled metal mesh grease filters together

Do not use any stainless steel cleaners.

with utensils.

Glass cleaner: Clean with a soft cloth.

  • Place the metal mesh grease filters loosely in the dishwasher.

The metal mesh grease filters must not be wedged in.

Area Cleaning agent · Area Cleaning agent · Aluminium and plas- tic

Page 6 of the Constructa CD30636 user manual — Malfunction table
Page 6 · cliquer pour agrandir
Page 6

Removing metal grease filter

  • Fat may accumulate in the bottom of the metal grease filter.
1. Open the lock and fold down the metal grease filter. While doing this, place your other hand under the metal grease filter.
  • Hold the metal grease filter level to prevent grease from

dripping out.

2. Take the metal grease filter out of the holder.
3. Clean the metal grease filter.

On appliances with a glass plate in the filter pull-out:

Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 3 · Removing metal grease filter
Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 4 · Removing metal grease filter
  • The glass plate can be removed easily and can be cleaned in

the dishwasher.

  • To remove it, carefully lift the glass plate.
Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 5 · Removing metal grease filter
Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 6 · Removing metal grease filter
Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 7 · Removing metal grease filter
Constructa CD30636 — Removing metal grease filter diagram (page 6)
Fig. 8 · Removing metal grease filter

Installing the metal mesh grease filter

1. Insert the metal mesh grease filter. While doing this, place the other hand under the metal mesh grease filter.
2. Fold the metal mesh grease filter upwards, locking it in place.

Trouble shooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

Replacing bulbs

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of burns!

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Halogen bulbs become very hot when switched on. There is still a risk of burning for some time after they have been switched off. Allow the halogen bulbs to cool down before replacing them.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

When changing the bulbs, the bulb socket contacts are live. Before changing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The bulbs are faulty.

For information on chang- ing the bulbs, see the "Replacing Bulbs" section.

· Replacing halogen bulbs

Page 7 of the Constructa CD30636 user manual — CZ5145X0
Page 7 · cliquer pour agrandir
Page 7
1. Carefully remove the bulb ring using a suitable tool. 2. Pull out the bulb and replace it with a bulb of the same type.

LED lights

Defective LED lights may be replaced by the manufacturer, their customer service or a qualified technician (electrician) only. : Risk of injury!

Constructa CD30636 — LED lights diagram (page 7)
Fig. 9 · LED lights

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.

Accessories

(not included in the scope of delivery)

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

Basic equipment:

Starter set for circulating-air mode

CZ5145X0

E no. FD no.

Throw-away filter for starter set

Handle strip60 cm:

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Handle strip90 cm :

Please find the contact data of all countries in the enclosed customer service list.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Show 6 more labels / short text on this page
Accessories Order number · 11008080 · After-sales serviceO · Stainless steel CZ5760X0 · Stainless steel CZ5790X0 · --------
Page 8 of the Constructa CD30636 user manual — [
Page 8 · cliquer pour agrandir
Page 8

INSTALLATION INSTRUCTIONS

Installation instructions These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Appliance width 60 cm:

Constructa CD30636 — INSTALLATION INSTRUCTIONS diagram (page 8)
Fig. 10
Constructa CD30636 — INSTALLATION INSTRUCTIONS diagram (page 8)
Fig. 11
  • This appliance is installed in a upper cabinet.
  • Follow the enclosed installation instructions for additional

special accessories (e.g. for circulating-air mode).

  • The surfaces of the appliance are sensitive. Avoid damaging

them during installation.

Constructa CD30636 — INSTALLATION INSTRUCTIONS diagram (page 8)
Fig. 12
Constructa CD30636 — INSTALLATION INSTRUCTIONS diagram (page 8)
Fig. 13

[

Constructa CD30636 — [ diagram (page 8)
Fig. 14

Appliance width, 90 cm:

Constructa CD30636 — [ diagram (page 8)
Fig. 15
Constructa CD30636 — [ diagram (page 8)
Fig. 16
Constructa CD30636 — [ diagram (page 8)
Fig. 17

[

Constructa CD30636 — [ diagram (page 8)
Fig. 18
Page 9 of the Constructa CD30636 user manual — : Important safety information
Page 9 · cliquer pour agrandir
Page 9

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.

open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the

Page 10 of the Constructa CD30636 user manual — ‘  ‘  ‘  ‘
Page 10 · cliquer pour agrandir
Page 10

Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.

Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

Risk of electric shock! It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug is no longer accessible once the appliance has been installed, or a fixed connection is required, the installation must have an all-pole isolating switch with a contact gap of at least 3 mm. Only an electrician may install the fixed connection. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■The appliance may fall down if it has not

been properly fastened in place. All fastening components must be fixed firmly and securely.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

General information

Exhaust air mode : Risk of death!

  • The appliance achieves its optimum performance by means

of a short, straight exhaust air pipe and as large a pipe diameter as possible.

Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

  • As a result of long, rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased.

  • The pipes or hoses for laying the exhaust air line must

consist of non-combustible material.

Round pipes An inner diameter of 150 mm, but at least 120 mm, is recommended.

If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.

Flat ducts The inner cross-section must correspond to the diameter of the round pipes.

Exhaust duct

150 mm diameter, approx. 177 cm2

120 mm diameter, approx. 113 cm2

  • Flat ducts should not have any sharp deflections.
  • Use sealing strips for different pipe diameters. Electrical connection : Risk of electric shock!

‘ ‘ ‘ ‘

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter.

Length of the cableapprox. 1.30 m

This appliance complies with the EC interference suppression regulations.

Page 11 of the Constructa CD30636 user manual — Preparing the appliance
Page 11 · cliquer pour agrandir
Page 11
2. If the cabinet base is present, remove this. Mark the securing points on the inside of the cabinet and pre-cut the holes using a piercer. Use the enclosed template to mark the securing points. ¨

It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug is no longer accessible once the appliance has been installed, or a fixed connection is required, the installation must have an all-pole isolating switch with a contact gap of at least 3 mm. Only an electrician may install the fixed connection. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

3. Screw in the four enclosed screws for the angle bracket up to 5 mm. ©
Constructa CD30636 — : Risk of electric shock! diagram (page 11)
Fig. 19 · : Risk of electric shock!
Constructa CD30636 — : Risk of electric shock! diagram (page 11)
Fig. 20 · : Risk of electric shock!

Preparing the units

  • The fitted unit must be level and have sufficient load-bearing

capacity.

  • The max. weight of the extractor hood is 18 kg.

Appliance dimensions and safety clearances

  • Observe the appliance's dimensions.
  • Comply with the safety clearances.

If the installation instructions for the gas cooking appliances specify a different distance, the largest distance must always be provided for.

The fitted unit must be heat-resistant up to 90 °C. The fitted unit must still be sturdy after the cut-outs have been made. To install an upper cabinet, this extractor hood must be provided with the following dimensions:

Constructa CD30636 — Preparing the units diagram (page 11)
Fig. 21 · Preparing the units

Depth Min. 320 mm

Height Min. 390 mm

Preparing the appliance

1. Make the cut-out for the exhaust air pipe. To do this, make an opening in the ceiling or back wall of the fitted unit with an additional recess for the power cord.

A handle strip must be screwed to the filter pull-out. This handle strip can be one that is provided with the appliance, or one that is available as an accessory.

Constructa CD30636 — Preparing the appliance diagram (page 11)
Fig. 22 · Preparing the appliance
1. Use the screws provided to secure the handle strip to the filter pull-out.

Width 600 mm

Page 12 of the Constructa CD30636 user manual — Installation
Page 12 · cliquer pour agrandir
Page 12
2. Connect the power cord provided to the appliance. ¨
4. Screw the two angle brackets to the appliance. Ensure that the screws are positioned correctly. ª Screw in the screws until 8 mm of the threaded section is still protruding. «
3. Use the strain relief to secure the power cord in place. ©
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 23 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 24 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 25 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 26 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 27 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 28 · 2. Connect the power cord provided to the appliance.…
Constructa CD30636 — 2. Connect the power cord provided to the appliance. ¨ diagram (page 12)
Fig. 29 · 2. Connect the power cord provided to the appliance.…

Installation

Installation

4. Remove the appliance and screw in the filler strip.
1. Use the angle brackets to hang the appliance on the screws and align it.
Constructa CD30636 — Installation diagram (page 12)
Fig. 30 · Installation
Constructa CD30636 — Installation diagram (page 12)
Fig. 31 · Installation
Constructa CD30636 — Installation diagram (page 12)
Fig. 32 · Installation
Constructa CD30636 — Installation diagram (page 12)
Fig. 33 · Installation
Constructa CD30636 — Installation diagram (page 12)
Fig. 34 · Installation
Constructa CD30636 — Installation diagram (page 12)
Fig. 35 · Installation
5. Remount the appliance, align it and screw it in place. Carefully screw in all screws.
6. Establish the electrical connection.
2. Measure the distance from the appliance to the wall and mark this on the filler strip.
3. If required, shorten the filler strip to the required dimension.
  • The intermediate floor must not be placed on the extractor

hood's housing.

  • The front panel must not be secured to the housing.
  • Access must be available in order to change the filter and for

after-sales service.

Page 13 of the Constructa CD30636 user manual — Connecting the pipes
Page 13 · cliquer pour agrandir
Page 13

Appliance width, 90 cm:

You must also screw the appliance onto the side upper cabinets.

Constructa CD30636 — Change the filter pull-out's limit stop diagram (page 13)
Fig. 36 · Change the filter pull-out's limit stop

Change the filter pull-out's limit stop

On some versions of the appliance, the limit stop for the filter pull-out can be changed. Spacers are included with these appliances in order to set the appliance's handle strip so that it is flush with the fitted unit.

1. Pull the filter pull-out forwards.
2. Shorten the spacer to the required dimension and insert it into the specified slot.
Constructa CD30636 — Change the filter pull-out's limit stop diagram (page 13)
Fig. 37 · Change the filter pull-out's limit stop
Constructa CD30636 — Change the filter pull-out's limit stop diagram (page 13)
Fig. 38 · Change the filter pull-out's limit stop
Constructa CD30636 — Change the filter pull-out's limit stop diagram (page 13)
Fig. 39 · Change the filter pull-out's limit stop

Connecting the pipes

Exhaust-air pipe Ø 150 mm (recommended size)

Attach the exhaust-air pipe directly to the air-pipe connector and seal.

Exhaust-air pipe Ø 120 mm

1. Attach the reducing connector directly to the air-pipe connector.
2. Attach the exhaust air pipe to the reducing connector.
3. Seal both joints appropriately.
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD30636

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD30636

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD30636 manuel PDF

56 pages·3.9 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…