FR
Constructa logo
Notice d'utilisation officielle

Constructa CD616650

52 pages·2.1 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD616650
Table des matières 175 sections Ú Table of contents[en] Instructions for installation and use · Instruction manual · : Intended useIntended use · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended useIntended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their sa...p.1Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationImportant safety informationp.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3Causes of damagep.3Caution!p.3Caution!p.3Environmental protectionp.3Saving energyp.3Environmentally-friendly disposalp.3Operating modesp.4Exhaust air modep.4Notep.4Circulating-air modep.4Notep.4Operating the applianceOperating the appliancep.4Notep.4Control panelp.4Setting the fanp.4Notep.4Lightingp.4Cleaning and maintenanceCleaning and maintenancep.4: Risk of burns!p.4: Risk of electric shock!p.4: Risk of electric shock!p.4: Risk of injury!p.4Caution!p.4Cleaning agentsp.5Notep.5Notep.5Removing metal grease filterp.51. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.p.52. Take the metal grease filter out of the holder.p.5Notesp.5Cleaning the metal mesh grease filtersp.5: Risk of fire!p.5Notesp.5By hand:p.5Notep.5In the dishwasher:p.5Notep.5Installing the metal mesh grease filterp.6: Risk of injury!p.6Notep.61. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.p.6Notep.62. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.p.6Trouble shootingTrouble shootingp.6: Risk of electric shock!p.6Malfunction tablep.6LED lightsp.6: Risk of injury!p.6Customer serviceCustomer servicep.6Accessoriesp.6Notep.6Notep.6Installation instructionsp.7: Important safety informationImportant safety informationp.7Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.7Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.7The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.7Caution!p.7Damage to the appliancep.7The surfaces of the appliance are sensitive. Avoid damaging them during installation.p.7The width of the extractor hood must correspond at least with the width of the hob.p.7For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.7Risk of fire!p.7Fatty deposits in the grease filter may catch fire. The specified safety clearances must be complied with in order to prevent a buildup of heat. Refer to the information provided for your cooker. If gas and electric hobs are being operated together...p.7Risk of fire!p.7Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat-producing appliance for solid fuel (e.g. wood or coal) unless a closed, non-removable...p.7When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.7Risk of death!p.8Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.8Danger of death!p.8Risk of poisoning from flue gases that are drawn back in.p.8Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.8Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.8In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.8■ Adequate incoming air must therefore always be ensured.p.8■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.8Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.8In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.8Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.8Danger of death!p.8Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.8Risk of injury!p.8■ Components inside the appliance may have sharp edges. Wear protective gloves.p.8■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.8■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.8■ Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.p.8Risk of electric shock!p.8■ Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.8■ It must always be possible to disconnect the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energ...p.8Risk of electric shock!p.9Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in ...p.9Danger of suffocation!p.9Packaging material is dangerous to children. Never allow children to play with packaging material.p.9General informationGeneral informationp.9Checking the wallp.9Electrical connectionp.9: Risk of electric shock!p.9: Risk of electric shock!p.9InstallationInstallationp.10Preparing the installationp.10Caution!p.101. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.p.102. Mark positions for the screws and the contour of the attachment area.p.103. Drill 8mm Ø holes to a depth of 80mm and press the wall plugs flush with the wall. ¨p.104. Screw on the fixing bracket for the flue duct. ©p.105. Screw in 2 securing screws with washers to approx.5mm. ªp.10Installationp.101. Attaching and aligning the appliance. ¨p.102. Mark the hole for the safety screw. ©p.103. Remove the appliance once more. ªp.10Finishing installation of the appliancep.101. Drill an 8mm Øhole to a depth of 80mm for the safety screw and press the wall plug flush into the wall. ¨p.102. First remove the protective foil from the back of the appliance and, following installation, remove the foil completely.p.103. Connect the appliance. ©p.104. Screw in the safety screw - and washer - and tighten all the screws. ªp.10Exhaust ductp.11Notep.11Connecting the appliance to the power supplyp.11Connecting the air extractorp.11Notep.111. Attach the air extractor pipe directly to the air-pipe connector.p.112. Connect to air extractor opening.p.113. Seal the joints appropriately.p.11Connect the power supplyp.111. Plug the mains plug into the earthed socket.p.112. If a fixed connection is required, please follow the instructions in the Electrical Connection section.p.11Attaching the flue ductp.11: Risk of injury!p.111. Separate the flue ducts.p.112. Remove the protective foil from both flue ducts.p.113. Screw the upper flue ducts to the sides of the fixing bracket using two short screws. ¨p.114. Place the lower flue ducts on the appliance and fix in place using two long screws on the bottom of the appliance. ©p.115. Screw the lower flue duct to the sides of the fixing bracket using 2 short screws. ªp.11Notep.11
Page 1 of the Constructa CD616650 user manual — : Intended use Intended use
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents [en]Instructions for installation and use

INSTRUCTION MANUAL 14

Trouble shooting 19 Customer service 19

Intended use 14 Important safety information 15 Environmental protection 16 Operating modes 17 Operating the appliance 17 Cleaning and maintenance 17

INSTALLATION INSTRUCTIONS 20

INSTRUCTION MANUAL

Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Intended use Intended use

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level.

This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their safety, or have been instructed in how to use the appliance safely and have understood the risks involved in not using it properly. Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Page 2 of the Constructa CD616650 user manual — Risk of fire! ■ Operating several gas burners at the
Page 2 · cliquer pour agrandir
Page 2

: Important safety information Important safety information

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Fatty deposits in the grease filter may

catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

  • Adequate incoming air must therefore

Risk of fire! ■ Operating several gas burners at the

always be ensured.

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

Page 3 of the Constructa CD616650 user manual — Saving energy
Page 3 · cliquer pour agrandir
Page 3

Risk of injury!

Causes of damage

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of injury! ■ The light emitted by LED lights is very

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Risk of electric shock!

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

  • A defective appliance may cause electric

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of damage as a result of incorrect loading of design elements. Do not pull design elements.Do not place objects on the design elements or hang objects from them.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

There is a risk of surface damage if you do not peel off the protective film.Remove the protective film from all parts of the appliance before using the appliance for the first time.

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of electric shock! ■ Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

Environmental protection

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

so that the extractor hood can work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the intensity of the cooking fumes.

Only use intensive mode where this is required. A lower fan speed means that less energy is consumed.

  • If there are intensive cooking fumes, select a higher fan

speed in good time. If cooking fumes have already spread in the kitchen, the extractor hood must be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and, if required, replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Page 4 of the Constructa CD616650 user manual — : Risk of electric shock!
Page 4 · cliquer pour agrandir
Page 4

Operating modes

This appliance can be used in exhaust-air mode or circulating- air mode.

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Exhaust air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

Note. To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Operating the appliance Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Setting the fan

Press button 1, 2 or 3.

Switch off all activated fan settings individually. To do this, press buttons 3, 2 and/or 1.

Lighting

The lighting can be switched on and off independently of the ventilation.

1 Fan setting on/off

Press the A button.

2 Fan setting on/off

3 Fan setting on/off

Cleaning and maintenance Cleaning and maintenance

: Risk of burns!

: Risk of injury!

The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

Components inside the appliance may have sharp edges. Wear protective gloves.

: Risk of electric shock!

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

There is a risk of surface damage if you do not peel off the protective film.Remove the protective film from all parts of the appliance before using the appliance for the first time.

: Risk of electric shock!

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Show 5 more labels / short text on this page
Switching on · Control panel · Switching off · Explanation · A Light on/off
Page 5 of the Constructa CD616650 user manual — Cleaning the metal mesh grease filters
Page 5 · cliquer pour agrandir
Page 5

Cleaning agents

Removing metal grease filter

To ensure that the different surfaces are not damaged by using the wrong cleaning product, follow the instructions in the table. Do not use any of the following:

1. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.
  • Harsh or abrasive cleaning agents, e.g. scouring powder or
2. Take the metal grease filter out of the holder.
Constructa CD616650 — Cleaning agents diagram (page 5)
Fig. 1 · Cleaning agents
  • Cleaning products with a high alcohol content,
  • Hard scouring pads or cleaning sponges,
  • Pressure washers or steam cleaners,
  • Cleaning products that dissolve limescale,
  • Aggressive all-purpose cleaning products,
  • Oven spray.

Stainless steel Hot soapy water: Clean with a dish cloth and then dry with a soft cloth.

Clean stainless steel surfaces in the direction of the grain only.

  • Fat may accumulate in the bottom of the metal grease filter.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers.Apply a very thin layer of the cleaning product with a soft cloth.

  • Hold the metal grease filter level to prevent fat from

dripping out.

Cleaning the metal mesh grease filters

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Painted surfaces Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

Do not use stainless steel cleaner.

Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

Hot soapy water: Clean with a soft cloth.

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

  • Do not use aggressive, acidic or alkaline cleaning products.

Controls Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

  • We recommend cleaning the grease filters every 2 months.
  • When cleaning the metal grease filters, also clean the metal

grease filter holder in the appliance using a damp cloth.

Risk of electric shock caused by pene- trating moisture.

  • The metal grease filters can be cleaned in the dishwasher or

by hand.

Risk of damage to the electronics caused by penetrating moisture. Never clean controls with a wet cloth.

By hand:

Do not use stainless steel cleaner.

  • Soak the metal grease filters in hot soapy water.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal grease filters to drain on an absorbent

material.

In the dishwasher:

  • Use normal domestic dishwashing detergents.
  • Do not clean heavily soiled metal grease filters together with

cookware.

  • Place the metal grease filters in the dishwasher, leaving

plenty of space around them. Do not trap the metal grease filters.

  • Select a temperature of no more than 50 °C.
Show 4 more labels / short text on this page
liquid scouring cleaner, · Area Cleaning products · Aluminium and plastic · --------
Page 6 of the Constructa CD616650 user manual — Accessories
Page 6 · cliquer pour agrandir
Page 6

Installing the metal mesh grease filter : Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

1. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.
2. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.

Trouble shooting Trouble shooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

LED lights

Defective LED lights may be replaced by the manufacturer, their customer service or a qualified technician (electrician) only. : Risk of injury!

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The LED lights are defective.

Call the after-sales ser- vice.

The button illu- mination does not work.

The control unit is faulty.

Call the aftersales ser- vice.

Customer service Customer service

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

Please find the contact data of all countries in the enclosed customer service list.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

Accessories

(not included in the scope of delivery)

E no. FD no.

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Starter set for air recirculation mode CZ5138X5

After-sales serviceO · Accessories Order number ·

Page 7 of the Constructa CD616650 user manual — : Important safety information Important safety information
Page 7 · cliquer pour agrandir
Page 7

INSTALLATION INSTRUCTIONS

Installation instructionsInstallation instructions

Constructa CD616650 — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 2
Constructa CD616650 — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 3
  • This appliance is installed on the wall.
  • Follow the enclosed installation instructions for additional

special accessories (e.g. for circulating-air mode).

  • The surfaces of the appliance are sensitive. Avoid damaging

them during installation.

: Important safety information Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.

Risk of fire! Fatty deposits in the grease filter may catch fire. The specified safety clearances must be complied with in order to prevent a build- up of heat. Refer to the information provi- ded for your cooker. If gas and electric hobs are being operated together, the lar- gest specified clearance applies.

Risk of fire! Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat-produ- cing appliance for solid fuel (e.g. wood or coal) unless a closed, non-removable cover is available. There must be no flying sparks. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.

Page 8 of the Constructa CD616650 user manual — Risk of electric shock! ■ It must always be possible to disconnect
Page 8 · cliquer pour agrandir
Page 8

Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■The appliance may fall down if it has not

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

been properly fastened in place. All fastening components must be fixed firmly and securely.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

Risk of injury! ■ Changes to the electrical or mechanical

assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.

Risk of electric shock!

  • Components inside the appliance may

have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

  • Adequate incoming air must therefore

always be ensured.

Risk of electric shock! ■ It must always be possible to disconnect

  • An incoming/exhaust air wall box alone

the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energy-isolating device in the phases must be provided in the permanent electrical installation in accordance with the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Page 9 of the Constructa CD616650 user manual — Electrical connection : Risk of electric shock!
Page 9 · cliquer pour agrandir
Page 9

Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after- sales service.

General information General information

Checking the wall

  • The wall must be level, vertical and adequately load-bearing.
  • The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

  • The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks).

  • The maximum weight of the extractor hood is 40 kg .

Electrical connection : Risk of electric shock!

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

The required connection information can be found on the rating plate on the top of the appliance.

Length of the cableapprox. 1.30 m

This appliance complies with the EC interference suppression regulations. : Risk of electric shock!

It must always be possible to disconnect the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energy- isolating device in the phases must be provided in the permanent electrical installation in accordance with the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

Page 10 of the Constructa CD616650 user manual — Finishing installation of the appliance
Page 10 · cliquer pour agrandir
Page 10

Installation Installation

Preparing the installation

Installation

1. Attaching and aligning the appliance. ¨

Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made.

2. Mark the hole for the safety screw. ©
3. Remove the appliance once more. ª
1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.
Constructa CD616650 — Preparing the installation diagram (page 10)
Fig. 4 · Preparing the installation
2. Mark positions for the screws and the contour of the attachment area.
3. Drill 8mm Ø holes to a depth of 80mm and press the wall plugs flush with the wall. ¨
4. Screw on the fixing bracket for the flue duct. ©
5. Screw in 2 securing screws with washers to approx.5mm. ª
Constructa CD616650 — Preparing the installation diagram (page 10)
Fig. 5 · Preparing the installation

Finishing installation of the appliance

1. Drill an 8mm Øhole to a depth of 80mm for the safety screw and press the wall plug flush into the wall. ¨
2. First remove the protective foil from the back of the appliance and, following installation, remove the foil completely.
3. Connect the appliance. ©
4. Screw in the safety screw - and washer - and tighten all the screws. ª
Constructa CD616650 — Finishing installation of the appliance diagram (page 10)
Fig. 6 · Finishing installation of the appliance
Page 11 of the Constructa CD616650 user manual — Connecting the appliance to the power supply
Page 11 · cliquer pour agrandir
Page 11

Exhaust duct

Attaching the flue duct : Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

  • The device achieves its optimum performance by means of a

short, straight exhaust air pipe and as large a pipe diameter as possible.

1. Separate the flue ducts. To do this, remove the adhesive tape
  • As a result of long rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased.

2. Remove the protective foil from both flue ducts.
3. Screw the upper flue ducts to the sides of the fixing bracket using two short screws. ¨
  • The pipes or hoses for laying the exhaust air line must
4. Place the lower flue ducts on the appliance and fix in place using two long screws on the bottom of the appliance. ©

consist of non-combustible material.

Round pipes An inner diameter of 150 mm, but at least 120 mm, is recommended.

5. Screw the lower flue duct to the sides of the fixing bracket using 2 short screws. ª

Flat ducts The inner cross-section must correspond to the diameter of the round pipes.

Constructa CD616650 — Exhaust duct diagram (page 11)
Fig. 7 · Exhaust duct

dia. 150 mm ca. 177 cm2

dia. 120 mm ca. 113 cm2

  • Flat ducts should not have any sharp deflections.
  • Use sealing strips for deviating pipe diameters.

Connecting the appliance to the power supply

Connecting the air extractor

1. Attach the air extractor pipe directly to the air-pipe connector.
2. Connect to air extractor opening.
3. Seal the joints appropriately.

Connect the power supply

1. Plug the mains plug into the earthed socket.
2. If a fixed connection is required, please follow the instructions in the Electrical Connection section.
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD616650

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD616650

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD616650 manuel PDF

52 pages·2.1 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…