FR
Constructa logo
Notice d'utilisation officielle

Constructa CD75132

60 pages·3.4 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD75132
Table des matières 174 sections Ú Table of contents[en] Instructions for installation and use · Instruction manual · : Intended useIntended use · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended useIntended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...p.1Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 15 years old and are being supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationImportant safety informationp.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Clean the grease filter at least every 2 months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.3The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.3Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3Causes of damagep.3Caution!p.3Environmental protectionEnvironmental protectionp.3Saving energyp.3Environmentally-friendly disposalp.3Operating modesOperating modesp.4Exhaust air modep.4Notep.4Air recirculationp.4Notep.4Operating the applianceOperating the appliancep.4Notep.4Control panelp.4Setting the fanp.4Intensive settingp.4Lightingp.4Cleaning and maintenanceCleaning and maintenancep.5: Risk of burns!p.5: Risk of electric shock!p.5: Risk of electric shock!p.5: Risk of injury!p.5Cleaning agentsp.5Removing metal grease filterp.51. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.p.52. Take the metal grease filter out of the holder.p.5Notesp.5Cleaning the metal mesh grease filtersp.5: Risk of fire!p.5Notesp.5By hand:p.6Notep.6In the dishwasher:p.6Notep.6Installing the metal mesh grease filterp.6: Risk of injury!p.6Notep.6Notep.6Activated charcoal filtersp.6Notesp.6Fitting the activated charcoal filterp.61. Remove the metal grease filter.p.62. Insert the screw through the wing nut and the sleeve. Screw it into the centre of the intermediate floor.p.6Notep.63. If the appliance has a spacer rail, remove this. Use a screwdriver to push the two tabs on the intermediate floor inwards.p.64. Mask the activated charcoal filter using the enclosed sealing strips.p.65. Insert the activated charcoal filter at the rear, fold it up and lock it in the centre using the wing nut. If the appliance has a spacer rail, reinsert this.p.76. Reinsert the metal grease filter.p.7Removing the activated charcoal filterp.71. Remove the metal grease filter.p.72. If the appliance has a spacer rail, remove this. Unlock the activated charcoal filter with the wing nut in the centre and remove it.p.73. Replace the activated carbon filter and lock it in place using the wing nut.p.74. If the appliance has a spacer rail, reinsert this. Reinsert the metal grease filter.p.7Trouble shootingTrouble shootingp.7: Risk of electric shock!p.7Malfunction tablep.7LED lightsp.7: Risk of injury!p.7After-sales servicep.8Accessoriesp.8Notep.8Notep.8Installation instructionsp.9: Important safety informationImportant safety informationp.10Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.10The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.10The width of the extractor hood must correspond at least with the width of the hob.p.10For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.10When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.10Risk of death!p.10Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.10Danger of death!p.10Risk of poisoning from flue gases that are drawn back in.p.10Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.10Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.10In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.10■ Adequate incoming air must therefore always be ensured.p.10■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.10Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.10In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.10Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.10Danger of death!p.10Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.10Risk of fire!p.11Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, t...p.11Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.p.11Risk of injury!p.11■ Components inside the appliance may have sharp edges. Wear protective gloves.p.11■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.11■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.11Risk of electric shock!p.11Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.11Risk of electric shock!p.11It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed.p.11The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of ...p.11The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.p.11Danger of suffocation!p.11Packaging material is dangerous to children. Never allow children to play with packaging material.p.11General informationGeneral informationp.12Exhaust air modep.12: Risk of death!p.12Exhaust ductp.12Notep.12Electrical connectionp.12: Risk of electric shock!p.12: Risk of electric shock!p.12Preparing the housingp.12Appliance dimensions and safety clearancesp.12Notep.12Preparing the appliancep.13Notep.131. Click the two spigots on the one-way flap into place in the holes on the air outlet and/or on the air inlet.p.132. Check that the one-way flap is working correctly.p.13InstallationInstallationp.14Final fitting stagep.141. Remove the metal grease filter.p.142. Establish the electrical connection.p.143. Push the extractor hood in the housing up until the mounting spring at the front and rear clicks into place.p.144. Screw the extractor hood in tightly.p.145. Insert and lock the metal grease filter.p.14Connecting the pipesp.14Notep.14Exhaust air pipe, dia. 120 mmp.141. Fit the reducing connector directly to the air-pipe connector.p.142. Attach the exhaust air pipe to the reducing connector.p.143. Seal both joints appropriately.p.14Removing the appliancep.141. Disconnect the electrical connection.p.142. Undo the screws.p.143. Disconnect the pipes.p.144. Hold the extractor hood down. Pull at the front and rear of the mounting spring.p.145. Pull the extractor hood downwards and out.p.14
Page 1 of the Constructa CD75132 user manual — : Intended use I ntended use
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents[en]I nstructi ons for i nstal l ati on and use

INSTRUCTION MANUAL 16

Trouble shooting 22 After-sales service 23

Intended use 16 Important safety information 17 Environmental protection 18 Operating modes 19 Operating the appliance 19 Cleaning and maintenance 20

INSTALLATION INSTRUCTIONS 24

INSTRUCTION MANUAL

Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Intended use I ntended use

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards.

Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 15 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Page 2 of the Constructa CD75132 user manual — Risk of fire! ■ Operating several gas burners at the
Page 2 · cliquer pour agrandir
Page 2

: Important safety information I mportant safety i nformati on

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Grease deposits in the grease filter may

catch fire. Clean the grease filter at least every 2 months.

Never operate the appliance without the grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of fire! ■ Operating several gas burners at the

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

Page 3 of the Constructa CD75132 user manual — Saving energy
Page 3 · cliquer pour agrandir
Page 3

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

  • Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■ Items placed on the appliance may fall

Risk of electric shock! ■ Do not use any high-pressure cleaners or

down. Do not place any objects on the appliance.

steam cleaners, which can result in an electric shock.

Risk of injury! ■ The light emitted by LED lights is very

Causes of damage

dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Risk of electric shock!

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

  • A defective appliance may cause electric

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of electric shock!

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Environmental protection Envi ronmental protecti on

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

to enable the extractor hood to work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the amount of steam produced

during cooking. Only use intensive mode when required. The lower the fan speed, the less energy is consumed.

  • If cooking produces large amounts of steam, select a higher

fan speed in good time. If the cooking steam has already spread around the kitchen, the extractor hood will need to be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and (if required) replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

  • Put the lid on to reduce cooking steam and condensation.
Page 4 of the Constructa CD75132 user manual — Lighting
Page 4 · cliquer pour agrandir
Page 4

Operating modes Operati ng modes

Exhaust air mode

Air recirculation

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

The air which is drawn in is cleaned by the grease filters and an activated carbon filter, and is conveyed back into the kitchen.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Operating the appliance Operati ng the appl i ance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Setting the fan

Slide the switch to the required fan setting.

Slide the switch to the zero setting.

Intensive setting

Control panel

You can use the intensive setting if there is a large build-up of odours and fumes/vapours.

Constructa CD75132 — Intensive setting diagram (page 4)
Fig. 1 · Intensive setting

Slide the switch to ˜.

Intensive mode is now activated.

Lighting

The lighting can be switched on and off independently of the ventilation.

3

Press the A button.

Show 6 more labels / short text on this page
Switching on · Switching off · Explanation · < Light on/off · 1-3 Fan settings · P Intensive mode
Page 5 of the Constructa CD75132 user manual — Cleaning the metal mesh grease filters
Page 5 · cliquer pour agrandir
Page 5

Cleaning and maintenance Cl eani ng and mai ntenance

: Risk of burns!

Removing metal grease filter

The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning.

1. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.

: Risk of electric shock!

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

: Risk of electric shock!

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

Cleaning agents

To ensure that the different surfaces are not damaged by using the wrong cleaning agent, observe the information in the table. Do not use any of the following:

2. Take the metal grease filter out of the holder.
  • Harsh or abrasive cleaning agents,
  • Cleaning agents with a high alcohol content,
  • Hard scouring pads or cleaning sponges,
  • High-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.

Follow all instructions and warnings included with the cleaning agents.

Stainless steel Hot soapy water: Clean with a dish cloth and then dry with a soft cloth.

Clean stainless steel surfaces in the grind direction only.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.

  • Fat may accumulate in the bottom of the metal grease filter.
  • Hold the metal grease filter level to prevent fat from

dripping out.

Cleaning the metal mesh grease filters

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Do not use any stainless steel cleaners.

Glass cleaner: Clean with a soft cloth.

Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Controls Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

  • Do not use any aggressive, acidic or alkaline cleaning

agents.

  • When cleaning the metal mesh grease filters, also clean the

Risk of electric shock caused by pene- trating moisture.

holder for the metal mesh grease filters in the appliance using a damp cloth.

Risk of damage to the electronics from penetrating moisture. Never clean operating controls with a wet cloth.

  • The metal mesh grease filters can be cleaned in the

dishwasher or by hand.

Do not use any stainless steel cleaners.

Show 4 more labels / short text on this page
· · Area Cleaning agent · Aluminium and plas- tic
Page 6 of the Constructa CD75132 user manual — Activated charcoal filters
Page 6 · cliquer pour agrandir
Page 6

By hand:

Fitting the activated charcoal filter

1. Remove the metal grease filter.
2. Insert the screw through the wing nut and the sleeve. Screw it into the centre of the intermediate floor.
  • Soak the metal mesh grease filters in a hot soapy solution.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal mesh grease filters to drain.
3. If the appliance has a spacer rail, remove this. Use a screwdriver to push the two tabs on the intermediate floor inwards.

In the dishwasher:

  • Do not clean heavily soiled metal mesh grease filters together

with utensils.

  • Place the metal mesh grease filters loosely in the dishwasher.

The metal mesh grease filters must not be wedged in.

Installing the metal mesh grease filter : Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

Constructa CD75132 — Installing the metal mesh grease filter : Risk of injury! diagram (page 6)
Fig. 2 · Installing the metal mesh grease filter : Risk of in…

Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.

Constructa CD75132 — Installing the metal mesh grease filter : Risk of injury! diagram (page 6)
Fig. 3 · Installing the metal mesh grease filter : Risk of in…
4. Mask the activated charcoal filter using the enclosed sealing strips.

Activated charcoal filters

Activated charcoal filters bind odorous substances in air recirculation mode. With normal use (approx. 1–2 hours a day), the activated charcoal filter should be replaced twice a year.

  • The activated charcoal filter is not included with the

appliance. The activated charcoal filter is available from specialist retailers, from our after-sales service or from our online shop.

  • The activated charcoal filter cannot be cleaned or reactivated.
  • Activated charcoal filters do not contain any harmful

substances and can be disposed of with your normal household waste.

·

Page 7 of the Constructa CD75132 user manual — Malfunction table
Page 7 · cliquer pour agrandir
Page 7
5. Insert the activated charcoal filter at the rear, fold it up and lock it in the centre using the wing nut. If the appliance has a spacer rail, reinsert this.

Removing the activated charcoal filter

1. Remove the metal grease filter.
2. If the appliance has a spacer rail, remove this. Unlock the activated charcoal filter with the wing nut in the centre and remove it.
Constructa CD75132 — 5. Insert the activated charcoal filter at the rear, fold it up and lock it in the centre using the wing nut. If the appliance has a spacer rail, reinsert this. diagram (page 7)
Fig. 4 · 5. Insert the activated charcoal filter at the rear,…
3. Replace the activated carbon filter and lock it in place using the wing nut.
4. If the appliance has a spacer rail, reinsert this. Reinsert the metal grease filter.
6. Reinsert the metal grease filter.

Trouble shooting Troubl e shooti ng

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

LED lights

Defective LED lights may be replaced by the manufacturer, their customer service or a qualified technician (electrician) only. : Risk of injury!

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The LED lights are defective.

Call the after-sales service.

Page 8 of the Constructa CD75132 user manual — Accessories
Page 8 · cliquer pour agrandir
Page 8

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

E no. FD no.

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Please find the contact data of all countries in the enclosed customer service list.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Accessories

(not included in the scope of delivery)

Activated charcoal filter CZ 5155X0

Circulated air grille 095660

After-sales serviceO · Accessory Order number ·

Page 9 of the Constructa CD75132 user manual — INSTALLATION INSTRUCTIONS
Page 9 · cliquer pour agrandir
Page 9

INSTALLATION INSTRUCTIONS

Installation instructions These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Appliance width 53 cm:

Constructa CD75132 — INSTALLATION INSTRUCTIONS diagram (page 9)
Fig. 5
  • This appliance is installed in chimneys or chimney hoods.
  • The surfaces of the appliance are sensitive. Avoid damaging
  • If the extractor hood is used in exhaust air mode, a one-way
Page 10 of the Constructa CD75132 user manual — : Important safety information I mportant safety i nformati on
Page 10 · cliquer pour agrandir
Page 10

: Important safety information I mportant safety i nformati on

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Page 11 of the Constructa CD75132 user manual — Risk of injury! ■ The appliance is heavy. To move the
Page 11 · cliquer pour agrandir
Page 11

Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.

Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

Risk of electric shock! It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■The appliance may fall down if it has not

been properly fastened in place. All fastening components must be fixed firmly and securely.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

Page 12 of the Constructa CD75132 user manual — ‘  ‘  ‘  ‘
Page 12 · cliquer pour agrandir
Page 12

General information General i nformati on

Exhaust air mode : Risk of death!

Electrical connection : Risk of electric shock!

Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter.

Length of the connecting cableApprox. 1.20 m

If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.

This appliance complies with the EC interference suppression regulations. : Risk of electric shock!

Exhaust duct

It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual- current circuit breaker (RCCB) in the appliance's power supply circuit.

‘ ‘ ‘ ‘

Preparing the housing

  • The extractor hood must be installed on the lower edge so

that it is flush with the housing.

  • The housing must cover the entire cooking area.
  • The max. weight of the extractor hood is 15 kg.
  • The appliance achieves its optimum performance by means

of a short, straight exhaust air pipe and as large a pipe diameter as possible.

Appliance dimensions and safety clearances

  • Take the appliance's dimensions into account.
  • As a result of long, rough exhaust air pipes, many pipe bends
  • Comply with the safety clearances.

or pipe diameters that are smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased.

If the installation instructions for the gas cooking appliances specify a different distance, the largest distance must always be provided for.

  • The pipes or hoses for laying the exhaust air line must

The surround must still be sturdy after the cut-outs have been made.

consist of non-combustible material.

Round pipes An inner diameter of 150 mm, but at least 120 mm, is recommended.

To install the extractor hood in a surround, the extractor hood must be provided with the following dimensions:

Flat ducts The inner cross-section must correspond to the diameter of the round pipes.

Width 500-3 mm (appliance width of 53 cm)

Width 700-3 mm (appliance width of 73 cm)

150 mm diameter, approx. 177 cm2

120 mm diameter, approx. 113 cm2

Height min. 160 mm (appliance with two motors)

  • Flat ducts should not have any sharp deflections.

Wall thickness 16 mm

  • Use sealing strips for different pipe diameters.

Depth 352-3 mm

Page 13 of the Constructa CD75132 user manual — Preparing the appliance
Page 13 · cliquer pour agrandir
Page 13

Extractor hood 53 cm wide, with one or two motors:

Preparing the appliance

Constructa CD75132 — Preparing the appliance diagram (page 13)
Fig. 6 · Preparing the appliance

Exhaust-air mode If the extractor hood is used in exhaust-air mode, a one-way flap must be installed.

1. Click the two spigots on the one-way flap into place in the holes on the air outlet and/or on the air inlet.
2. Check that the one-way flap is working correctly.

Air recirculation mode If the extractor hood is used in circulating-air mode, the blow opening must be secured using a circulated air grille. The circulated air grille prevents mechanical and electrical hazards.

Rectangular air outlet If the dust extractor hood has a rectangular air outlet, the air inlet provided must be screwed in tightly via the air outlet.

Extractor hood 73 cm wide, with one or two motors:

Constructa CD75132 — Preparing the appliance diagram (page 13)
Fig. 7 · Preparing the appliance
Page 14 of the Constructa CD75132 user manual — Connecting the pipes
Page 14 · cliquer pour agrandir
Page 14

Installation I nstal l ati on

Final fitting stage

Removing the appliance

1. Remove the metal grease filter.
1. Disconnect the electrical connection.
2. Establish the electrical connection.
Constructa CD75132 — Final fitting stage diagram (page 14)
Fig. 8 · Final fitting stage
3. Push the extractor hood in the housing up until the mounting spring at the front and rear clicks into place.
4. Hold the extractor hood down. Pull at the front and rear of the mounting spring.
Constructa CD75132 — Final fitting stage diagram (page 14)
Fig. 9 · Final fitting stage
5. Pull the extractor hood downwards and out.
5. Insert and lock the metal grease filter.

Connecting the pipes

Exhaust air pipe, dia. 150 mm (recommended size)

Fit the exhaust air pipe directly to the air-pipe connector and seal the joint.

Exhaust air pipe, dia. 120 mm

1. Fit the reducing connector directly to the air-pipe connector.
2. Attach the exhaust air pipe to the reducing connector.
3. Seal both joints appropriately.
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD75132

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD75132

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD75132 manuel PDF

60 pages·3.4 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…