FR
Constructa logo
Notice d'utilisation officielle

Constructa CD688860

60 pages·2.7 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD688860
Table des matières 213 sections Ú Table of contents[en] Instructions for installation and use · Instruction manual · : Intended useIntended use · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended useIntended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their sa...p.1Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationImportant safety informationp.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of injury!p.3Risk of trapping body parts when opening and closing the glass front. Do not reach into the area behind the glass panel, and keep your fingers away from the hinges.p.3Hazard due to magnetism!p.3Permanent magnets are inserted in the appliance front. They may affect electronic implants, e.g. heart pacemakers or insulin pumps. Wearers of electronic implants must stay at least 10 cm away from the appliance front.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3Causes of damagep.3Caution!p.3Environmental protectionEnvironmental protectionp.3Saving energyp.3■ During cooking, ensure that there is a sufficient supply of air so that the extractor hood can work efficiently and with a low level of operating noise.p.3Environmentally-friendly disposalp.3Operating modesOperating modesp.4Exhaust air modep.4Notep.4The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heat-producing appliances.p.4■ Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.p.4Circulating-air modep.4Notep.4To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are ...p.4Operating the applianceOperating the appliancep.4Notep.4Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes.p.4Control panelp.4Setting the fanp.4Switching onp.4Selecting the fan settingp.4Switching offp.4Intensive settingp.4Switching onp.4Notep.4After approx. 6 minutes, the extractor hood automatically switches back to fan setting 3.p.4Switching offp.4Lightingp.4Cleaning and maintenanceCleaning and maintenancep.5: Risk of burns!p.5The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.p.5: Risk of electric shock!p.5Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.p.5: Risk of electric shock!p.5Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.5: Risk of injury!p.5Components inside the appliance may have sharp edges. Wear protective gloves.p.5: Risk of injury!p.5Risk of trapping body parts when opening and closing the glass front. Do not reach into the area behind the glass panel, and keep your fingers away from the hinges.p.5Cleaning agentsp.5■ Harsh or abrasive cleaning agents, e.g. scouring powder or liquid scouring cleaner,p.5Notep.5Wash new sponge cloths thoroughly before use.p.5Notep.5Follow all instructions and warnings included with the cleaning products.p.5Removing metal grease filterp.51. Open the glass front slowly and fully. Hold the glass front in the centre when doing so, gripping it firmly.p.52. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.p.53. Take the metal grease filter out of the holder.p.5Notesp.5Cleaning the metal mesh grease filtersp.6: Risk of fire!p.6Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.p.6Notesp.6By hand:p.6Notep.6You can use a special degreaser to remove stubborn dirt. This can be ordered from the online shop.p.6In the dishwasher:p.6Notep.6Slight discolouration may occur if the metal grease filters are cleaned in the dishwasher. This discolouration has no effect on the performance of the metal grease filters.p.6Installing the metal mesh grease filterp.6: Risk of injury!p.6Components inside the appliance may have sharp edges. Wear protective gloves.p.6Notep.6Clean all accessible parts of the housing.p.61. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.p.6Notep.62. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.p.6Trouble shootingTrouble shootingp.6: Risk of electric shock!p.6Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in ...p.6Malfunction tablep.6LED lightsp.6: Risk of injury!p.6The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.6Customer serviceCustomer servicep.7Accessoriesp.7Notep.7These instructions apply to several appliance models. It may be the case that an optional accessory that is listed does not apply for your appliance.p.7Notep.7Observe the installation instructions in the accessory.p.7Installation instructionsp.8Notep.8We recommend fitting the appliance such that the lower edge of the glass screen is in line with the lower edges of the adjacent wall-hung cabinets. Make sure that the specified safety clearances from the hob are complied with.p.8: Important safety informationImportant safety informationp.9Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.9Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.9The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.9The surfaces of the appliance are easily damaged. Avoid damaging them during installation.p.9The width of the extractor hood must correspond at least with the width of the hob.p.9For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.9Risk of fire!p.9■ Fatty deposits in the grease filter may catch fire. The specified safety clearances must be complied with in order to prevent a build-up of heat. Refer to the information provided for your cooker. If gas and electric hobs are being operated toget...p.9■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.9When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.9Risk of death!p.9Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.9Danger of death!p.9Risk of poisoning from flue gases that are drawn back in.p.9Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.9Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.9In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.9■ Adequate incoming air must therefore always be ensured.p.9■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.9Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.9In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.10Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.10Danger of death!p.10Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.10Risk of injury!p.10■ Components inside the appliance may have sharp edges. Wear protective gloves.p.10■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.10■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.10■ Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.p.10Hazard due to magnetism!p.10Permanent magnets are inserted in the appliance front. They may affect electronic implants, e.g. heart pacemakers or insulin pumps. Wearers of electronic implants must stay at least 10 cm away from the appliance front.p.10Risk of electric shock!p.10■ Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.10■ It must always be possible to disconnect the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energ...p.10Risk of electric shock!p.10Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in ...p.10Danger of suffocation!p.10Packaging material is dangerous to children. Never allow children to play with packaging material.p.10General informationGeneral informationp.11Checking the wallp.11Electrical connectionp.11: Risk of electric shock!p.11Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.11: Risk of electric shock!p.11It must always be possible to disconnect the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energyi...p.11InstallationInstallationp.12Preparing for installationp.12Caution!p.121. Determine where the extractor hood should be positioned and lightly mark where the lower edge of the appliance should be on the wall. Determine where the middle should be based on the hob.p.12Notep.122. Place the template against the line drawn on the wall and fasten it in place. Mark where the screws should be inserted.p.123. Drill 8 mm diameter holes to a depth of 80 mm for fastening the appliance, remove the template and press in the wall plugs flush with the wall.p.12Fitting with a flue ductp.13Fitting without a flue ductp.13Installationp.13Wall-mounting the appliance and levelling itp.141. First remove the protective film from the back of the appliance and, following installation, remove the rest of the film.p.142. When mounting the appliance, ensure that it engages properly with the mounting supports.p.143. If required, the appliance can be moved to the right or to the left.p.144. Firmly tighten the screws for the mounting supports. Hold the bracket firmly when doing so. ¨p.145. If no duct is to be fitted, screw in the two locking screws without the bracket. ©p.14Connecting the pipesp.14Notep.14If an aluminium pipe is being used, smooth the connection area beforehand.p.14Exhaust air pipe, dia. 120 mmp.141. Fit the reducing connector directly to the air-pipe connector.p.142. Attach the exhaust air pipe to the reducing connector.p.143. Use suitable means to seal both joints.p.14Attaching the flue ductp.14: Risk of injury!p.14From sharp edges during installation. Always wear protective gloves while installing the appliance.p.14: Risk of electric shock!p.14Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.141. Separate the flue duct sections by removing the adhesive tape.p.142. Remove the pieces of protective film from both flue duct sections.p.143. Push one flue duct section into the other.p.14Notesp.144. Place flue ducts sections on the appliance.p.145. Slide the inner flue duct section upwards, attach it to the left and right sides of the retaining bracket, and then slide it down to engage it. ¨p.146. Screw the flue duct section to the sides of the retaining bracket using two screws. ©p.147. Clip the lower flue duct section in at the retaining bracket. The connection cable must not be damaged. ªp.14Notep.14If an air-recirculation optional accessory has been fitted and the extractor hood is to be operated without a flue duct, the cable must be wound onto the connector.p.14
Page 1 of the Constructa CD688860 user manual — : Intended use I ntended use
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents[en]I nstructi ons for i nstal l ati on and use

INSTRUCTION MANUAL 16

Trouble shooting 21 Customer service 22

Intended use 16 Important safety information 17 Environmental protection 18 Operating modes 19 Operating the appliance 19 Cleaning and maintenance 20

INSTALLATION INSTRUCTIONS 23

INSTRUCTION MANUAL

Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Intended use I ntended use

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their safety, or have been instructed in how to use the appliance safely and have understood the risks involved in not using it properly. Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless

they are over 15 years of age and are supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Page 2 of the Constructa CD688860 user manual — Risk of fire! ■ Operating several gas burners at the
Page 2 · cliquer pour agrandir
Page 2

: Important safety information I mportant safety i nformati on

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Fatty deposits in the grease filter may

catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

  • Adequate incoming air must therefore

Risk of fire! ■ Operating several gas burners at the

always be ensured.

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

Page 3 of the Constructa CD688860 user manual — Saving energy
Page 3 · cliquer pour agrandir
Page 3

Risk of injury!

  • Components inside the appliance may
  • A defective appliance may cause electric

have sharp edges. Wear protective gloves.

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Risk of injury! ■ The light emitted by LED lights is very

dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of injury! Risk of trapping body parts when opening and closing the glass front. Do not reach into the area behind the glass panel, and keep your fingers away from the hinges.

Risk of electric shock! ■ Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

Hazard due to magnetism! Permanent magnets are inserted in the appliance front. They may affect electronic implants, e.g. heart pacemakers or insulin pumps. Wearers of electronic implants must stay at least 10 cm away from the appliance front.

Causes of damage

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Risk of damage as a result of incorrect loading of design elements. Do not pull design elements.Do not place objects on the design elements or hang objects from them.

Environmental protection Envi ronmental protecti on

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

  • Switch off the lighting if you no longer require it.
  • Clean and, if required, replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Saving energy

Environmentally-friendly disposal

  • During cooking, ensure that there is a sufficient supply of air

so that the extractor hood can work efficiently and with a low level of operating noise.

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

  • Adjust the fan speed to the intensity of the cooking fumes.

Only use intensive mode where this is required. A lower fan speed means that less energy is consumed.

  • If there are intensive cooking fumes, select a higher fan

speed in good time. If cooking fumes have already spread in the kitchen, the extractor hood must be operated for longer.

  • Switch off the extractor hood if you no longer require it.
Page 4 of the Constructa CD688860 user manual — Setting the fan
Page 4 · cliquer pour agrandir
Page 4

Operating modes Operati ng modes

Exhaust air mode

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Operating the appliance Operati ng the appl i ance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Intensive setting

You can use the intensive setting if there is a large build-up of odours and fumes/vapours.

Touch the P symbol.

Control panel

If you want to end intensive mode before the preset time expires, touch the P symbol.

Lighting

The lighting can be switched on and off independently of the fan.

Touch the 6 symbol.

Setting the fan

Touch the # symbol.

The fan starts at fan setting 2.

Selecting the fan setting

Touch symbol 1, 2 or 3 to set a different fan setting.

Touch the # symbol.

Show 9 more labels / short text on this page
Switching on · Switching off · Symbol Explanation · # Fan on/off · 1-3 Fan settings · P Intensive mode · 6 Light on/off · Switching on · Switching off
Page 5 of the Constructa CD688860 user manual — -------- Removing metal grease filter
Page 5 · cliquer pour agrandir
Page 5

Cleaning and maintenance Cl eani ng and mai ntenance

: Risk of burns!

The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

Stainless steel Hot soapy water: Clean with a dish cloth and then dry with a soft cloth.

Clean stainless steel surfaces in the direction of the grain only.

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers.Apply a very thin layer of the cleaning product with a soft cloth.

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

Do not use stainless steel cleaner.

Hot soapy water: Clean with a soft cloth.

: Risk of injury!

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Risk of trapping body parts when opening and closing the glass front. Do not reach into the area behind the glass panel, and keep your fingers away from the hinges.

Controls Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

Cleaning agents

To ensure that the different surfaces are not damaged by using the wrong cleaning product, follow the instructions in the table. Do not use any of the following:

Risk of electric shock caused by pene- trating moisture.

Risk of damage to the electronics caused by penetrating moisture. Never clean controls with a wet cloth.

  • Harsh or abrasive cleaning agents, e.g. scouring powder or
  • Cleaning products with a high alcohol content,

Do not use stainless steel cleaner.

  • Hard scouring pads or cleaning sponges,

Removing metal grease filter

  • Pressure washers or steam cleaners,
  • Cleaning products that dissolve limescale,
1. Open the glass front slowly and fully. Hold the glass front in the centre when doing so, gripping it firmly.
  • Aggressive all-purpose cleaning products,
2. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.
  • Oven spray.
3. Take the metal grease filter out of the holder.
Constructa CD688860 — -------- Removing metal grease filter diagram (page 5)
Fig. 1 · -------- Removing metal grease filter
  • Fat may accumulate in the bottom of the metal grease filter.
  • Hold the metal grease filter level to prevent grease from

dripping out.

Area Cleaning products · Aluminium and plastic · liquid scouring cleaner,

Page 6 of the Constructa CD688860 user manual — LED lights
Page 6 · cliquer pour agrandir
Page 6

Cleaning the metal mesh grease filters

Installing the metal mesh grease filter : Risk of injury!

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Components inside the appliance may have sharp edges. Wear protective gloves.

Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

1. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.
  • Do not use aggressive, acidic or alkaline cleaning products.
  • We recommend cleaning the grease filters every 2 months.
2. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.
  • When cleaning the metal grease filters, also clean the metal

grease filter holder in the appliance using a damp cloth.

  • The metal grease filters can be cleaned in the dishwasher or

by hand.

By hand:

  • Soak the metal grease filters in hot soapy water.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal grease filters to drain on an absorbent

material.

In the dishwasher:

  • Use normal domestic dishwashing detergents.
  • Do not clean heavily soiled metal grease filters together with

cookware.

  • Place the metal grease filters in the dishwasher, leaving

plenty of space around them. Do not trap the metal grease filters.

  • Select a temperature of no more than 50 °C.

Trouble shooting Troubl e shooti ng

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

LED lights

Defective LED lights may be replaced by the manufacturer, their customer service or a qualified technician (electrician) only. : Risk of injury!

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service. Malfunction table

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The LED lights are defective.

Call the after-sales ser- vice.

The button illu- mination does not work.

The control unit is faulty.

Call the aftersales ser- vice.

Page 7 of the Constructa CD688860 user manual — CZ5170X1
Page 7 · cliquer pour agrandir
Page 7

Customer service Customer servi ce

When calling us, please quote the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. These numbers can be found on the rating plate on the top of the appliance.

Accessories

(not included in the scope of delivery)

Z-NrFD: E-Nr:

Type:

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

Starter set for air recirculation mode (flat hood with chimney)

CZ51AFU0X0

Easy-change filter for starter set

CZ51AFA0X

E no. FD no.

Starter set for air recirculation mode (flat hood without chimney)

CZ51AFT0X0

Easy-change filter for starter set

CZ51AFA0X0

Starter set for air recirculation mode (angled canopy hood with chimney)

CZ51AIU0X0

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Easy-change filter for starter set

CZ51AIA0X0

Please find the contact data of all countries in the enclosed customer service list.

Starter set for air recirculation mode (angled canopy hood without chimney)

CZ51AIT0X0

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Easy-change filter for starter set

CZ51AIA0X0

Starter set for air recirculation mode with fil- ter that can be regenerated (flat hood with chimney)

CZ51AFS0X0

Starter set for air recirculation mode with fil- ter that can be regenerated (angled canopy hood with chimney)

CZ51AIS0X0

Starter set for air recirculation mode with fil- ter that can be regenerated (flat hood with- out chimney)

CZ51AFR0X0

Starter set for air recirculation mode with fil- ter that can be regenerated (angled canopy hood without chimney)

CZ51AIR0X0

CleanAir air recirculation module

CZ51AXC0N0

Easy-change filter for CleanAir air recircula- tion module (cannot be regenerated)

CZ5170X1

Easy-change filter for CleanAir air recircula- tion module (can be regenerated) CZ50XXP0X0

Accessories Order number · After-sales serviceO ·

Page 8 of the Constructa CD688860 user manual — A B
Page 8 · cliquer pour agrandir
Page 8

INSTALLATION INSTRUCTIONS

  • This appliance is installed on the wall.
  • If the extractor hood is to be operated in exhaust-air mode, a

PLQ PP PLQ PP PD[PP

flue duct must be fitted. If the extractor hood is to be operated in air-recirculation mode, an optional accessory must be fitted. To do this, refer to the installation instructions provided.The flue duct does not need to be fitted for air-recirculation mode.

PP

Constructa CD688860 — PP diagram (page 8)
Fig. 2
Constructa CD688860 — PP diagram (page 8)
Fig. 3
  • For additional optional accessories, refer to the installation

instructions provided.

  • The surfaces of the appliance are sensitive. Avoid damaging

PLQ PP

them during installation.

Constructa CD688860 — PLQ PP diagram (page 8)
Fig. 4
Constructa CD688860 — PLQ PP diagram (page 8)
Fig. 5

•PP

•PP

PLQ PP

PP

PLQ PP PD[PP

Constructa CD688860 — •PP diagram (page 8)
Fig. 6

PLQ PP

•PP

•PP

A B

Constructa CD688860 — A B diagram (page 8)
Fig. 7
Constructa CD688860 — A B diagram (page 8)
Fig. 8
Show 5 more labels / short text on this page
Installation instructions · $ · $ % · $ % · %
Page 9 of the Constructa CD688860 user manual — Risk of fire! ■ Grease deposits in the grease filter may
Page 9 · cliquer pour agrandir
Page 9

: Important safety information I mportant safety i nformati on

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. The surfaces of the appliance are easily damaged. Avoid damaging them during installation. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.

the consent of the heating engineer responsible.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire!

  • Fatty deposits in the grease filter may

catch fire. The specified safety clearances must be complied with in order to prevent a build-up of heat. Refer to the information provided for your cooker. If gas and electric hobs are being operated together, the largest specified clearance applies.

Risk of fire! ■ Grease deposits in the grease filter may

  • Adequate incoming air must therefore

always be ensured.

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain

Page 10 of the Constructa CD688860 user manual — Risk of injury! ■ Changes to the electrical or mechanical
Page 10 · cliquer pour agrandir
Page 10

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

  • Components inside the appliance may

have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

Risk of electric shock! ■ It must always be possible to disconnect

the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energy-isolating device in the phases must be provided in the permanent electrical installation in accordance with the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■The appliance may fall down if it has not

Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after- sales service.

been properly fastened in place. All fastening components must be fixed firmly and securely.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

Risk of injury! ■ Changes to the electrical or mechanical

assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.

Hazard due to magnetism! Permanent magnets are inserted in the appliance front. They may affect electronic implants, e.g. heart pacemakers or insulin pumps. Wearers of electronic implants must stay at least 10 cm away from the appliance front.

Page 11 of the Constructa CD688860 user manual — Electrical connection : Risk of electric shock!
Page 11 · cliquer pour agrandir
Page 11

General information General i nformati on

Checking the wall

  • The wall must be level, vertical and adequately load-bearing.
  • The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

  • The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks).

  • The maximum weight of the extractor hood is 40 kg .

Electrical connection : Risk of electric shock!

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

The required connection information can be found on the rating plate on the top of the appliance.

Length of the cableapprox. 1.30 m

This appliance complies with the EC interference suppression regulations. : Risk of electric shock!

It must always be possible to disconnect the appliance from the power supply. The appliance must only be connected to a protective contact socket that has been correctly installed. If the plug can no longer be reached after installation, an energy- isolating device in the phases must be provided in the permanent electrical installation in accordance with the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance's power supply circuit.

Page 12 of the Constructa CD688860 user manual — [ •PP
Page 12 · cliquer pour agrandir
Page 12

Installation I nstal l ati on

Preparing for installation

Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled.

If the extractor hood is to be operated in exhaust-air mode, a flue duct must be fitted.

Constructa CD688860 — Preparing for installation diagram (page 12)
Fig. 9 · Preparing for installation
Constructa CD688860 — Preparing for installation diagram (page 12)
Fig. 10 · Preparing for installation

If the extractor hood is to be operated in air-recirculation mode, an optional accessory must be fitted. To do this, refer to the installation instructions provided. The flue duct does not need to be fitted for air-recirculation mode.

1. Determine where the extractor hood should be positioned and lightly mark where the lower edge of the appliance should be on the wall. Determine where the middle should be based on the hob.

[ •PP

[ •PP

Constructa CD688860 — [ •PP diagram (page 12)
Fig. 11

[ •PP

[ •PP

2. Place the template against the line drawn on the wall and fasten it in place. Mark where the screws should be inserted. To fit the flue duct, the template must be cut along the marked cut line.
3. Drill 8 mm diameter holes to a depth of 80 mm for fastening the appliance, remove the template and press in the wall plugs flush with the wall.
Show 6 more labels / short text on this page
$ · \ · ] · % · \ · ]
Page 13 of the Constructa CD688860 user manual — Installation
Page 13 · cliquer pour agrandir
Page 13

Fitting with a flue duct Fitting without a flue duct

Constructa CD688860 — Fitting with a flue duct diagram (page 13)
Fig. 12 · Fitting with a flue duct
Constructa CD688860 — Fitting with a flue duct diagram (page 13)
Fig. 13 · Fitting with a flue duct

Installation

Constructa CD688860 — Installation diagram (page 13)
Fig. 14 · Installation

Screw in the mounting supports for the extractor hood until they are hand-tight, use a spirit level to level the appliance and then screw the mounting supports in fully.

Page 14 of the Constructa CD688860 user manual — Attaching the flue duct
Page 14 · cliquer pour agrandir
Page 14

Wall-mounting the appliance and levelling it

  • To prevent scratches, lay paper over the edges of the outer
1. First remove the protective film from the back of the appliance and, following installation, remove the rest of the film.

flue duct section to protect the surface.

  • The slots of the inner flue duct section point downwards.
2. When mounting the appliance, ensure that it engages properly with the mounting supports.
4. Place flue ducts sections on the appliance.
5. Slide the inner flue duct section upwards, attach it to the left and right sides of the retaining bracket, and then slide it down to engage it. ¨
3. If required, the appliance can be moved to the right or to the left.
4. Firmly tighten the screws for the mounting supports. Hold the bracket firmly when doing so. ¨
6. Screw the flue duct section to the sides of the retaining bracket using two screws. ©
Constructa CD688860 — Wall-mounting the appliance and levelling it diagram (page 14)
Fig. 15 · Wall-mounting the appliance and levelling it
Constructa CD688860 — Wall-mounting the appliance and levelling it diagram (page 14)
Fig. 16 · Wall-mounting the appliance and levelling it
5. If no duct is to be fitted, screw in the two locking screws without the bracket. ©

Connecting the pipes

If the extractor hood is to be operated in exhaust-air mode, the pipes must be connected. If the extractor hood is to be operated in air-recirculation mode, an optional accessory must be fitted. To do this, refer to the installation instructions provided.

Exhaust air pipe, dia. 150 mm (recommended size)

Fit the exhaust air pipe directly to the air-pipe connector and seal the joint.

Exhaust air pipe, dia. 120 mm

7. Clip the lower flue duct section in at the retaining bracket. The connection cable must not be damaged. ª
1. Fit the reducing connector directly to the air-pipe connector.
2. Attach the exhaust air pipe to the reducing connector.
3. Use suitable means to seal both joints.

Attaching the flue duct

If the extractor hood is to be operated in exhaust-air mode, a flue duct must be fitted.

The flue duct does not need to be fitted for air-recirculation mode. : Risk of injury!

From sharp edges during installation. Always wear protective gloves while installing the appliance.

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

1. Separate the flue duct sections by removing the adhesive tape.
2. Remove the pieces of protective film from both flue duct sections.
3. Push one flue duct section into the other.
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD688860

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD688860

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD688860 manuel PDF

60 pages·2.7 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…