FR
Constructa logo
Notice d'utilisation officielle

Constructa CD669862

32 pages·1.4 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD669862
Table des matières 141 sections Ú Table of contents[en] Instruction manual · Produktinfo · Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com · : Important safety information · … AfficherMasquer
Ú Table of contents[en] Instruction manualp.1Produktinfop.1Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.comp.1: Important safety informationp.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...p.1Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1Danger of suffocation!p.1Packaging material is dangerous to children. Never allow children to play with packaging material.p.1Danger of death!p.1Risk of poisoning from flue gases that are drawn back in.p.1Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.1Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.1In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Clean the grease filter at least every 2 months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2Risk of injury!p.2■ Components inside the appliance may have sharp edges. Wear protective gloves.p.2■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.2Risk of electric shock!p.2■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.2■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.2Causes of damagep.3Environmental protectionp.3Saving energyp.3Environmentally-friendly disposalp.3Dispose of packaging in an environmentally-friendly manner.p.3Operating modesp.3Exhaust air modep.3Notep.3Circulating-air modep.3Notep.3Operating the appliancep.4These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.p.4Notep.4Control panelp.4Setting the fanp.4Notep.4Switching onp.4Press button 1, 2 or 3.p.4To confirm the setting, the 0 button and the set fan speed light up.p.4Switching off the appliancep.4Press the 0 button.p.4Fan run-on timep.4The fan run-on is possible in any fan speed.p.41. First, press the button for the required fan speed 1, 2 or 3 .p.42. To activate the fan run-on, press and hold the % button for 2 seconds.p.43. To end the fan run-on early, press the 0 button.p.4Notesp.4Intensive settingp.4You can use the intensive setting if there is a large build-up of odours and fumes/vapours.p.41. To activate the intensive setting, press and hold the g button for 2 seconds.p.42. To end the intensive setting early, press the 0 button.p.4Notep.4Lightingp.4The lighting can be switched on and off independently of the ventilation.p.4Setting the brightnessp.4When switching on the lights, press and hold the @ button for 2 seconds. The brightness is reduced.p.4Notep.4Cleaning and maintenancep.4: Risk of burns!p.4: Risk of electric shock!p.4: Risk of electric shock!p.4: Risk of injury!p.4Cleaning agentsp.4Observe the information in the table to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent. Do not usep.4Wash new sponge cloths thoroughly before use.p.4Follow all instructions and warnings included with the cleaning agents.p.4Cleaning the metal mesh grease filtersp.5These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.p.5: Risk of fire!p.5Notesp.5By hand:p.5Notep.5In the dishwasher:p.5Notep.5Removing metal grease filterp.51. Fold the filter cover upwards.p.5Notesp.52. Remove the two metal grease filters under the filter cover and the metal grease filter on the underside of the appliance.p.5Unfasten the lock, fold the metal filter forwards and remove it from the bracket.p.5Notep.53. Clean the metal grease filter.p.54. After removing the filters, clean the inside of the appliance.p.55. Clean the filter cover.p.5Installing the metal mesh grease filterp.51. Insert the two metal grease filters under the filter cover with the lock facing downwards.p.52. Fold the metal grease filters inwards, locking them in place.p.53. Close the filter cover.p.5Changing the activated charcoal filter (only in circulating-air mode)p.5In order to guarantee efficient odour filtration, the filter must be serviced regularly.p.5The activated charcoal filters must be replaced at least every 4 months.p.5Notesp.51. Remove metal grease filter: See above.p.52. Turn the old activated charcoal filter and pull away from the bracket. ¨p.53. Push the new activated charcoal filter onto the bracket and turn. ©p.54. Fit the metal grease filter: See above.p.5Trouble shootingp.6Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service.p.6: Risk of electric shock!p.6Malfunction tablep.6Replacing bulbsp.6: Risk of electric shock!p.6Replacing halogen bulbsp.6Notep.61. Carefully remove the bulb ring using a suitable tool.p.62. Pull out the bulb and replace it with a bulb of the same type.p.63. Insert the bulb cover.p.64. Insert the mains plug or switch on the fuse again.p.6Replace the bulb with one of the same type:p.6Voltage: 12 Vp.6Power: max. 20 Wp.6After-sales servicep.6Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.p.6When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter ...p.6You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.p.6Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.p.6Please find the contact data of all countries in the enclosed customer service list.p.6Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.p.6Accessories for circulated air modep.6(not included in the delivery)p.6
Page 1 of the Constructa CD669862 user manual — : Important safety information
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents [en]Instruction manual

Lighting 12 Cleaning and maintenance 12 Trouble shooting 14 After-sales service 14 Accessories for circulated air mode 14

Produktinfo

Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards. Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable.

Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney).

Page 2 of the Constructa CD669862 user manual — Risk of electric shock! ■ Do not use any high-pressure cleaners or
Page 2 · cliquer pour agrandir
Page 2

In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

  • Adequate incoming air must therefore

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of fire! ■ Operating several gas burners at the

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Risk of electric shock!

Risk of fire!

  • A defective appliance may cause electric

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

  • Grease deposits in the grease filter may

catch fire. Clean the grease filter at least every 2 months.

Never operate the appliance without the grease filter.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Risk of electric shock! ■ Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

Risk of fire!

Page 3 of the Constructa CD669862 user manual — Exhaust air mode
Page 3 · cliquer pour agrandir
Page 3

Causes of damage

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

Environmental protection

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

so that the extractor hood can work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the intensity of the cooking fumes.

Only use intensive mode where this is required. A lower fan speed means that less energy is consumed.

  • If there are intensive cooking fumes, select a higher fan

speed in good time. If cooking fumes have already spread in the kitchen, the extractor hood must be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and, if required, replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Operating modes

This appliance can be used in exhaust-air mode or circulating- air mode.

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Exhaust air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

Note: To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Page 4 of the Constructa CD669862 user manual — : Risk of injury!
Page 4 · cliquer pour agrandir
Page 4

Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Fan run-on time

The fan run-on is possible in any fan speed.

1. First, press the button for the required fan speed 1, 2 or 3.
2. To activate the fan run-on, press and hold the % button for 2 seconds. To confirm the setting, the 0 button and the set fan speed flash.
3. To end the fan run-on early, press the 0 button.
  • The run-on time for all fan speeds is 30 minutes. Once this

time has elapsed, the ventilation and lighting automatically switch off.

  • The fan speed can be changed during the run-on time.

Intensive setting

You can use the intensive setting if there is a large build-up of odours and fumes/vapours.

1. To activate the intensive setting, press and hold the g button for 2 seconds. To confirm the setting, the 0 button lights up and the g button flashes.

1 Fan speed 1

2 Fan speed 2

2. To end the intensive setting early, press the 0 button.

3 Fan speed 3

Setting the fan

Lighting

The lighting can be switched on and off independently of the ventilation.

Press the @ button.

Press button 1, 2 or 3.

When switching on the lights, press and hold the @ button for 2 seconds. The brightness is reduced.

To confirm the setting, the 0 button and the set fan speed light up.

Switching off the appliance

Press the 0 button.

Cleaning and maintenance

: Risk of burns!

Cleaning agents

The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

Observe the information in the table to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent. Do not use

: Risk of electric shock!

  • harsh or abrasive cleaning agents,

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

  • cleaning agents with a high concentration of alcohol,
  • hard scouring pads or sponges,
  • high-pressure cleaners or steam cleaners.

: Risk of electric shock!

Wash new sponge cloths thoroughly before use.

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Follow all instructions and warnings included with the cleaning agents.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

Show 8 more labels / short text on this page
Control panel · Explanation · 0 Fan off · % Fan run-on · g Intensive setting · A Light on/off · Switching on · Setting the brightness
Page 5 of the Constructa CD669862 user manual — Changing the activated charcoal filter (only in circulating-air mode)
Page 5 · cliquer pour agrandir
Page 5

Removing metal grease filter

1. Fold the filter cover upwards.

Stainless steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth.

  • The opening angle of the filter cover is restricted to approx.

Clean stainless steel surfaces in the direction of the grain only.

80°. Do not open the filter cover any further, otherwise the hinges may be damaged.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.

  • The filter cover locks in any position.
2. Remove the two metal grease filters under the filter cover and the metal grease filter on the underside of the appliance. Unfasten the lock, fold the metal filter forwards and remove it from the bracket.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

Do not use any stainless steel cleaners.

Constructa CD669862 — Removing metal grease filter diagram (page 5)
Fig. 1 · Removing metal grease filter

Glass cleaner: Clean with a soft cloth.

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Operating controls Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth.

Risk of damage to the electronics from penetrating moisture. Never clean oper- ator controls with a wet cloth.

3. Clean the metal grease filter.

Do not use any stainless steel cleaners.

4. After removing the filters, clean the inside of the appliance.

Cleaning the metal mesh grease filters

5. Clean the filter cover.

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Installing the metal mesh grease filter

1. Insert the two metal grease filters under the filter cover with the lock facing downwards. Insert the metal grease filters on the underside of the appliance.

Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.

2. Fold the metal grease filters inwards, locking them in place.
3. Close the filter cover.

Changing the activated charcoal filter (only in circulating-air mode)

  • Do not use any aggressive, acidic or alkaline cleaning

agents.

  • When cleaning the metal mesh grease filters, also clean the

In order to guarantee efficient odour filtration, the filter must be serviced regularly.

holder for the metal mesh grease filters in the appliance using a damp cloth.

The activated charcoal filters must be replaced at least every 4 months.

  • The metal mesh grease filters can be cleaned in the

dishwasher or by hand.

By hand:

  • The activated charcoal filters are not included in the delivery.

The activated charcoal filters can be obtained from specialist retailers, from our after-sales service or from the Online Shop.

  • The activated charcoal filters cannot be cleaned or
  • Soak the metal mesh grease filters in a hot soapy solution.

reactivated.

  • Clean the filters with a brush and then rinse them thoroughly.
1. Remove metal grease filter: See above.
  • Leave the metal mesh grease filters to drain.
2. Turn the old activated charcoal filter and pull away from the bracket. ¨

In the dishwasher:

3. Push the new activated charcoal filter onto the bracket and turn. ©
Constructa CD669862 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 2 · Changing the activated charcoal filter (only in circ…
  • Do not clean heavily soiled metal mesh grease filters together

with utensils.

  • Place the metal mesh grease filters loosely in the dishwasher.

The metal mesh grease filters must not be wedged in.

4. Fit the metal grease filter: See above.

Area Cleaning agents · Aluminium and plas- tic

Page 6 of the Constructa CD669862 user manual — CZ5139X5
Page 6 · cliquer pour agrandir
Page 6

Trouble shooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

Replacing bulbs : Risk of electric shock!

When changing the bulbs, the bulb socket contacts are live. Before changing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

1. Carefully remove the bulb ring using a suitable tool. 2. Pull out the bulb and replace it with a bulb of the same type.

Power cut Check whether other kitchen appliances are working

Constructa CD669862 — Malfunction table diagram (page 6)
Fig. 3 · Malfunction table

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The button illu- mination does not work.

The control unit is faulty.

Call the aftersales service.

3. Insert the bulb cover.

The lighting does not work.

The bulbs are faulty.

For information on chang- ing the bulbs, see the "Replacing Bulbs" section.

4. Insert the mains plug or switch on the fuse again.

Replace the bulb with one of the same type:

Voltage12 V
Powermax. 20 W
SocketG4

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.

E no. FD no.

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

Please find the contact data of all countries in the enclosed customer service list.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Accessories for circulated air mode

(not included in the delivery)

CZ5139X5

Constructa CD669862 — CZ5139X5 diagram (page 6)
Fig. 4

Replacing halogen bulbs · · After-sales serviceO

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD669862

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD669862

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD669862 manuel PDF

32 pages·1.4 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…