FR
Constructa logo
Notice d'utilisation officielle

Constructa CD649651

40 pages·2.2 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD649651
Table des matières 127 sections Ú Table of contents · Instructions for use · Environmental protection · m Safety instructions · … AfficherMasquer
Ú Table of contentsp.1Instructions for usep.1Environmental protectionp.1m Safety instructionsp.2General informationp.2Danger of suffocation!p.2Installationp.2Mortal danger, risk of intoxication!p.2Risk of fire!p.2Caution!p.2Risk of electric shock!p.2Risk of fire, risk of injury!p.2Risk of injury!p.2Risk of injury!p.2Using the appliancep.2Risk of burns!p.2Risk of injury, risk of damage!p.2Risk of fire, risk of burns!p.2Risk of burns, risk of damage!p.3Risk of fire!p.3Caution!p.3Risk of injury!p.3Cleaning and carep.3Risk of burns, risk of electric shock!p.3Caution!p.3Maintenance and repairp.3Risk of fire, risk of injury!p.3Risk of injury!p.3Risk of fire, risk of injury!p.3Risk of burns, risk of electric shock!p.3Operating modesp.3Exhaust air modep.3Notep.3Circulating-air modep.3Notep.3Operationp.4Notep.4Control panel variant 1p.4Control panel variant 2p.4Switching on fan: variant 1p.4Intensive settingp.4Fan run-onp.4Switching on fan: variant 2p.4Lightp.4Installing and removing filterp.4m Risk of burns, risk of electric shock!p.4Removing metal-mesh grease filterp.41. Open lock and fold down the metal-mesh grease filter.p.42. Take metal-mesh grease filter out of the holder.p.4With edge extractionp.41. Pull metal-mesh grease filter downwards.p.42. Take metal-mesh grease filter out of the holder.p.4Notesp.4Installing metal-mesh grease filterp.41. Insert metal-mesh grease filter.p.42. Fold up metal-mesh grease filter and lock.p.4Cleaning and carep.5m Risk of burns, risk of electric shock!p.5Caution!p.5Cleaning appliance surfacep.5Notep.5Cleaning metal-mesh grease filtersp.5Notesp.5In the dishwasher:p.5Notep.5By hand:p.5Notep.5Replacing bulbsp.5m Risk of burns, risk of electric shock!p.5Replacing halogen bulbsp.5Notep.51. Carefully remove bulb ring using a suitable tool.p.52. Pull out bulb and replace with bulb of the same type.p.53. Insert bulb cover.p.54. Insert mains plug or switch on fuse again.p.5Replacing filament bulbsp.51. Lift bulb cover slightly and push towards the outside of the appliance.p.52. Unscrew bulb and replace with bulb of the same type.p.53. Insert bulb cover.p.54. Insert mains plug or switch on fuse again.p.5LED lightsp.5m Risk of injury!p.5Installation instructionsp.6Safety notesp.6m Mortal danger, risk of intoxication!p.6m Risk of fire!p.6m Risk of electric shock!p.6m Risk of injury!p.6m Risk of injury!p.6Installationp.7Pipe dimensionsp.7Notep.7Checking the wallp.7Preparing the installationp.71. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.p.72. Mark positions for the screws and the contour of the attachment area.p.73. Drill five 8 mm Ø holes to a depth of 80 mm for the attachments and press in the wall plugs flush with the wall.p.7Installationp.71. Screw on the fixing bracket for the flue duct. ¨p.72. Screw on brackets for the extractor hood hand-tight, max. 3 Nm. ©p.83. Screw in threaded pin, leaving it protruding out of the wall by 5–9 mm. ªp.8Attaching and aligning the appliancep.81. Initially remove the protective foil from the back of the appliance and, following installation, remove foil completely.p.82. When attaching the appliance, ensure that it engages firmly with the brackets. «p.83. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬p.8Securing the appliancep.81. Press the safety caps with the arrow upwards onto the brackets until they engage. ®p.82. Screw on knurled nut and washer firmly. ¯p.8Removing safety capsp.9Connecting the pipesp.9Notep.9Exhaust-air pipe Ø 120 mmp.91. Attach reducing connector directly to the air-pipe connector.p.92. Attach exhaust air pipe to the reducing connector.p.93. Seal both joints appropriately.p.9Electrical connectionp.9m Risk of electric shock!p.9Attaching flue ductp.9m Risk of injury!p.91. Separate the flue ducts.p.92. Remove the protective foil from both flue ducts.p.93. Push one flue duct into the other.p.9Notesp.94. Place flue ducts on the appliance.p.95. Push inner flue duct upwards and attach to the fixing brackets on the left and right. ¨p.96. Press flue duct downwards until it engages. ©p.97. Screw flue duct to the sides of the fixing bracket using two screws. ªp.9
Page 1 of the Constructa CD649651 user manual — Ú Table of contents
Page 1 · cliquer pour agrandir
Page 1

Replacing bulbs 15

Installation instructions 16

Safety notes 16

Installation 17

Pipe dimensions 17

Checking the wall 17

Preparing the installation 17

Installation 17

Attaching flue duct 19

European Directive 2002/96/EU concerning used

This appliance is labelled in accordance with the

guideline determines the framework for the return

waste electrical and electronic equipment). The

and recycling of used appliances as applicable.

electrical and electronic appliances (WEEE –

Environmental protection

Instructions for use 11

Environmental protection 11

Safety instructions 12

Operating modes 13

Exhaust air mode 13

Circulating-air mode 13

Operation 14

Installing and removing filter 14

Cleaning and care 15

parts and services can be found at www.constructa.de and in

Produktinfo Additional information on products, accessories, replacement

Trust the expertise of the manufacturer, and rest assured that

Please find the contact data of all countries in the enclosed

the repair will be carried out by trained service technicians

using original spare parts for your domestic appliance.

the online shop www.constructa-eshop.com

Ú Table of contents

Instructions for use

customer service list..

Page 2 of the Constructa CD649651 user manual — Installation
Page 2 · cliquer pour agrandir
Page 2
Constructa CD649651 — m Safety instructions diagram (page 2)
Fig. 1 · m Safety instructions

Unrestricted operation is possible if the vapour extractor hood

Risk of damage from heat accumulation due to too narrow gap

of the appliance may be installed directly next to a high-sided

unit or a wall. Distance between the appliance and wall or high-

The specified safety distances must be observed. Also observe

regulations and the regulations of the local electricity and gas

from damaged connection cable. A damaged connection cable

from a falling appliance. All safety screws and safety caps must

from hot appliance when used with cooking appliances. Keep

use gas hotplates with appropriate cooking utensils. Regulate

incoming/exhaust air wall boxes or by other technical means.

from flying sparks. Do not install appliance above a solid fuel

between appliance and high-sided unit or wall. Only one side

and electric hobs are operated together, the largest specified

From sharp edges during installation. Always wear protective

In any case, consult your responsible chimney sweep. He is

heater (e.g. wood or coal) unless a closed, non-removable

flame to ensure that it does not lick over the cooking utensil.

able to assess the house's entire ventilation setup and will

from objects falling on the appliance. Never place objects

if gas hotplates not covered with cooking utensils. Always

The width of the extractor hood must correspond at least

that cannot be sealed, for example in doors, windows,

from damaged connection cable. Do not kink or pinch

must be replaced by a qualified technician (electrician).

For the installation observe the currently valid building

children away and ensure appliance is used properly.

the specifications for your cooking appliance. If gas

suggest the suitable ventilation measures to you.

is operated exclusively in the recirculation mode.

connection cable during installation.

gloves while installing the appliance.

sided unit must be at least 50 mm.

Risk of injury, risk of damage!

Using the appliance

Risk of fire, risk of injury!

Risk of fire, risk of burns!

with the width of the hob.

Risk of electric shock!

cover is available.

on the appliance.

distance applies.

be firmly fitted.

suppliers.

The appliance can only be used safely if it is correctly installed

Do not connect the appliance if it has been damaged in transit.

Adults and children must never use the appliance unsupervised

the appliance (to do this, remove the metal-mesh grease filter).

Enter the numbers in the above box so that you can easily find

appliance in the exhaust air mode at the same time as a room

Constructa CD649651 — Using the appliance diagram (page 2)
Fig. 2 · Using the appliance

partial vacuum is produced if not enough fresh air is supplied.

Safe operation is possible only whenever the partial vacuum in

exceed 4 Pa (0.04 mbar). This can be achieved whenever the

Follow these instructions, in particular the safety instructions.

Due to combustion gases sucked back in. Never operate the

Room air-dependent heat-producing appliances (e.g. gas, oil,

water heaters) obtain combustion air from the room in which

In combination with an activated vapour extractor hood, room

air needed for combustion is able to enter through openings

Please contact our customer service regarding any queries

air-dependent heat-producing appliance unless an adequate

they are installed and discharge the exhaust gases into the

air is extracted from the kitchen and neighbouring rooms - a

  • Adequate incoming air must therefore always be ensured.

according to the safety instructions. Retain the instructions

The manufacturer is not liable for damage which is caused

After unpacking the appliance, check it for visible damage.

wood or coal-operated heaters, continuous flow heaters or

This appliance is designed to be used in the home only.

It is possible that individual features are described which

if they are not physically or mentally capable of doing so

Toxic gases from the chimney or the extraction shaft are

  • An incoming/exhaust air wall box alone will not ensure

the place where the firing equipment is installed does not

or if they lack the knowledge and experience to operate

from packaging material. Never allow children to play

These instructions apply to several appliance models.

open through an exhaust gas system (e.g. a chimney).

The numbers can be found on the rating plate inside

When calling, please quote the following numbers:

Never allow children to play with the appliance!

or faults (see list of customer service centres).

ã= Safety instructions

for subsequent use or for the next owner.

by improper use or incorrect operation.

sucked backed into the living space.

E-Nr. FD

Mortal danger, risk of intoxication!

the appliance correctly and safely.

do not apply to your appliance.

supply of fresh air is ensured.

General information

compliance with the limit.

with packaging material.

them when required.

Installation

Show 4 more labels / short text on this page
Risk of injury! · Risk of injury! · Risk of burns! · Risk of fire!
Page 3 of the Constructa CD649651 user manual — Exhaust air mode
Page 3 · cliquer pour agrandir
Page 3
  • Risk of damage due to ingress of humidity into the electronic
  • Surface damage due to strong or abrasive cleaning agents.

from damaged connection cable. A damaged connection cable

by the grease filters and an activated carbon filter

or from the Online Shop. The accessory numbers can be found

  • Surface damage due to incorrect cleaning. Clean stainless

from improper repairs. Switch off fuse or pull out mains plug.

from defective or damaged appliance. Switch off fuse or pull

in the brochure or ask your dealer. The required accessories

from defective bulbs. Switch off fuse or pull out mains plug.

an activated carbon filter. The different options of operating

are available from specialist outlets, from customer service

steel surfaces in the grind direction only. Do not use any

circuitry. Never clean operator controls with a wet cloth.

Always replace defective bulbs immediately (leave bulbs

must be replaced by a qualified technician (electrician).

to cool down first) to prevent the remaining bulbs from

Repairs may be performed by a qualified technician

the appliance in circulating-air mode can be found

Never use strong and abrasive cleaning agents.

The air which is drawn in is cleaned

and conveyed back into the kitchen.

stainless steel cleaners for operator controls.

out mains plug and call customer service.

Risk of burns, risk of electric shock!

at the end of the instructions for use.

Maintenance and repair

Circulating-air mode

Risk of fire, risk of injury!

Risk of fire, risk of injury!

(electrician) only.

overloading.

operate two gas hotplates simultaneously on the highest flame

grease filters and conveyed to the exterior by a

smoke or exhaust gas flue, obtain the consent of the heating

for longer than 15 minutes. The housing will become very hot

  • from grease deposits in the metal-mesh grease filter. Never

(e.g. flambéing). Always operate appliance with metal-mesh

due to LED lights of risk group 1. Do not look directly into the

This appliance can be used in exhaust-air mode or circulating-

if several gas hotplates are operated simultaneously. Never

constant supervision only. Never extinguish fire with water,

appliance while cooking to avoid condensation. Condensate

from appliance. Always leave appliance to cool down before

cleaning or servicing. Switch off fuse or pull out mains plug.

The air which is drawn in is cleaned by the

ventilate installation rooms which contain heating appliances.

grease filter. Regularly clean the metal-mesh grease filter.

smoke or exhaust gas flue or into a shaft which is used to

  • from overheated fats and oils. Heat fats and oils under
  • Before conveying the exhaust air into a non-functioning
  • If the exhaust air is conveyed through the outer wall, a

Risk of damage due to corrosion. Always switch on the

switched on LED lights for longer than 100 seconds.

work under the appliance with a naked flame

always use a fire blanket, lid or plate.

telescopic wall box should be used.

Risk of burns, risk of electric shock!

Operating modes

to the power of two gas burners.

can produce corrosion damage.

Risk of burns, risk of damage!

pipe system.

Cleaning and care

due to the intense heat.

Exhaust air mode

engineer responsible.

air mode.

Risk of injury! · Risk of injury! · Risk of fire!

Page 4 of the Constructa CD649651 user manual — Operation
Page 4 · cliquer pour agrandir
Page 4

You can use the Intensive setting for particularly strong odour

Keep pressing button A until – is indicated on the display. The

1. Pull metal-mesh grease filter downwards. In doing so, place other hand under the metal-mesh grease

– Do not hold metal-mesh grease filter at an angle, otherwise

1. Insert metal-mesh grease filter. In doing so, place other hand under the metal-mesh grease

Keep pressing button @ until ˜ / › is indicated on the display.

The light can be switched on and off independently of the fan.

  • Grease can accumulate in the bottom of the metal-mesh

Run time is limited. Then the appliance sets automatically a

run time is limited. The appliance runs for 10 minutes at fan

lower fan setting. You can always switch back manually.

Increase fan setting by pressing button @ or reduce

2. Take metal-mesh grease filter out of the holder.

Increase or reduce the fan settings by pressing

Installing metal-mesh grease filter

2. Fold up metal-mesh grease filter and lock.

setting 1 and then switches off by itself.

Switching on fan: variant 1

Switching on fan: variant 2

Constructa CD649651 — Switching on fan: variant 1 diagram (page 4)
Fig. 3 · Switching on fan: variant 1

it by pressing button A.

grease will drip out.

and fume generation.

Press On/Off button.

buttons 1, 2 and 3.

grease filter.

Light

filter.

filter.

cooking. This is the most effective way of removing the kitchen

Constructa CD649651 — Light diagram (page 4)
Fig. 4 · Light
Constructa CD649651 — Light diagram (page 4)
Fig. 5 · Light
Constructa CD649651 — Light diagram (page 4)
Fig. 6 · Light
Constructa CD649651 — Light diagram (page 4)
Fig. 7 · Light

and switch it off again several minutes after you have finished

from appliance. Always leave appliance to cool down before

1. Open lock and fold down the metal-mesh grease filter. In doing so, place other hand under the metal-mesh grease

Installing and removing filter

cleaning or servicing. Switch off fuse or pull out mains plug.

It is possible that individual features are described which

These instructions apply to several appliance models.

Removing metal-mesh grease filter

2. Take metal-mesh grease filter out of the holder.

ã= Risk of burns, risk of electric shock!

do not apply to your appliance.

Constructa CD649651 — ã= Risk of burns, risk of electric shock! diagram (page 4)
Fig. 8 · ã= Risk of burns, risk of electric shock!

Control panel variant 1

Control panel variant 2

Operation

fumes.

filter.

With edge extraction · Intensive setting · Fan run-on

Page 5 of the Constructa CD649651 user manual — Cleaning appliance surface
Page 5 · cliquer pour agrandir
Page 5

particles from the kitchen fumes. Clean the metal-mesh grease

filters under normal use (1 to 2 hours daily) approx. every three

the holder for the metal-mesh grease filters in the appliance

in the dishwasher, slight discolouration may occur. This has no

  • Do not clean heavily soiled metal-mesh grease filters together
  • Clean the filters with a brush and then rinse them thoroughly.
Constructa CD649651 — Cleaning and care diagram (page 5)
Fig. 9 · Cleaning and care

Defective LED lights may be replaced by the manufacturer, his

due to LED lights of risk group 1. Do not look directly into the

  • Soak the metal-mesh grease filters in a hot soapy solution.
1. Lift bulb cover slightly and push towards the outside of the appliance.

customer service or a qualified technician (electrician) only.

The inserted metal-mesh grease filters absorb the grease

  • When cleaning the metal-mesh grease filters, also clean
  • Do not use any aggressive, acidic or alkaline cleaning

in the dishwasher. The metal-mesh greases filter must

2. Unscrew bulb and replace with bulb of the same type.

effect on the function of the metal-mesh grease filters.

switched on LED lights for longer than 100 seconds.

Cleaning metal-mesh grease filters

  • The metal-mesh grease filters can be cleaned
  • Leave the metal-mesh grease filters to drain.
  • Place the metal-mesh grease filters loosely
4. Insert mains plug or switch on fuse again.

It can be ordered via the Online Shop.

Replacing filament bulbs

in the dishwasher or by hand.

Constructa CD649651 — Replacing filament bulbs diagram (page 5)
Fig. 10 · Replacing filament bulbs

using a damp cloth.

not be wedged in.

In the dishwasher:

3. Insert bulb cover.

ã= Risk of injury!

with utensils.

LED lights

agents.

By hand:

months.

  • Risk of damage due to ingress of humidity into the electronic

Suitable cleaning agents and care products for your appliance

can be purchased via the Hotline or from the Online Shop (see

  • Clean the surfaces with a soft, damp cloth, washing-up liquid

or a mild window cleaner. Soften dried dirt with a damp cloth.

  • Surface damage due to incorrect cleaning. Clean stainless
  • Surface damage due to strong or abrasive cleaning agents.

from appliance. Always leave appliance to cool down before

cleaning or servicing. Switch off fuse or pull out mains plug.

agents containing sand, soda, acid, chlorine or any other

from defective bulbs. Switch off fuse or pull out mains plug.

steel surfaces in the grind direction only. Do not use any

  • Dry cloths, abrasive sponges, scouring agents, cleaning

circuitry. Never clean operator controls with a wet cloth.

Observe the warranty regulations in the enclosed service

Always replace defective bulbs immediately (leave bulbs

to cool down first) to prevent the remaining bulbs from

(see bulb holder or rating plate inside the appliance) –

2. Pull out bulb and replace with bulb of the same type.
  • Clean the stainless steel surfaces in the direction

tube. Use a clean cloth to insert the halogen bulbs.

Never use strong and abrasive cleaning agents.

  • Do not use stainless steel cleaner or wet cloths
1. Carefully remove bulb ring using a suitable tool.

stainless steel cleaners for operator controls.

booklet and the following cleaning instructions:

4. Insert mains plug or switch on fuse again.

to do this remove metal-mesh grease filter.

ã= Risk of burns, risk of electric shock!

aggressive substances are not suitable.

ã= Risk of burns, risk of electric shock!

Cleaning and care

Cleaning appliance surface

Replacing bulbs

Replacing halogen bulbs

front of the instructions for use).

Constructa CD649651 — Cleaning appliance surface diagram (page 5)
Fig. 11 · Cleaning appliance surface

of the ground surface only.

3. Insert bulb cover.

for the controls.

overloading.

Do not scratch!

Page 6 of the Constructa CD649651 user manual — Safety notes
Page 6 · cliquer pour agrandir
Page 6
Constructa CD649651 — Installation instructions diagram (page 6)
Fig. 12 · Installation instructions
  • The surfaces of the appliance are sensitive. Avoid damaging

Unrestricted operation is possible if the vapour extractor hood

regulations and the regulations of the local electricity and gas

from a falling appliance. All safety screws and safety caps must

from flying sparks. Do not install appliance above a solid fuel

From sharp edges during installation. Always wear protective

  • Follow the enclosed installation instructions for additional

In any case, consult your responsible chimney sweep. He is

heater (e.g. wood or coal) unless a closed, non-removable

able to assess the house's entire ventilation setup and will

from damaged connection cable. Do not kink or pinch

For the installation observe the currently valid building

special accessories (e.g. for circulating-air mode).

suggest the suitable ventilation measures to you.

is operated exclusively in the recirculation mode.

  • This appliance is installed on the wall.

connection cable during installation.

gloves while installing the appliance.

ã= Risk of electric shock!

them during installation.

ã= Risk of injury!

ã= Risk of injury!

cover is available.

ã= Risk of fire!

be firmly fitted.

suppliers.

Constructa CD649651 — ã= Risk of fire! diagram (page 6)
Fig. 13 · ã= Risk of fire!

appliance in the exhaust air mode at the same time as a room

Constructa CD649651 — ã= Risk of fire! diagram (page 6)
Fig. 14 · ã= Risk of fire!

partial vacuum is produced if not enough fresh air is supplied.

Safe operation is possible only whenever the partial vacuum in

exceed 4 Pa (0.04 mbar). This can be achieved whenever the

Constructa CD649651 — ã= Risk of fire! diagram (page 6)
Fig. 15 · ã= Risk of fire!

Due to combustion gases sucked back in. Never operate the

Room air-dependent heat-producing appliances (e.g. gas, oil,

water heaters) obtain combustion air from the room in which

In combination with an activated vapour extractor hood, room

air needed for combustion is able to enter through openings

incoming/exhaust air wall boxes or by other technical means.

air-dependent heat-producing appliance unless an adequate

they are installed and discharge the exhaust gases into the

air is extracted from the kitchen and neighbouring rooms - a

  • Adequate incoming air must therefore always be ensured.

wood or coal-operated heaters, continuous flow heaters or

Toxic gases from the chimney or the extraction shaft are

  • An incoming/exhaust air wall box alone will not ensure

the place where the firing equipment is installed does not

open through an exhaust gas system (e.g. a chimney).

that cannot be sealed, for example in doors, windows,

Installation instructions

ã= Mortal danger, risk of intoxication!

sucked backed into the living space.

supply of fresh air is ensured.

compliance with the limit.

Safety notes

Page 7 of the Constructa CD649651 user manual — Checking the wall
Page 7 · cliquer pour agrandir
Page 7
Constructa CD649651 — Installation diagram (page 7)
Fig. 16 · Installation
Constructa CD649651 — Installation diagram (page 7)
Fig. 17 · Installation
3. Drill five 8 mm Ø holes to a depth of 80 mm for the attachments and press in the wall plugs flush with
1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.
2. Mark positions for the screws and the contour of the attachment area.
1. Screw on the fixing bracket for the flue duct. ¨

Preparing the installation

Installation

the wall.

  • The device achieves its optimum performance by means of a

short, straight exhaust air pipe and as large a pipe diameter

  • As a result of long rough exhaust air pipes, many pipe bends

The inner cross-section must correspond to the diameter of the

  • The wall must be level, vertical and adequately load-bearing.
  • The enclosed screws and wall plugs are suitable for solid

or diameters, the optimum extraction performance is not

  • The pipes or hoses for laying the exhaust air line must

as the screws. The wall plugs must have a secure grip.

structures (e.g. plasterboard, porous concrete, poroton

  • The depth of the boreholes must be the same length

An inner diameter of 150 mm, but at least 120 mm, is

brickwork. Suitable fasteners must be used for other

  • The max. weight of the extractor hood is 40 kg .
  • Use sealing strip for deviating pipe diameters.

for complaints attributable to the pipe section.

  • Flat ducts should have no sharp deflections.

achieved and fan noise is increased.

consist of non-combustible material.

Ø 150 mm approx. 177 cm2

Ø 120 mm approx. 113 cm2

Checking the wall

Installation

Pipe dimensions

recommended.

as possible.

round pipes.

bricks).

Round pipes · Flat ducts

Page 8 of the Constructa CD649651 user manual — !
Page 8 · cliquer pour agrandir
Page 8
2. When attaching the appliance, ensure that it engages firmly with the brackets. «
3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬
Constructa CD649651 — 2. Screw on brackets for the extractor hood hand-tight, max. 3 Nm. © diagram (page 8)
Fig. 18 · 2. Screw on brackets for the extractor hood hand-tig…
1. Initially remove the protective foil from the back of the appliance and, following installation, remove foil
1. Press the safety caps with the arrow upwards onto the brackets until they engage. ®
Constructa CD649651 — 2. Screw on brackets for the extractor hood hand-tight, max. 3 Nm. © diagram (page 8)
Fig. 19 · 2. Screw on brackets for the extractor hood hand-tig…

Attaching and aligning the appliance

Constructa CD649651 — Attaching and aligning the appliance diagram (page 8)
Fig. 20 · Attaching and aligning the appliance
2. Screw on knurled nut and washer firmly. ¯

!

completely.

Constructa CD649651 — ! diagram (page 8)
Fig. 21
3. Screw in threaded pin, leaving it protruding out of the wall by 5–9 mm . ª
Constructa CD649651 — ! diagram (page 8)
Fig. 22
2. Screw on brackets for the extractor hood hand-tight, max. 3 Nm . ©

Securing the appliance

Page 9 of the Constructa CD649651 user manual — ã= Risk of injury!
Page 9 · cliquer pour agrandir
Page 9
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 23 · Removing safety caps
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 24 · Removing safety caps
7. Screw flue duct to the sides of the fixing bracket using two screws. ª
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 25 · Removing safety caps
  • To prevent scratches, place paper for protection over
5. Push inner flue duct upwards and attach to the fixing brackets on the left and right. ¨
2. Remove the protective foil from both flue ducts.
6. Press flue duct downwards until it engages. ©

– Slots of the inner flue duct downwards.

1. Separate the flue ducts. To do this, remove the adhesive tape.

the edges of the outer flue duct.

4. Place flue ducts on the appliance.
3. Push one flue duct into the other.
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 26 · Removing safety caps
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 27 · Removing safety caps
Constructa CD649651 — Removing safety caps diagram (page 9)
Fig. 28 · Removing safety caps

The required connection data can be found on the rating plate

inside the appliance; to do this, remove the metal-mesh grease

1. Attach reducing connector directly to the air-pipe connector.

This appliance complies with the EC interference suppression

  • The earthed socket should be connected via its own circuit.

The permanent connection may be installed by an electrician

From sharp edges during installation. Always wear protective

If the safety caps have to be removed, use a flat screwdriver.

installation of the appliance, a disconnector must be fitted

If a permanent connection is required, the installation must

This appliance may be connected to a correctly installed

Attach exhaust-air pipe directly to the air-pipe connector

Attach the earthed socket preferably inside the flue duct.

  • If the earthed socket is no longer accessible following

feature an all-pole disconnector (circuit breakers, fuses

from damaged connection cable. Do not kink or pinch

2. Attach exhaust air pipe to the reducing connector.

and contactors) with a min. 3 mm contact opening.

Exhaust-air pipe Ø 150 mm (recommended size)

Length of the connection cableapprox. 1.30 m

gloves while installing the appliance.

connection cable during installation.

as for a permanent connection.

3. Seal both joints appropriately.

Connecting the pipes

Electrical connection

Exhaust-air pipe Ø 120 mm

ã= Risk of electric shock!

Attaching flue duct

earthed socket only.

ã= Risk of injury!

beforehand.

regulations.

and seal.

filter.

only.

Removing safety caps

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD649651

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD649651

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD649651 manuel PDF

40 pages·2.2 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…