FR
Constructa logo
Notice d'utilisation officielle

Constructa CD646850

56 pages·2.5 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD646850
Table des matières 192 sections Ú Table of contents[en] Instructions for installation and use · Instruction manual · : Intended useIntended use · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Intended useIntended usep.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their sa...p.1Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1: Important safety informationImportant safety informationp.2Danger of suffocation!p.2Packaging material is dangerous to children. Never allow children to play with packaging material.p.2Danger of death!p.2Risk of poisoning from flue gases that are drawn back in.p.2Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.2Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2■ The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2■ The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.p.2Risk of injury!p.3■ Components inside the appliance may have sharp edges. Wear protective gloves.p.3■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.3■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.p.3Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.3■ Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.p.3Causes of damagep.3Caution!p.3Caution!p.3Environmental protectionEnvironmental protectionp.4Saving energyp.4Environmentally-friendly disposalp.4Operating modesOperating modesp.4Exhaust air modep.4Notep.4Circulating-air modep.4Notep.4Operating the applianceOperating the appliancep.5Notep.5Control panelp.5Setting the fanp.5Switching onp.5Choosing the fan settingp.5Switching offp.5Intensive settingp.5Switching onp.5Notep.5Switching offp.5Fan run-on timep.5Switching onp.5Switching offp.5Intermittent ventilationp.5Switching onp.5Switching offp.5Saturation displayp.6Notep.6Audible signalp.6Switching onp.6Switching offp.6Lightingp.6Cleaning and maintenanceCleaning and maintenancep.6: Risk of burns!p.6: Risk of electric shock!p.6: Risk of injury!p.6Caution!p.6Cleaning agentsp.6Notep.6Notep.6Removing metal grease filterp.71. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.p.72. Take the metal grease filter out of the holder.p.7Notesp.7Cleaning the metal mesh grease filtersp.7: Risk of fire!p.7Notesp.7By hand:p.7Notep.7In the dishwasher:p.7Notep.7Installing the metal mesh grease filterp.7: Risk of injury!p.7Notep.71. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.p.7Notep.72. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.p.7Trouble shootingTrouble shootingp.8: Risk of electric shock!p.8Malfunction tablep.8LED lightsp.8: Risk of injury!p.8Customer serviceCustomer servicep.8Accessoriesp.8Notep.8Notep.8Installation instructionsp.9: Important safety informationImportant safety informationp.9Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.9Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.9The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.9The surfaces of the appliance are easily damaged. Avoid damaging them during installation.p.9The width of the extractor hood must correspond at least with the width of the hob.p.9For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.9Risk of fire!p.10■ Fatty deposits in the grease filter may catch fire. The specified safety clearances must be complied with in order to prevent a build-up of heat. Refer to the information provided for your cooker. If gas and electric hobs are being operated toget...p.10■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.10When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.p.10Risk of death!p.10Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust ...p.10Danger of death!p.10Risk of poisoning from flue gases that are drawn back in.p.10Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.10Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.10In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.10■ Adequate incoming air must therefore always be ensured.p.10■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.10Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.10In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.10Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.10Danger of death!p.10Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.10Risk of injury!p.10■ Components inside the appliance may have sharp edges. Wear protective gloves.p.10■ The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed firmly and securely.p.10■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.10■ Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.p.10Risk of electric shock!p.11■ Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.11■ It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed.p.11The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of ...p.11The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residualcurrent circuit breaker (RCCB) in the appliance's power supply circuit.p.11Risk of electric shock!p.11Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in ...p.11Danger of suffocation!p.11Packaging material is dangerous to children. Never allow children to play with packaging material.p.11General informationGeneral informationp.11Exhaust air modep.11: Risk of death!p.11Exhaust ductp.11Notep.11Checking the wallp.11Electrical connectionp.11: Risk of electric shock!p.11: Risk of electric shock!p.11InstallationInstallationp.12Preparing the installationp.12Caution!p.121. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.p.122. Use the enclosed template to mark the positions for the screws and the outline of the attachment area.p.123. Drill five 8 mm diameter holes to a depth of 80 mm for fastening the appliance and press in the wall plugs flush with the wall.p.12Installationp.121. Screw on the fixing bracket for the flue duct. ¨p.122. Screw on brackets for the extractor hood hand-tight. Do not firmly tighten the screws. ©p.123. Screw in the threaded bolt, leaving it protruding out of the wall by 5–9 mm. ªp.12Attaching and aligning the appliancep.131. First, remove the protective foil from the back of the appliance and, following installation, remove the foil completely.p.132. When attaching the appliance, ensure that it engages firmly with the brackets. «p.133. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬p.134. Firmly tighten the screws for the brackets. When doing so, hold the brackets securely in place. ®p.135. Firmly tighten the knurled nuts. ¯p.13Connecting the pipesp.13Notep.13Exhaust-air pipe Ø 120 mmp.131. Attach the reducing connector directly to the air-pipe connector.p.132. Attach the exhaust air pipe to the reducing connector.p.133. Seal both joints appropriately.p.13Attaching the flue ductp.13: Risk of injury!p.131. Separate the flue ducts.p.132. Remove the protective foil from both flue ducts.p.133. Push one flue duct into the other.p.13Notesp.134. Place flue ducts on the appliance.p.135. Push the inner flue duct upwards and attach it to the fixing brackets on the left and right. ¨p.136. Press the flue duct downwards until it engages. ©p.137. Screw the flue duct to the sides of the fixing bracket using two screws. ªp.13
Page 1 of the Constructa CD646850 user manual — : Intended use I ntended use
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents[en]I nstructi ons for i nstal l ati on and use

INSTRUCTION MANUAL 16

INSTALLATION INSTRUCTIONS............................................. 24

Intended use 16 Important safety information 17 Environmental protection 19 Operating modes 19 Operating the appliance 20 Cleaning and maintenance 21 Trouble shooting 23 Customer service 23

INSTRUCTION MANUAL

Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Intended use I ntended use

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level.

This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their safety, or have been instructed in how to use the appliance safely and have understood the risks involved in not using it properly. Children must not play with the appliance.Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Page 2 of the Constructa CD646850 user manual — Risk of burns! ■ The appliance becomes hot during
Page 2 · cliquer pour agrandir
Page 2

: Important safety information I mportant safety i nformati on

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Fatty deposits in the grease filter may

catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of fire! ■ When gas burners are in operation without

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

  • Adequate incoming air must therefore

Risk of fire! ■ Operating several gas burners at the

always be ensured.

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of burns!

  • The accessible parts become very hot

when in operation. Never touch hot parts. Keep children at a safe distance.

Risk of burns! ■ The appliance becomes hot during

operation. Allow the appliance to cool down before cleaning.

Page 3 of the Constructa CD646850 user manual — Risk of electric shock! ■ Penetrating moisture may result in an
Page 3 · cliquer pour agrandir
Page 3

Risk of injury!

Causes of damage

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of injury! ■ The light emitted by LED lights is very

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Risk of electric shock!

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

  • A defective appliance may cause electric

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of damage as a result of incorrect loading of design elements. Do not pull design elements.Do not place objects on the design elements or hang objects from them.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

There is a risk of surface damage if you do not peel off the protective film.Remove the protective film from all parts of the appliance before using the appliance for the first time.

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of electric shock! ■ Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

Risk of electric shock! ■ Penetrating moisture may result in an

electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Page 4 of the Constructa CD646850 user manual — Exhaust air mode
Page 4 · cliquer pour agrandir
Page 4

Environmental protection Envi ronmental protecti on

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

to enable the extractor hood to work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the amount of steam produced

during cooking. Only use intensive mode when required. The lower the fan speed, the less energy is consumed.

  • If cooking produces large amounts of steam, select a higher

fan speed in good time. If the cooking steam has already spread around the kitchen, the extractor hood will need to be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and (if required) replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

  • Put the lid on to reduce cooking steam and condensation.

Operating modes Operati ng modes

Exhaust air mode

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Page 5 of the Constructa CD646850 user manual — Setting the fan
Page 5 · cliquer pour agrandir
Page 5

Operating the appliance Operati ng the appl i ance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

Control panel

Intensive setting

You can use the intensive setting if there is a large build-up of odours and fumes/vapours.

Touch the g symbol. ˜ƒ will light up on the display.

A / @ Fan settings

Touch the g symbol again to switch back to intensive mode ˜‚.

g Intensive mode 1/2

z Metal grease filter/ activated charcoal filters

Touch the g symbol to stop intensive mode.

Fan run-on time

Touch the + symbol. + will light up on the display panel.

The fan will run at fan setting 1.

‚ - „ Fan settings

The fan will switch off automatically after approximately 10 minutes.

˜‚ / ˜ƒ Intensive mode 1/2

/ Duration of fan run-on

| Metal grease filter saturation indicator

Touch the + symbol.

{ Activated charcoal filter saturation indicator

This immediately stops the fan run-on.

Setting the fan

Intermittent ventilation

With intermittent ventilation, the fan automatically switches to the lowest setting for 5 minutes every hour.

Touch the # symbol.

The fan will start at fan setting 2.

Choosing the fan setting

Touch the ' symbol. ' will light up on the display panel.

Touch the @ or A symbol to select a different fan setting.

Intermittent ventilation is activated.

The fan setting that is selected will be shown on the display panel.

Touch the ' symbol.

This immediately stops the intermittent ventilation. The fan will run at fan setting 2.

Touch the # symbol.

Show 18 more labels / short text on this page
Symbol Explanation · # Fan on/off · + Run-on · Switching on · ' Intermittent ventilation · N Light on/off/dimming · Switching off · Indicator/ symbol · Explanation · D Home Connect · + Run-on · Switching on · ' Intermittent ventilation · Switching off · Switching on · Switching on · Switching off · Switching off
Page 6 of the Constructa CD646850 user manual — Cleaning agents
Page 6 · cliquer pour agrandir
Page 6

Saturation display

Audible signal

When the metal grease filters or the activated charcoal filter become saturated, the relevant indicator flashes after the appliance is switched off:

With the fan switched off, touch and hold the # and ' symbols at the same time for approximately 3 seconds. A signal will sound as an acknowledgement.

  • Metal grease filters: |
  • Activated charcoal filter: {

When the signal tone is activated, ‚ will be lit.

  • Metal grease filters and activated charcoal filter: | and {

If you have not yet done so, the metal grease filters should now be cleaned or the activated charcoal filter replaced.

With the fan switched off, touch and hold the # and ' symbols at the same time for approximately 3 seconds. A signal will sound as an acknowledgement.

When the signal tone is deactivated, ‹ will be lit.

Lighting

The saturation indicators can be reset while they are flashing. Touch the z symbol to do this.

The lighting can be switched on and off independently of the fan.

Switching over the display for air circulation mode

Touch the N symbol.

For air recirculation mode, the electronic controller must be switched over accordingly:

  • The extractor hood must be connected and switched off.

Press and hold the N symbol until the required brightness is reached.

  • Touch and hold the # and @ symbols at the same time until

"2" lights up for air recirculation mode (filters that cannot be regenerated).

  • Touch and hold the # and @ symbols again at the same time

until "3" lights up for air recirculation mode (filters that can be regenerated).

  • Touch and hold the # and @ symbols again at the same time

until the electronic controller has switched back to air extraction mode (indicator 1 ).

Cleaning and maintenance Cl eani ng and mai ntenance

: Risk of burns!

The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

: Risk of electric shock!

  • Penetrating moisture may result in an electric shock. Clean

Stainless steel Hot soapy water: Clean with a dish cloth and then dry with a soft cloth.

the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Clean stainless steel surfaces in the direction of the grain only.

Risk of electric shock! ■Do not use any high-pressure cleaners or steam cleaners,

which can result in an electric shock. : Risk of injury!

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers.Apply a very thin layer of the cleaning product with a soft cloth.

Components inside the appliance may have sharp edges. Wear protective gloves.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

There is a risk of surface damage if you do not peel off the protective film.Remove the protective film from all parts of the appliance before using the appliance for the first time.

Do not use stainless steel cleaner.

Hot soapy water: Clean with a soft cloth.

Cleaning agents

To ensure that the different surfaces are not damaged by using the wrong cleaning product, follow the instructions in the table. Do not use any of the following:

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

  • Harsh or abrasive cleaning agents, e.g. scouring powder or

Controls Hot soapy water: Clean using a damp dish cloth and then dry with a soft cloth.

  • Cleaning products with a high alcohol content,

Risk of electric shock caused by pene- trating moisture.

  • Hard scouring pads or cleaning sponges,
  • Pressure washers or steam cleaners,

Risk of damage to the electronics caused by penetrating moisture. Never clean controls with a wet cloth.

  • Cleaning products that dissolve limescale,
  • Aggressive all-purpose cleaning products,
  • Oven spray.

Do not use stainless steel cleaner.

Show 7 more labels / short text on this page
Switching on · Switching off · Set brightness · Area Cleaning products · Aluminium and plastic · liquid scouring cleaner, · --------
Page 7 of the Constructa CD646850 user manual — Cleaning the metal mesh grease filters
Page 7 · cliquer pour agrandir
Page 7

Removing metal grease filter

Installing the metal mesh grease filter : Risk of injury!

1. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.

Components inside the appliance may have sharp edges. Wear protective gloves.

2. Take the metal grease filter out of the holder.
Constructa CD646850 — Removing metal grease filter diagram (page 7)
Fig. 1 · Removing metal grease filter
1. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.
2. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.
  • Fat may accumulate in the bottom of the metal grease filter.
  • Hold the metal grease filter level to prevent fat from

dripping out.

Cleaning the metal mesh grease filters

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Risk of fire!

Fatty deposits in the grease filter may catch fire. Regularly clean the grease filter. Never operate the appliance without a grease filter.

  • Do not use aggressive, acidic or alkaline cleaning products.
  • We recommend cleaning the grease filters every 2 months.
  • When cleaning the metal grease filters, also clean the metal

grease filter holder in the appliance using a damp cloth.

  • The metal grease filters can be cleaned in the dishwasher or

by hand.

By hand:

  • Soak the metal grease filters in hot soapy water.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal grease filters to drain on an absorbent

material.

In the dishwasher:

  • Use normal domestic dishwashing detergents.
  • Do not clean heavily soiled metal grease filters together with

cookware.

  • Place the metal grease filters in the dishwasher, leaving

plenty of space around them. Do not trap the metal grease filters.

  • Select a temperature of no more than 70 °C.
Page 8 of the Constructa CD646850 user manual — CZ5170X1
Page 8 · cliquer pour agrandir
Page 8

Trouble shooting Troubl e shooti ng

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

LED lights

Defective LED lights may be replaced by the manufacturer, their customer service or a qualified technician (electrician) only. : Risk of injury!

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The LED lights are defective.

Call the after-sales ser- vice.

The button illu- mination does not work.

The control unit is faulty.

Call the aftersales ser- vice.

Customer service Customer servi ce

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

Accessories

(not included in the scope of delivery)

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

Accessory - narrow 260 mm Order number

E no. FD no.

Starter set for air recirculation mode CZ5101X5

CZ5270X0

Easy-change filter for CleanAir recirculation module (cannot be regenerated)

CZ5170X1

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Accessory - wide 345 mm Order number

Please find the contact data of all countries in the enclosed customer service list.

Starter set for air recirculation mode CZ5102X5

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

CZ5276X0

Easy-change filter for CleanAir recirculation module (cannot be regenerated)

CZ5170X1

Show 5 more labels / short text on this page
CleanAir recirculation module · After-sales serviceO · -------- · CleanAir recirculation module · --------
Page 9 of the Constructa CD646850 user manual — : Important safety information I mportant safety i nformati on
Page 9 · cliquer pour agrandir
Page 9

INSTALLATION INSTRUCTIONS

Constructa CD646850 — INSTALLATION INSTRUCTIONS diagram (page 9)
Fig. 2
Constructa CD646850 — INSTALLATION INSTRUCTIONS diagram (page 9)
Fig. 3
  • This appliance is installed on the wall.
  • Check the position of the screws using the enclosed

template.

  • Follow the enclosed installation instructions for additional

special accessories (e.g. for circulating-air mode).

  • The surfaces of the appliance are sensitive. Avoid damaging

them during installation.

: Important safety information I mportant safety i nformati on

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.

The surfaces of the appliance are easily damaged. Avoid damaging them during installation. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.

Installation instructions

Page 10 of the Constructa CD646850 user manual — Risk of injury! ■ Changes to the electrical or mechanical
Page 10 · cliquer pour agrandir
Page 10

Risk of fire!

In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Fatty deposits in the grease filter may

catch fire. The specified safety clearances must be complied with in order to prevent a build-up of heat. Refer to the information provided for your cooker. If gas and electric hobs are being operated together, the largest specified clearance applies.

  • Adequate incoming air must therefore

Risk of fire! ■ Grease deposits in the grease filter may

always be ensured.

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney).

Risk of injury! ■The appliance may fall down if it has not

been properly fastened in place. All fastening components must be fixed firmly and securely.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

Risk of injury! ■ Changes to the electrical or mechanical

assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.

Page 11 of the Constructa CD646850 user manual — Exhaust duct
Page 11 · cliquer pour agrandir
Page 11

Risk of electric shock!

The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual- current circuit breaker (RCCB) in the appliance's power supply circuit.

  • Components inside the appliance may

have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

Risk of electric shock! ■ It must always be possible to disconnect

Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after- sales service.

the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations.

General information General i nformati on

Exhaust air mode : Risk of death!

Checking the wall

  • The wall must be level, vertical and adequately load-bearing.

Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

  • The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

  • The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks).

  • The max. weight of the extractor hood is 40 kg .

If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.

Electrical connection : Risk of electric shock!

Exhaust duct

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

  • The device achieves its optimum performance by means of a

The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter.

short, straight exhaust air pipe and as large a pipe diameter as possible.

  • As a result of long rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased.

Length of the cableapprox. 1.30 m

This appliance complies with the EC interference suppression regulations. : Risk of electric shock!

  • The pipes or hoses for laying the exhaust air line must

consist of non-combustible material.

Round pipes An inner diameter of 150 mm, but at least 120 mm, is recommended.

It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. The mains plug of the mains power cable must be easily accessible after installation of the appliance. If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual- current circuit breaker (RCCB) in the appliance's power supply circuit.

Flat ducts The inner cross-section must correspond to the diameter of the round pipes.

dia. 150 mm ca. 177 cm2

dia. 120 mm ca. 113 cm2

  • Flat ducts should not have any sharp deflections.
  • Use sealing strips for deviating pipe diameters.
Page 12 of the Constructa CD646850 user manual — Preparing the installation
Page 12 · cliquer pour agrandir
Page 12

Installation I nstal l ati on

Preparing the installation

Installation

1. Screw on the fixing bracket for the flue duct. ¨

Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled.

Constructa CD646850 — Preparing the installation diagram (page 12)
Fig. 4 · Preparing the installation
1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.
2. Use the enclosed template to mark the positions for the screws and the outline of the attachment area.
3. Drill five 8 mm diameter holes to a depth of 80 mm for fastening the appliance and press in the wall plugs flush with the wall.
Constructa CD646850 — Preparing the installation diagram (page 12)
Fig. 5 · Preparing the installation
2. Screw on brackets for the extractor hood hand-tight. Do not firmly tighten the screws. ©
Constructa CD646850 — Preparing the installation diagram (page 12)
Fig. 6 · Preparing the installation
3. Screw in the threaded bolt, leaving it protruding out of the wall by 5–9 mm . ª
Constructa CD646850 — Preparing the installation diagram (page 12)
Fig. 7 · Preparing the installation
Page 13 of the Constructa CD646850 user manual — Attaching the flue duct : Risk of injury!
Page 13 · cliquer pour agrandir
Page 13

Attaching and aligning the appliance

Connecting the pipes

1. First, remove the protective foil from the back of the appliance and, following installation, remove the foil completely.

Exhaust-air pipe Ø 150 mm (recommended size)

2. When attaching the appliance, ensure that it engages firmly with the brackets. «

Attach the exhaust-air pipe directly to the air-pipe connector and seal.

3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬

Exhaust-air pipe Ø 120 mm

1. Attach the reducing connector directly to the air-pipe connector.
Constructa CD646850 — Attaching and aligning the appliance diagram (page 13)
Fig. 8 · Attaching and aligning the appliance
2. Attach the exhaust air pipe to the reducing connector.
3. Seal both joints appropriately.

Attaching the flue duct : Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

1. Separate the flue ducts. To do this, remove the adhesive tape.
2. Remove the protective foil from both flue ducts.
3. Push one flue duct into the other.
  • To prevent scratches, lay paper over the edges of the lower

flue duct to protect the surface.

  • Slots of the inner flue duct point downwards.
4. Place flue ducts on the appliance.
5. Push the inner flue duct upwards and attach it to the fixing brackets on the left and right. ¨
6. Press the flue duct downwards until it engages. ©
4. Firmly tighten the screws for the brackets. When doing so, hold the brackets securely in place. ®
7. Screw the flue duct to the sides of the fixing bracket using two screws. ª
5. Firmly tighten the knurled nuts. ¯
Constructa CD646850 — Attaching the flue duct : Risk of injury! diagram (page 13)
Fig. 9 · Attaching the flue duct : Risk of injury!
Constructa CD646850 — Attaching the flue duct : Risk of injury! diagram (page 13)
Fig. 10 · Attaching the flue duct : Risk of injury!
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD646850

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD646850

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD646850 manuel PDF

56 pages·2.5 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…