FR
Constructa logo
Notice d'utilisation officielle

Constructa CD616251

44 pages·4.3 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD616251
Table des matières 164 sections Ú Table of contents[en] Instructions for installation and use · Instruction manual · : Important safety information · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instructions for installation and usep.1Instruction manualp.1: Important safety informationp.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible ...p.1Children must not play with the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1Danger of suffocation!p.1Packaging material is dangerous to children. Never allow children to play with packaging material.p.1Danger of death!p.1Risk of poisoning from flue gases that are drawn back in.p.1Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.1Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.2In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.2■ Adequate incoming air must therefore always be ensured.p.2■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.2Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Clean the grease filter at least every 2 months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2Risk of injury!p.2■ Components inside the appliance may have sharp edges. Wear protective gloves.p.2■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.2Risk of electric shock!p.3■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.3■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.3■ Penetrating moisture may cause an electric shock. Do not use any highpressure cleaners or steam cleaners.p.3Causes of damagep.3Caution!p.3Environmental protectionp.3Environmental protectionp.3Operating modesp.3Exhaust air modep.3Notep.3Circulating-air modep.3Notep.3Operating the appliancep.4Notep.4Control panelp.4Setting the fanp.4Lightingp.4Cleaning and maintenancep.4: Risk of burns!p.4: Risk of electric shock!p.4: Risk of electric shock!p.4: Risk of injury!p.4Cleaning agentsp.4Cleaning the metal mesh grease filtersp.5: Risk of fire!p.5Notesp.5In the dishwasher:p.5Notep.5By hand:p.5Notep.5Removing metal mesh grease filterp.51. Open the lock and fold down the metal mesh grease filter.p.52. Take the metal mesh grease filter out of the holder.p.5Notesp.53. Clean the metal mesh grease filter.p.5Installing the metal mesh grease filterp.51. Insert the metal mesh grease filter.p.52. Fold the metal mesh grease filter upwards, locking it in place.p.5Trouble shootingp.5: Risk of electric shock!p.5Malfunction tablep.5Replacing bulbsp.6: Risk of electric shock!p.6Replacing halogen bulbsp.6Notep.61. Carefully remove the bulb ring using a suitable tool.p.62. Pull out the bulb and replace it with a bulb of the same type.p.63. Insert the bulb cover.p.64. Insert the mains plug or switch on the fuse again.p.6Replacing filament bulbsp.61. Lift the bulb cover slightly and push towards the outside of the appliance.p.62. Unscrew the bulb and replace it with a bulb of the same type.p.63. Insert the bulb cover.p.64. Insert the mains plug or switch on the fuse again.p.6After-sales servicep.6Accessories for circulating-air modep.6Installation instructionsp.7: Important safety informationp.7Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.7The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.7The width of the extractor hood must correspond at least with the width of the hob.p.7For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.p.7Danger of death!p.7Risk of poisoning from flue gases that are drawn back in.p.7Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.7Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.7In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.7■ Adequate incoming air must therefore always be ensured.p.7■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.7Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.8In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.8Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.8Danger of death!p.8Risk of poisoning from flue gases that are drawn back in. If installing a ventilation system in a room with a heat-producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch.p.8Risk of fire!p.8Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, t...p.8Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.p.8Risk of injury!p.8■ Components inside the appliance may have sharp edges. Wear protective gloves.p.8■ The appliance may fall from the wall if it is not attached properly. All fastening components must be fixed firmly and securely in place.p.8■ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.p.8Risk of electric shock!p.8Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.p.8Danger of suffocation!p.8Packaging material is dangerous to children. Never allow children to play with packaging material.p.8General informationp.8Exhaust air modep.8Notep.8Exhaust ductp.8Notep.8Checking the wallp.9Electrical connectionp.9: Risk of electric shock!p.9Installationp.9Preparing for installationp.9Caution!p.91. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.p.92. Mark the positions for the screws and the contour of the attachment area.p.93. Drill 8 mm Ø holes to a depth of 80 mm and press the wall plugs flush with the wall. ¨p.94. Screw on the fixing bracket for the flue duct. ©p.95. Screw in 2 securing screws with washers to approx. 5 mm. ªp.9Installationp.101. Attaching and aligning the appliance. ¨p.102. Mark the hole for the safety screw. ©p.103. Remove the appliance once more. ªp.10Finishing installation of the appliancep.101. Drill an 8 mm Ø hole to a depth of 80 mm for the safety screw and press the wall plug flush into the wall. ¨p.102. Initially remove the protective foil from the back of the appliance and, following installation, remove the foil completely.p.103. Attach the appliance. ©p.104. Screw in the safety screw - and washer - and tighten all the screws. ªp.10Connecting the appliance to the power supplyp.10Connecting the air extractorp.10Notep.101. Attach the air extractor pipe directly to the air-pipe connector.p.102. Connect to air extractor opening.p.103. Seal the joints appropriately.p.10Connect the power supplyp.101. Plug the mains plug into the earthed socket.p.102. If a fixed connection is required, please follow the instructions in the Electrical Connection section.p.10Attaching the flue ductp.10: Risk of injury!p.101. Separate the flue ducts.p.102. Remove the protective foil from both flue ducts.p.103. Screw the upper flue ducts to the sides of the fixing bracket using two short screws. ¨p.104. Place the lower flue ducts on the appliance and fix in place using two long screws on the bottom of the appliance. ©p.105. Screw the lower flue duct to the sides of the fixing bracket using 2 short screws. ªp.10Notep.10
Page 1 of the Constructa CD616251 user manual — : Important safety information
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents [en] Instructions for installation and use

INSTRUCTION MANUAL 12

INSTALLATION INSTRUCTIONS .............................................18

INSTRUCTION MANUAL

Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards.

Children must not play with the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or a remote control.

Page 2 of the Constructa CD616251 user manual — Risk of injury! ■ Items placed on the appliance may fall
Page 2 · cliquer pour agrandir
Page 2

Risk of fire!

Constructa CD616251 — Risk of fire! diagram (page 2)
Fig. 1 · Risk of fire!
  • Grease deposits in the grease filter may

catch fire. Clean the grease filter at least every 2 months.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

Never operate the appliance without the grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

  • Adequate incoming air must therefore

always be ensured.

Risk of fire! ■ When gas burners are in operation without

  • An incoming/exhaust air wall box alone

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of fire! ■ Operating several gas burners at the

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

Constructa CD616251 — Risk of fire! ■ Operating several gas burners at the diagram (page 2)
Fig. 2 · Risk of fire! ■ Operating several gas burners at the

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

Risk of injury!

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Page 3 of the Constructa CD616251 user manual — Exhaust air mode
Page 3 · cliquer pour agrandir
Page 3

Risk of electric shock!

Causes of damage

  • A defective appliance may cause electric

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Risk of electric shock! ■ Penetrating moisture may cause an

electric shock. Do not use any high- pressure cleaners or steam cleaners.

Environmental protection

Unpack the appliance and dispose of the packaging in an environmentally-responsible manner. Environmental protection

This appliance is labelled in accordance with the European Directive 2002/96/EU concerning used electrical and electronic appliances (WEEE – waste electrical and electronic equipment). The guideline determines the framework for the return and recycling of used appliances as applicable.

Operating modes

This appliance can be used in exhaust-air mode or circulating- air mode.

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Exhaust air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

Note: To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Page 4 of the Constructa CD616251 user manual — Cleaning agents
Page 4 · cliquer pour agrandir
Page 4

Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

0.1 Fan Off/Fan speed 1

2 Fan speed 2

3 Fan speed 3

Control panel Setting the fan

Press button 1, 2 or 3.

Press the 0 button.

Lighting

The lighting can be switched on and off independently of the ventilation.

Press the A button.

Cleaning and maintenance

: Risk of burns!

The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning.

Stainless steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth.

: Risk of electric shock!

Clean stainless steel surfaces in the direction of the grain only.

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.

: Risk of electric shock!

Penetrating moisture may cause an electric shock. Do not use any high-pressure cleaners or steam cleaners.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

: Risk of injury!

Do not use any stainless steel clean- ers.

Components inside the appliance may have sharp edges. Wear protective gloves.

Glass cleaner: Clean with a soft cloth.

Cleaning agents

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Observe the information in the table to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent. Do not use

Operating controls Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth.

  • harsh or abrasive cleaning agents,
  • cleaning agents with a high concentration of alcohol,
  • hard scouring pads or sponges,

Risk of damage to the electronics from penetrating moisture. Never clean operator controls with a wet cloth.

  • high-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.

Follow all instructions and warnings included with the cleaning agents.

Do not use any stainless steel clean- ers.

Show 6 more labels / short text on this page
Explanation · A Light On/Off · Switching on · Switching off · Area Cleaning agents · Aluminium and plastic
Page 5 of the Constructa CD616251 user manual — Malfunction table
Page 5 · cliquer pour agrandir
Page 5

Cleaning the metal mesh grease filters : Risk of fire!

Removing metal mesh grease filter

1. Open the lock and fold down the metal mesh grease filter. While doing this, place the other hand under the metal mesh grease filter.

Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.

2. Take the metal mesh grease filter out of the holder.
  • Grease can accumulate in the bottom of the metal mesh
  • Do not use any aggressive, acidic or alkaline cleaning

grease filter.

agents.

  • Hold the metal mesh grease filter level, otherwise grease
  • When cleaning the metal mesh grease filters, also clean the

will drip out.

holder for the metal mesh grease filters in the appliance using a damp cloth.

Constructa CD616251 — Removing metal mesh grease filter diagram (page 5)
Fig. 3 · Removing metal mesh grease filter
  • The metal mesh grease filters can be cleaned in the

dishwasher or by hand.

In the dishwasher:

3. Clean the metal mesh grease filter.
  • Do not clean heavily soiled metal mesh grease filters together

Installing the metal mesh grease filter

with utensils.

  • Place the metal mesh grease filters loosely in the dishwasher.
1. Insert the metal mesh grease filter. While doing this, place the other hand under the metal mesh grease filter.

The metal mesh grease filters must not be wedged in.

By hand:

2. Fold the metal mesh grease filter upwards, locking it in place.
  • Soak the metal mesh grease filters in a hot soapy solution.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal mesh grease filters to drain.

Trouble shooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Power cut Check whether other kitchen appliances are working

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

The lighting does not work.

The bulbs are faulty.

For information on chang- ing the bulbs, see the "Replacing Bulbs" section.

Page 6 of the Constructa CD616251 user manual — 1 CZ5138X5
Page 6 · cliquer pour agrandir
Page 6

Replacing bulbs : Risk of electric shock!

1. Lift the bulb cover slightly and push towards the outside of the appliance.

When changing the bulbs, the bulb socket contacts are live. Before changing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

2. Unscrew the bulb and replace it with a bulb of the same type.
Constructa CD616251 — Replacing bulbs : Risk of electric shock! diagram (page 6)
Fig. 4 · Replacing bulbs : Risk of electric shock!
3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.
1. Carefully remove the bulb ring using a suitable tool. 2. Pull out the bulb and replace it with a bulb of the same type.
Constructa CD616251 — Replacing bulbs : Risk of electric shock! diagram (page 6)
Fig. 5 · Replacing bulbs : Risk of electric shock!
3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.

Accessories for circulating-air mode

(not included in the delivery)

When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).

Constructa CD616251 — Accessories for circulating-air mode diagram (page 6)
Fig. 6 · Accessories for circulating-air mode

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

E no. FD no.

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Constructa CD616251 — Accessories for circulating-air mode diagram (page 6)
Fig. 7 · Accessories for circulating-air mode

Please find the contact data of all countries in the enclosed customer service list..

Trust the expertise of the manufacturer, and rest assured that the repair will be carried out by trained service technicians using original spare parts for your domestic appliance.

1 CZ5138X5

Show 6 more labels / short text on this page
Replacing filament bulbs · Replacing halogen bulbs · Basic equipment · After-sales serviceO · Throw-away filter · 2 743169
Page 7 of the Constructa CD616251 user manual — : Important safety information
Page 7 · cliquer pour agrandir
Page 7

INSTALLATION INSTRUCTIONS

Constructa CD616251 — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 8
Constructa CD616251 — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 9
  • This appliance is installed on the wall.
  • Follow the enclosed installation instructions for additional

special accessories (e.g. for circulating-air mode).

  • The surfaces of the appliance are sensitive. Avoid damaging

them during installation.

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers. Danger of death! Risk of poisoning from flue gases that are drawn back in. Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.

Constructa CD616251 — : Important safety information diagram (page 7)
Fig. 10 · : Important safety information

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit.

Installation instructions

Page 8 of the Constructa CD616251 user manual — Exhaust duct
Page 8 · cliquer pour agrandir
Page 8

Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.

Risk of injury!

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■The appliance may fall from the wall if it is

not attached properly. All fastening components must be fixed firmly and securely in place.

Risk of injury! ■ The appliance is heavy. To move the

appliance, 2 people are required. Use only suitable tools and equipment.

Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

General information

Exhaust air mode

  • Because of long rough exhaust air pipes, many of which are

pipe bends or have diameters smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased.

  • The pipes or hoses for laying the exhaust duct must consist

of non-combustible material.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

An inner diameter of 150 mm, but at least 120 mm, is recommended.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

The inner cross-section must correspond to the diameter of the round pipes.

Exhaust duct

Ø 150 mm approx. 177 cm2

Ø 120 mm approx. 113 cm2

  • The appliance achieves its optimum performance by means
  • Flat ducts should have no sharp deflections.

of a short, straight exhaust air pipe and as large a pipe diameter as possible.

  • Use sealing strip for deviating pipe diameters.

Round pipes · Flat ducts

Page 9 of the Constructa CD616251 user manual — Preparing for installation
Page 9 · cliquer pour agrandir
Page 9

Checking the wall

Electrical connection : Risk of electric shock!

  • The wall must be level, vertical and adequately load-bearing.
  • The depth of the bore holes must be the same length as the

Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation.

screws. The wall plugs must have a secure grip.

  • The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks).

The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter.

  • The max. weight of the extractor hood is 40 kg .
Length of the cableapprox. 1.30 m

This appliance complies with the EC interference suppression regulations.

This appliance may be connected to a correctly installed earthed socket only.

Attach the earthed socket preferably inside the flue duct.

  • The earthed socket should be connected via its own circuit.
  • If the earthed socket is no longer accessible following

installation of the appliance, a disconnecter must be fitted as for a permanent connection.

If a permanent connection is required, the installation must feature an all-pole disconnecter (circuit breakers, fuses and contactors) with a min. 3 mm contact opening. The permanent connection may be installed by an electrician only.

Installation

Preparing for installation

Constructa CD616251 — Preparing for installation diagram (page 9)
Fig. 11 · Preparing for installation

Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made.

1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.
2. Mark the positions for the screws and the contour of the attachment area.
3. Drill 8 mm Ø holes to a depth of 80 mm and press the wall plugs flush with the wall. ¨
4. Screw on the fixing bracket for the flue duct. ©
5. Screw in 2 securing screws with washers to approx. 5 mm. ª
Page 10 of the Constructa CD616251 user manual — Finishing installation of the appliance
Page 10 · cliquer pour agrandir
Page 10

Installation

Connecting the appliance to the power supply

1. Attaching and aligning the appliance. ¨

Connecting the air extractor

2. Mark the hole for the safety screw. ©
3. Remove the appliance once more. ª
1. Attach the air extractor pipe directly to the air-pipe connector.
Constructa CD616251 — Installation diagram (page 10)
Fig. 12 · Installation
2. Connect to air extractor opening.
3. Seal the joints appropriately.

Connect the power supply

1. Plug the mains plug into the earthed socket.
2. If a fixed connection is required, please follow the instructions in the Electrical Connection section.

Attaching the flue duct : Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

1. Separate the flue ducts. To do this, remove the adhesive tape
2. Remove the protective foil from both flue ducts.
3. Screw the upper flue ducts to the sides of the fixing bracket using two short screws. ¨
4. Place the lower flue ducts on the appliance and fix in place using two long screws on the bottom of the appliance. ©
5. Screw the lower flue duct to the sides of the fixing bracket using 2 short screws. ª

Finishing installation of the appliance

1. Drill an 8 mm Ø hole to a depth of 80 mm for the safety screw and press the wall plug flush into the wall. ¨
Constructa CD616251 — Finishing installation of the appliance diagram (page 10)
Fig. 13 · Finishing installation of the appliance
2. Initially remove the protective foil from the back of the appliance and, following installation, remove the foil completely.
3. Attach the appliance. ©
4. Screw in the safety screw - and washer - and tighten all the screws. ª
Constructa CD616251 — Finishing installation of the appliance diagram (page 10)
Fig. 14 · Finishing installation of the appliance
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD616251

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD616251

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD616251 manuel PDF

44 pages·4.3 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…