FR
Constructa logo
Notice d'utilisation officielle

Constructa CD11391

32 pages·1 MB·Hotte de cuisine·PDF·ENITJA
Constructa CD11391
Table des matières 103 sections Ú Table of contents[en] Instruction manual · Produktinfo · : Important safety information · Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. · … AfficherMasquer
Ú Table of contents[en] Instruction manualp.1Produktinfop.1: Important safety informationp.1Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.p.1The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.p.1This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improp...p.1This appliance is intended for use up to a maximum height of 2000 metres above sea level.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...p.1Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1Danger of suffocation!p.1Packaging material is dangerous to children. Never allow children to play with packaging material.p.1Danger of death!p.1Risk of poisoning from flue gases that are drawn back in.p.1Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.p.1Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air t...p.1In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked ...p.1■ Adequate incoming air must therefore always be ensured.p.1■ An incoming/exhaust air wall box alone will not ensure compliance with the limit.p.1Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that can...p.2In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you.p.2Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.p.2Risk of fire!p.2■ Grease deposits in the grease filter may catch fire.p.2Replace the grease filter at least every two months.p.2Never operate the appliance without the grease filter.p.2■ Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, nonrem...p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.p.2■ Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer t...p.2Risk of burns!p.2The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.p.2Risk of injury!p.2■ Components inside the appliance may have sharp edges. Wear protective gloves.p.2■ Items placed on the appliance may fall down. Do not place any objects on the appliance.p.2Risk of electric shock!p.2■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.2■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.2Causes of damagep.2Caution!p.2Environmental protectionp.3Saving energyp.3Environmentally-friendly disposalp.3Operating modesp.3Exhaust air modep.3Notep.3Circulating-air modep.3Notep.3Operating the appliancep.4Notep.4Notep.4Control panelp.4Setting the fanp.4Notep.4Notep.4Lightingp.4Cleaning and maintenancep.4: Risk of burns!p.4: Risk of electric shock!p.4: Risk of electric shock!p.4: Risk of injury!p.4Cleaning agentsp.4Removing the fleece grease filterp.5: Risk of fire!p.5Notep.51. Press the locks on the left and right of the filter grid.p.52. Swing the filter grid down.p.53. Position the filter grid at an angle and remove it.p.54. Remove the wires and then remove the fleece grease filter.p.55. After removing the fleece grease filter, clean the inside of the appliance.p.56. Clean the filter grid.p.5Fitting the fleece grease filterp.51. Trim the new fleece grease filter to the required size and place it in the filter grid.p.52. Clamp the fleece grease filter in place with the wires.p.53. Insert the filter grid.p.5Notep.5Changing the activated charcoal filter (only in circulating-air mode)p.5Notesp.5Notep.51. Remove the fleece grease filter; see the Removing the fleece grease filter section.p.52. Undo the threaded joint on the activated charcoal filter cover.p.53. Remove the activated charcoal filter.p.54. Insert the activated charcoal filter.p.55. Screw the cover in place.p.56. Fit the fleece grease filter; see the Fitting the fleece grease filter section.p.5Trouble shootingp.6: Risk of electric shock!p.6Malfunction tablep.6Replacing bulbsp.6: Risk of electric shock!p.6: Risk of burns!p.6Replacing halogen bulbs with screw basep.6Notesp.61. Allow the bulb to cool down.p.62. Remove the filter grid.p.63. Unscrew the bulb and replace it with a bulb of the same type.p.64. Fit the filter grid.p.65. Insert the mains plug and switch on the fuse again.p.6After-sales servicep.6Accessoriesp.7
Page 1 of the Constructa CD11391 user manual — : Important safety information
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents [en]Instruction manual

After-sales service 14 Accessories 15

Produktinfo

Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage which is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 metres above sea level. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards. Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.

This appliance is not intended for operation with an external clock timer or a remote control.

Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space.

  • Adequate incoming air must therefore

always be ensured.

  • An incoming/exhaust air wall box alone

will not ensure compliance with the limit.

Page 2 of the Constructa CD11391 user manual — Risk of fire! ■ When gas burners are in operation without
Page 2 · cliquer pour agrandir
Page 2

Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.

  • Operating several gas burners at the

same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.

Risk of burns! The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.

Risk of injury!

In any case, consult your responsible Master Chimney Sweep. He is able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the vapour extractor hood is operated exclusively in the circulating-air mode.

  • Components inside the appliance may

have sharp edges. Wear protective gloves.

Risk of injury! ■ Items placed on the appliance may fall

down. Do not place any objects on the appliance.

Risk of electric shock!

  • A defective appliance may cause electric

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of fire!

  • Grease deposits in the grease filter may

catch fire. Replace the grease filter at least every two months.

Risk of electric shock! ■ Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Never operate the appliance without the grease filter.

Risk of fire! ■ Grease deposits in the grease filter may

catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat- producing appliance for solid fuel (e.g. wood or coal) unless a closed, non- removable cover is available. There must be no flying sparks.

Risk of electric shock! ■ Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

Causes of damage

Risk of fire! ■Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.

Always replace faulty bulbs to prevent the remaining bulbs from overloading.

Risk of fire! ■ When gas burners are in operation without

Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth.

any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.

Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents.

Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Risk of fire!

Page 3 of the Constructa CD11391 user manual — Exhaust air mode
Page 3 · cliquer pour agrandir
Page 3

Environmental protection

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Saving energy

  • During cooking, ensure that there is a sufficient supply of air

so that the extractor hood can work efficiently and with a low level of operating noise.

  • Adjust the fan speed to the intensity of the cooking fumes.

Only use intensive mode where this is required. A lower fan speed means that less energy is consumed.

  • If there are intensive cooking fumes, select a higher fan

speed in good time. If cooking fumes have already spread in the kitchen, the extractor hood must be operated for longer.

  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and, if required, replace the filter at regular intervals in

order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Operating modes

This appliance can be used in exhaust-air mode or circulating- air mode.

Circulating-air mode

The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Exhaust air mode

The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

Note: To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

  • Before conveying the exhaust air into a non-functioning

smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.

  • If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Page 4 of the Constructa CD11391 user manual — Cleaning agents
Page 4 · cliquer pour agrandir
Page 4

Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.

0 Switches off the fan

1 Switches on fan speed 1

2 Switches on fan speed 2

3 Switches on fan speed 3

Setting the fan

Set the slide control to position 1, 2 or 3.

Switching off the appliance

Set the slide control to position 0.

Lighting

The lighting can be switched on and off independently of the ventilation.

0 Switches off the lighting

1 Switches on the lighting

Set the slide control to position 1.

Cleaning and maintenance

: Risk of burns!

The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

Stainless steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth.

: Risk of electric shock!

Clean stainless steel surfaces in the direction of the grain only.

Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.

Special stainless steel cleaning prod- ucts are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.

: Risk of electric shock!

Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear protective gloves.

Do not use any stainless steel cleaners.

Glass cleaner: Clean with a soft cloth.

Cleaning agents

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Observe the information in the table to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent. Do not use

Operating controls Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth.

  • harsh or abrasive cleaning agents,
  • cleaning agents with a high concentration of alcohol,
  • hard scouring pads or sponges,

Risk of damage to the electronics from penetrating moisture. Never clean oper- ator controls with a wet cloth.

  • high-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.

Do not use any stainless steel cleaners.

Follow all instructions and warnings included with the cleaning agents.

Show 7 more labels / short text on this page
2 Fan · Control panel · Switching on · · 1 Lighting · Area Cleaning agents · Aluminium and plas- tic
Page 5 of the Constructa CD11391 user manual — Changing the activated charcoal filter (only in circulating-air mode)
Page 5 · cliquer pour agrandir
Page 5

Removing the fleece grease filter : Risk of fire!

Fitting the fleece grease filter

1. Trim the new fleece grease filter to the required size and place it in the filter grid.

Grease deposits in the grease filter may catch fire. Replace the grease filter at least every two months. Never operate the appliance without the grease filter.

2. Clamp the fleece grease filter in place with the wires.
3. Insert the filter grid.

Changing the activated charcoal filter (only in circulating-air mode)

1. Press the locks on the left and right of the filter grid.
Constructa CD11391 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 1 · Changing the activated charcoal filter (only in circ…

In order to guarantee efficient odour filtration, the filter must be serviced regularly.

The activated charcoal filters must be replaced at least every 4 months.

  • The activated charcoal filters are not included in the delivery.

The activated charcoal filters can be obtained from specialist retailers, from our after-sales service or from the Online Shop.

  • The activated charcoal filters cannot be cleaned or

reactivated.

2. Swing the filter grid down.
Constructa CD11391 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 2 · Changing the activated charcoal filter (only in circ…
1. Remove the fleece grease filter; see the Removing the fleece grease filter section.
2. Undo the threaded joint on the activated charcoal filter cover.
Constructa CD11391 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 3 · Changing the activated charcoal filter (only in circ…
3. Position the filter grid at an angle and remove it.
Constructa CD11391 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 4 · Changing the activated charcoal filter (only in circ…
3. Remove the activated charcoal filter.
4. Insert the activated charcoal filter.
5. Screw the cover in place.
6. Fit the fleece grease filter; see the Fitting the fleece grease filter section.
4. Remove the wires and then remove the fleece grease filter.
Constructa CD11391 — Changing the activated charcoal filter (only in circulating-air mode) diagram (page 5)
Fig. 5 · Changing the activated charcoal filter (only in circ…
5. After removing the fleece grease filter, clean the inside of the appliance.
6. Clean the filter grid.
Page 6 of the Constructa CD11391 user manual — After-sales service
Page 6 · cliquer pour agrandir
Page 6

Trouble shooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. : Risk of electric shock!

Replacing bulbs : Risk of electric shock!

When changing the bulbs, the bulb socket contacts are live. Before changing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

: Risk of burns!

Halogen bulbs become very hot when switched on. There is still a risk of burning for some time after they have been switched off. Allow the halogen bulbs to cool down before replacing them.

Malfunction table

Problem Possible cause Solution

The appliance does not work

The plug is not plugged in.

Connect the appliance to the electricity supply

Power cut Check whether other kitchen appliances are working

Replacing halogen bulbs with screw base

Faulty fuse Check in the fuse box to make sure that the fuse for the appliance is OK

  • To replace the bulbs, do not remove the plastic cover. The

bulbs can be accessed from inside by removing the filter grid.

The lighting does not work.

The bulbs are faulty.

For information on chang- ing the bulbs, see the "Replacing Bulbs" section.

  • When inserting halogen bulbs, do not touch the glass bulb.

Use a clean cloth to insert the halogen bulbs.

1. Allow the bulb to cool down.
2. Remove the filter grid.
3. Unscrew the bulb and replace it with a bulb of the same type.
4. Fit the filter grid.
5. Insert the mains plug and switch on the fuse again.

Replace the bulb with one of the same type:

Voltage230 V
PowerMax. 28 W
ThreadE14

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician.

When calling us, please quote the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the filter grid to gain access).

You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.

E no. FD no.

Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period.

Please find the contact data of all countries in the enclosed customer service list.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

· After-sales serviceO

Page 7 of the Constructa CD11391 user manual — CZ5201X0
Page 7 · cliquer pour agrandir
Page 7

Accessories

(not included in the scope of delivery)

CZ5101X0

Constructa CD11391 — CZ5101X0 diagram (page 7)
Fig. 6

CZ5201X0

Constructa CD11391 — CZ5201X0 diagram (page 7)
Fig. 7

Activated charcoal filter · Fleece grease filter ·

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CD11391

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CD11391

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CD11391 manuel PDF

32 pages·1 MB·Hotte de cuisine·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…