Manuel d'utilisation / d'entretien du produit 315-00109 du fabricant Viper
Aller à la page of 25
315-00109 07/07 Rev A Owner’s Manual SERIAL TAG IS LOCATED ON THE FRAME Model Name: Viper Date of Purchase: Serial Number: Customer Service 1.800.750.
2 Important Safety Information 3-4 P arts Identifier 5-6 Assembly 7-12 Console Instructions 13-17 Monitoring Y our Heart R ate 18 W arm-Up Ex ercises 19 Gener al Instructions 20 Moving Instructions 21.
3 WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 Thank you for purchasing the Ironman Fitness Viper Recumbent Bike ! The quality product you hav e chosen was designed to meet your needs for cardiov ascular exercise. Before you start, please read the Owner’s Manual and become familiar with the operation of your new unit.
Parts Identifier 5 Seat Slide Adjustment Handle Main Frame Front Rear Handle Bar Console Front Stabilizer Rear Stabilizer Main Support T ube Back Rest Seat Pad INSTRUCTIONS FOR ASSEMBLY: Unpack the box in a clear area. Check to make sure all components are present and in good condition.
6 Parts Identifier INSTRUCTIONS FOR ASSEMBLY: Unpack the box in a clear area. Check to make sure all components are present and in good condition. Do not dispose of the packing material until the assembly is completed. T ools have been provided for you to use when assembling this product.
7 Getting Started - The Ironman Fitness Viper R ecumbent Bike will require some assembly . Unpack the box in a clear area. R emove packing material. Do not dispose of packing material until assembly is complete and unit is working properly . Place the unit on a clean level surface for assembly .
8 Assembly Figure 3 Step 1: Connect hand pulse sensor wire-rear (A24) to the hand pulse sensor wire-middle (A23). Connect the power cord (A31) to power cord (A32). Step 2: Locate the front (A1) and rear (A2) main frames. Connect both front and rear frames.
9 Assembly N10 A9 Figure 5 Step 1: Slide the seat adjustment handlebar (A11) into the main frame and secure using stop- ping screw (N10). Step 2: Connect sensor wire (A32) to sensor wire (J1) and side handlebar (J-R) onto sliding track (A9). Secure using three bolts (N7).
10 Assembly Figure 7 Step 1: Locate backrest (H) and secure onto the backrest tube (A10) using four screws (N6). Step 2: Locate plastic bottle holder (K1) and secure to the middle of the main support tube (D) using two screws (K3). Place water bottle (K2) into water bottle holder (K1).
F Figure 9 Step 1: Locate console (F), and connect sensor wires (E5, A25, A26, E6, E7) to the wires coming from the console. Step 2: Gently push all of the wires into the con- sole tube. Slide console onto the console tube. Secure using two screws (F1).
12 Assembly CONGRATULATIONS! You have completed assembly of your Viper Recumbent Bike..
13 Console Instructions T ake a few moments to review the console layout. Below is an overview of the console and their different functions. CONSOLE BUTTONS MODE: This button is used as an enter key , and will allow user to move to the next setting that can be changed.
14 Console Instructions WEIGHT and AGE. During your workout, these buttons are used to increase/decrease the resistance level from 1 to 16. Press and hold for two seconds to rapidly increase/decrease val- ues.
15 Console Instructions RECOVERY: After your workout, keep holding on hand grips and press “RECOVERY” button. All function dis- play will stop except “TIME” starts counting down from 01:00 to 00:00. Screen will display your heart r ate recovery status r ating between F1-F6.
16 Console Instructions Time will flash in the display . Use the +/- buttons to set desired time. Press MODE to con- firm selection. R epeat steps for distance, pulse, resistance, and calories. Press ST ART/ST OP to begin exercising at any time. Y ou can change the tension level at any time during your workout session by pressing the +/- buttons.
Console Instructions 17 If TRG is selected, use the +/- buttons until desired target heart rate is selected. Press MODE button to confirm selection. Time will flash in the display . Use the +/- buttons to set desired time. Press MODE to confirm selection.
18 Monitoring Your Heart Rate Monitoring Your Heart Rate T o obtain the greatest cardiov ascular benefits from your exercise workout, it is important to work within your target heart r ate zone. The American Heart Association (AHA) defines this target as 60%-75% percent of your maximum heart r ate.
1 9 TOE TOUCH STRETCH Stand, bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees, and back.
General Instructions 20 How To Use The Seat Adjustment Bar To Find A Proper Seat Position Push the seat slide adjustment handle forward, then slide the seat up and down until desired position is found. When desired position is found, pull the adjustment handle back into the upward position.
Moving Instructions Caution! To reduce the possibility of injury while lifting, bend your legs and keep your back straight. As you lean the unit, lift using your legs, not your back.
Ref # Parts # DESCRIPTION Qty Ref # Parts # Descritption Qty A1 323-00586 FRONT MAIN FRAME 1 A29 302-01538 SCREW, HEXAGON 8X25MM 2 A2 323-00592 REAR MAIN FRAME 1 A30 319-00386 COVER, FOR CRANK 2 A3 31.
5 N 3 - 2 E 3 - 2 E 3 N 3 N 1 5 A 5 4 A 1 N 3 x 7 N 8 4 A 7 4 A 7 4 A 1 N 8 4 A 8 4 A 7 x 4 4 A 6 4 A 9 4 A 9 4 A 8 N 2 N 3 N 4 N 2 N 3 N 6 4 A 2 N 3 N 2 5 A 8 4 A 6 4 A 7 N 0 5 A 6 4 A 6 4 A 6 4 A 5 .
Res ide ntia l a nd Pers onal Us e L imit ed W arr anty PLE ASE REA D THESE WARRAN TY TERMS AND CONDI TION S FULLY AND CAREFU LLY BEF ORE USI NG YOUR IRONMAN FITNES S EQU IPMEN T. BY USIN G T HE EQU IPMEN T, Y OU AR E CO NSENT ING T O BE BOUND BY T HE FO LLOW ING T ERMS AND CONDI TION S.
Customer Service 1.800.750.IRON 1.800.750.4766 Ironman Fitness 4009 Distribution Drive Suite 250 Garland, TX 75041 www.ironmanfitness.com Ironman, Ironman Triathalon and M-dot are registered trademarks of the World Triathlon Corporation. This product is licensed by the Ironman Triathlon.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Viper Viper 315-00109 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Viper Viper 315-00109 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Viper Viper 315-00109, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Viper Viper 315-00109 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Viper Viper 315-00109, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Viper Viper 315-00109.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Viper Viper 315-00109. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Viper Viper 315-00109 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
