Manuel d'utilisation / d'entretien du produit 536.886331 du fabricant Sears
Aller à la page of 28
OWNER'S MANUAL MODEL NO. 536.886331 HOW TO ORDER REPAIR PARTS CRAFTSMAN® 10 HORSEPOWER 29" DUAL STAGE 120V. ELECTRIC START SNOW THROWER WHEN ORDERING REPAIR PARTS, ALWAYS Each SNOW THROWER has its own MODEL NUMBER found on the engine mount frame.
& SAFETY RULES CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND A PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING WHEN SETTING-UP TRANSPORTING, ADJUSTING OR MAKING REPAIRS. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY.
SAFETY RULES • Never operate the snow thrower near glass enclosures, automobiles, window wells drop- offs, and the like without proper adjustment of the snow discharge angle. Keep children and pets away. • Never operate the snow thrower at high transport speeds on slippery surfaces.
CONGRATULATIONS on your purchase of a Sears _rattsman Snow Thrower. It has been designed, engi- neered a_d manufactured to give you the best poss;ble dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/Department.
TABLE OF CONTENTS SAFETY RULES ........................................ 2,3 PRODUCT SPECIFICATIONS ...................... 4 CUSTOMER RESPONSIBILITIES ..... 4,17-19 WARRANTY .................................................. 4 TABLE OF CONTENTS .......
CONTENTS OF HARDWARE PACK CONTENTS OF PARTS BAG "2- Spare Shear Bolts 1- 3/8 - 16 x 2.00 In. Hex Head Bolt (1/4_0 x 1-3/4 In.) *2- Spare Spacers 2- 3/8 In. Flat washers © 1- 3/8 In. Lock washer 1 - Knob With Threads (not shown actual size) "2- Spare 1/4 - 20 Locknuts 1- 3/8 In.
ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY 1 - Knife (to cut carton and plastic ties/ 2 - 1/2 inch wrenches (or adjustable wrenches) 2 - 9/16 inch wrenches (or adjustable wrenches} 2- 3/4 inch wrenches (or .
ASSEMBLY • Assemble the snow chute. • Roll snow thrower off the skid by pulling on the handle. • Properly dispose of discarded packaging. HOW TO SET UP YOUR SNOW THROWER Your snow thrower is equipped with height adjust skids (See FIG. 2) on the outside of the auger housing.
ASSEMBLY Bend the ends of the cotter pin around the rod and reinstall the plastic cap. Tighten the eye bolt installed earlier, keeping eye in line with the rod while tightening the inside securely Rotate the chute crank fully clockwise and tully cou nter- clockwise.
ASSEMBLY TO INSTALL THE SHIFTER LEVER Stand the snow thrower up on the front of the auger housing, as shown in FIG.8A. Note: Place a piece of cardboard under front to prevent paint damage to auger housing. Cut the plastic tie which holds the shifter lever assembly to the shift bracket (FIG.
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
OPERATION The operation of any snow thrower can result in foreign objects being thrown into the eyes, which ca. result in severe eye damage. Always wear safety glasses or eye shieJds while operating the _now thrower.
OPERATION TO USE WHEEL LOCKOUT PIN • The left hand wheel is secured to the axle with a klick pin (See FIG. 5A). This unit was shipped with this klick pin in the locked (through wheel hole) position.
OPERATION CAUTION: GASOLINE IS FLAMMABLE AND CAUTION MUST BE USED WHEN HANDLING OR STORING IT. DO NOT FILL FUEL TANK WHILE SNOW THROWER IS RUNNING, WHEN IT IS HOT, OR WHEN SNOW THROWER IS IN AN ENCLOSED AREA. KEEP AWAY FROM OPEN FLAME OR AN ELEC- TRICAL SPARK AND DO NOT SMOKE WHILE FILLING THE FUEL TANK.
OPERATION _1_ CAUTION:THIS STARTER IS EQUIPPED WITH ATHREE-WIRE POWER CORD AND PLUG AND IS DESIGNED TO OPERATE ON 120 VOLT AC HOUSEHOLD CUR- RENT. IT MUST BE PROPERLY GROUNDED AT ALL TIMES TO AVOID THE POSSIBILITY OF EL EC- TRICAL SHOCK, WHICH MAY BE INJURIOUS TO OPERATOR.
OPERATION SNOW THROWING TIPS CHOKE CONTROL IGNITION RECOIL KEY STARTER THRO'rrLE CONTROL FIG. 8 CAUTION: DO NOT ATTEMPT TO RE- MOVE ANY ITEM THAT MAY BECOME LODGED IN AUGER WITHOUT TAKING THE FOLLOWING PRECAUTIONS: • RELEASE AUGER DRIVE AND TRACTION DRIVE LEVERS.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill In dates as you com- plete regular service SCHEDULE After Before [ Every Every First 2 Each As 10 25 Each Before hours Use Needed Hours Hours Season Stor.
CUSTOMER RESPONSIBILITIES SNOW THROWER LUBRICATION - EVERY TEN HOURS Auger Shaft - Using a hand grease gun, lubricate the auger shaft zerk fittings (See A, FIG, 2) every ten (10) operating hours.
CUSTOMER RESPONSIBILITIES LUBRICATION • Hex Shaft and Gears - Hex shait and gears require no lubrication. All bearings and bushings =t? lifetime lubricated and require no maintenance (See FIG. 3). NOTE: Any greasing or oiling of the above components can cause contamination of the friction wheel.
SERVICE AND ADJUSTMENTS I CAUTION: ALWAYS DISCONNECT THE I SPARK PLUG WIRE AND TIE BACK AWAY FROM THE PLUG BEFORE MAK- ING ANY ADJUSTMENTS OR REPAIRS. TO ADJUST SKID HEIGHT This snow thrower is equipped with two height adjustment skids, located on the outside of the auger housing (See FIG.
SERVICE AND ADJUSTMENTS TO ADJUST THE CLUTCH CONTROL CABLES Periodic adjustment of the cables may be required due to normal stretch and wear on the belts.
SERVICE AND ADJUSTMENTS TO REPLACE BELTS The drive belts on this snow thrower are of special construction and should be replaced with original equip merit belts available from your nearest Sears Store or Service Center. You will need the assistance of a second person while replacing the belts.
SERVICE AND ADJUSTMENTS TRACTION DRIVE BELT TO ADJUST THE FRICTION WHEEL It your snow thrower will not move forward, ':heck the tractiondrive belt for wear. It the traction drive belt needs to be replaced, proceed as follows: • Disconnect the spark plug wire.
SERVICE AND ADJUSTMENTS TO REPLACE FRICTION WHEEL if the snow thrower will not move forward, and the friction wheel is worn or damaged, you need to replace it. as follows: (First allow the engine to cool). _b CAUTION: DRAIN GASOLINE OUTDOORS AWAY FROM FIRE OR FLAMF / • Drain the gasoline from the fuel tank.
SERVICE AND ADJUSTMENTS TO REPLACE AUGER SHEAR BOLT The augers are secured to the auger shaft with special bolts (See FIG. 16) that are designed to break (to protect the mechlne) if an object becomes lodged in the auger housing. Use of a harder bolt will destroy the protection provided by the shear bolt.
SERVICE AND ADJUSTMENTS TO ADJUST OR REPLACE THE SPARK PLUG If you have difficulty starting your snow thrower, you may need to adjust or replace the spark plug. Follow the instructions below. Replace the spark plug if electrodes are pitted or burned or if the porcelain is cracked.
- STORAGE CAUTION: NEVER STORE YOUR SNOW THROWER INDOORS OR IN AN EN- CLOSED, POORLY VENTILATED AREA IF GASOLINE REMAINS IN THE TANK. FUMES MAY REACH AN OPEN FLAME, SPARK OR PI- LOT LIGHT FROM A FURNACE, WATER HEATER, CLOTHES DRYER, CIGARETTE, ETC.
TROUBLE SHOOTING POINTS TROUBLE Difficult starting Engine runs en'stlcelly Engine stalls Engine runs erratically; Loss of power Excessive vibration Unit falls to propel itself Unit fails to disch.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sears 536.886331 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sears 536.886331 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sears 536.886331, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sears 536.886331 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sears 536.886331, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sears 536.886331.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sears 536.886331. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sears 536.886331 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
