FR
PSC logo
Notice d'utilisation officielle

PSC 2200VS

48 pages·2.7 MB·Scanner·PDF·ENNLJA
PSC 2200VS
Table des matières 13 sections Quick Reference Guide · Introduction · Connection · Operation · … AfficherMasquer
Page 1 of the PSC 2200VS user manual
Page 1 · cliquer pour agrandir
Page 1
PSC 2200VS diagram (page 1)
Fig. 1
Page 2 of the PSC 2200VS user manual — Disclaimer
Page 2 · cliquer pour agrandir
Page 2

PSC Inc 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140

An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of PSC Inc. or its wholly owned subsidiaries ("PSC"). Owners of PSC products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business pur- poses. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contacting your PSC rep- resentative. Electronic versions may either be downloadable from the PSC website (www.psc.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other PSC publications, please let us know via the “Contact PSC” page.

Disclaimer

PSC has taken reasonable measures to provide information in this manual that is complete and accurate, however, PSC reserves the right to change any specification at any time without prior notice.

PSC is a registered trademark of PSC Inc. The PSC logo is a trademark of PSC. All other trademarks and trade names referred to herein are property of their respective owners.

Magellan, FirstStrike and SurroundScan are registered trademarks of PSC Inc. All-Weighs, OmegaTek, Produce Rail, Productiv-

ity Index Reporting, SmartSentry and Any-Weighs are all trademarks of PSC Inc.

  • This product may be covered by one or more of the following patents: 4603262
  • 4639606
  • 4652750
  • 4672215
  • 4699447
  • 4709369
  • 4749879 4786798
  • 4792666
  • 4794240
  • 4798943
  • 4799164
  • 4820911
  • 4845349
  • 4861972
  • 4861973
  • 4866257
  • 4868836
  • 4879456
  • 4939355
  • 4939356
  • 4943127
  • 4963719
  • 4971176
  • 4971177
  • 4991692
  • 5001406
  • 5015831
  • 5019697
  • 5019698
  • 5086879
  • 5115120
  • 5144118
  • 5146463
  • 5179270
  • 5198649
  • 5200597
  • 5202784
  • 5208449
  • 5210397
  • 5212371
  • 5212372
  • 5214270
  • 5229590
  • 5231293
  • 5232185
  • 5233169
  • 5235168
  • 5237161
  • 5237162
  • 5239165
  • 5247161
  • 5256864
  • 5258604
  • 5258699
  • 5260554
  • 5274219
  • 5296689
  • 5298728
  • 5311000
  • 5327451
  • 5329103
  • 5330370
  • 5347113
  • 5347121
  • 5371361
  • 5382783
  • 5386105
  • 5389917
  • 5410108
  • 5420410
  • 5422472
  • 5426507
  • 5438187
  • 5440110
  • 5440111
  • 5446271
  • 5446749
  • 5448050
  • 5463211
  • 5475206
  • 5475207
  • 5479011
  • 5481098
  • 5491328
  • 5493108
  • 5504350
  • 5508505
  • 5512740
  • 5541397
  • 5552593
  • 5557095
  • 5563402
  • 5565668
  • 5576531
  • 5581707
  • 5594231
  • 5594441
  • 5598070
  • 5602376
  • 5608201
  • 5608399
  • 5612529
  • 5629510
  • 5635699
  • 5641958
  • 5646391
  • 5661435
  • 5664231
  • 5666045
  • 5671374
  • 5675138
  • 5682028
  • 5686716
  • 5696370
  • 5703347
  • 5705802
  • 5714750
  • 5717194
  • 5723852
  • 5750976
  • 5767502
  • 5770847
  • 5786581
  • 5786585
  • 5787103
  • 5789732
  • 5796222
  • 5804809
  • 5814803
  • 5814804
  • 5821721
  • 5822343
  • 5825009
  • 5834708
  • 5834750
  • 5837983
  • 5837988
  • 5852286
  • 5864129
  • 5869827
  • 5874722
  • 5883370
  • 5905249
  • 5907147
  • 5923023
  • 5925868
  • 5929421
  • 5945670
  • 5959284
  • 5962838
  • 5979769
  • 6000619
  • 6006991
  • 6012639
  • 6016135
  • 6024284
  • 6041374
  • 6042012
  • 6045044
  • 6047889
  • 6047894
  • 6056198
  • 6065676
  • 6069696
  • 6073849
  • 6073851
  • 6094288
  • 6112993
  • 6129279
  • 6129282
  • 6134039
  • 6142376
  • 6152368
  • 6152372
  • 6155488
  • 6166375
  • 6169614
  • 6173894
  • 6176429
  • 6188500
  • 6189784
  • 6213397
  • 6223986
  • 6230975
  • 6230976
  • 6237852
  • 6244510
  • 6259545
  • 6260763
  • 6266175
  • 6273336
  • 6276605
  • 6279829
  • 6290134
  • 6290135
  • 6293467
  • 6303927
  • 6311895
  • 6318634
  • 6328216
  • 6332576
  • 6332577
  • 6343741
  • 6454168
  • 6478224
  • 6,568,598
  • 6,578,765
  • 6705527
  • AU703547
  • D312631
  • D313590
  • D320011
  • D320012
  • D323492
  • D330707
  • D330708
  • D349109
  • D350127
  • D350735
  • D351149
  • D351150
  • D352936
  • D352937
  • D352938
  • D352939
  • D358588
  • D361565
  • D372234
  • D374630
  • D374869
  • D375493
  • D376357
  • D377345
  • D377346
  • D377347
  • D377348
  • D388075
  • D446524
  • EP0256296
  • EP0260155
  • EP0260156
  • EP0295936
  • EP0325469
  • EP0349770
  • EP0368254
  • EP0442215
  • EP0498366
  • EP0531645
  • EP0663643
  • EP0698251
  • GB2252333
  • GB2284086
  • GB2301691
  • GB2304954
  • GB2307093
  • GB2308267
  • GB2308678
  • GB2319103
  • GB2333163
  • GB2343079
  • GB2344486
  • GB2345568
  • GB2354340
  • ISR107546
  • ISR118507
  • ISR118508
  • JP1962823
  • JP1971216
  • JP2513442
  • JP2732459
  • JP2829331
  • JP2953593
  • JP2964278
  • MEX185552
  • MEX187245
  • RE37166
  • Other Patents Pending
Page 3 of the PSC 2200VS user manual — Quick Reference Guide i
Page 3 · cliquer pour agrandir
Page 3

PSC INC. MAGELLAN ® END USER LICENSE AGREEMENT

Notice to End User: The PSC Product you have acquired contains embedded Software, which is integral to the product’s operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the PSC Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, PSC is not willing to license the Software to you, you may not use the PSC Product or the Software, and you must contact the party from whom you acquired the PSC Product for instructions.

This End User Software License Agreement (“Agreement”) is a legally binding agreement governing the licensing of the Software and Documentation by PSC Inc. and its wholly owned subsidiaries and affiliates (“PSC”) to the entity or person who has purchased or otherwise acquired a PSC Product (“End User”). For purposes of this Agreement, any software that is associated with a separate end-user license agreement is licensed to you under the terms of that license agreement. PSC and End User hereby agree as follows:

1. Definitions.

1.1 "Documentation" means materials such as user’s guides, program reference guides, quick reference guides, manuals, or similar materials associated with or related to the PSC Product, whether in printed, “online”, or other form. 1.2 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related internal design, system design, data base design, algorithms, technology, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the circumstances, should recog- nize as confidential. Proprietary Information does not include any information that the receiving party can establish was (1) in the public domain, (2) already in the receiving party’s possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's pro- prietary rights, or (4) independently developed without access to Proprietary Information.

1.3 “PSC Product” means the PSC Magellan® 9500 series, Magellan® 8500 series, Magellan® 8200 series, Magellan® 8100 series, and/or Magellan SL® series scanner and/or scanner/scale product, including all embedded Software in and all Documentation related to such product, which has been pur- chased or otherwise acquired by End User, whether obtained directly or indirectly from PSC. 1.4 "Software" means any software or computer programs of PSC or its third party licensors in machine readable form which is embedded in the PSC Product, whether obtained directly or indirectly from PSC, including any replacement, update, upgrade, enhancement or modification.

2. Scope Of License Granted.

2.1 PSC grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solely on the PSC Product in which it is embedded (“designated PSC Product”), in machine-readable form only, solely for End User's internal business purposes. This Agreement does not convey own- ership of the Software to End User. Title to the Software shall be and remain with PSC or the third party from whom PSC has obtained a licensed right. As used in this Agreement, the term “purchase” or its equivalents when applied to the Software shall mean “acquire under license.” End User is not entitled to receipt or use of the source code to any Software. 2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for pur- poses other than as expressly provided in this Agreement, without PSC’s prior written consent.

3. Transfers, Support.

3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of the Software on other than the desig- nated PSC Product will be a material breach of this Agreement. However, PSC may elect not to terminate this Agreement or the granted licenses, but instead may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall pay PSC the applicable list price for such licenses as of the date of such breach. 3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the PSC Product to any third party unless such third party agrees with PSC in writing to be bound by the terms and conditions of this Agreement. Any such transfer of the PSC Product absent such agreement shall be null and void. 3.3 End User may obtain support for Software from PSC at PSC’s standard support fees and under PSC’s standard support terms and conditions in effect at the time the support is requested.

4. Intellectual Property.

End User acknowledges that the Software constitutes valuable trade secrets of PSC or PSC’s third party licensors and that the Software is protected by intel- lectual property laws and treaties. The license set forth in this Agreement does not transfer to End User any ownership of PSC’s or its third party licensors' copyrights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right to commence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on the PSC Product.

5. Proprietary Information.

5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret property of PSC and PSC’s third party licensors and End User acquires no right or interest in any Proprietary Information. 5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of PSC or its third party licensors to any person other than End User’s authorized employees or agents who are under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with use of the PSC Product exclusively for End User’s internal business purposes. End User shall take steps to protect the Proprietary Information no less securely than if it were End User's own intellectual property. 5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement.

6. Limited Warranty.

6.1 PSC warrants that, under normal use and operation, the PSC Product will conform substantially to the applicable Documentation for the period speci- fied in the Documentation. During this period, for all reproducible nonconformities for which PSC has been given written notice, PSC will use commer- cially reasonable efforts to remedy nonconformities verified by PSC. End User agrees to supply PSC with all reasonably requested information and assistance necessary to help PSC in remedying such nonconformities. For all defects reported to PSC within the warranty period, PSC’s liability is lim- ited to providing End User with one copy of corrections or responding to End User's problem reports according to PSC's standard assistance practices. PSC does not warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that PSC's remedial efforts will correct any nonconformance. This limited warranty does not cover any product that have been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the prod-

Quick Reference Guide i

Page 4 of the PSC 2200VS user manual — - END -
Page 4 · cliquer pour agrandir
Page 4

uct, uses the product in any manner other than as established in the Documentation, or if End User breaches any of the provisions of this Agreement. 6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE PSC PRODUCT IS PROVIDED “AS IS” AND PSC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRAN- TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

7. Infringement.

7.1 PSC will defend End User against any claim in a lawsuit that the PSC Product furnished hereunder infringe a United States patent or copyright of a third party and PSC will pay any damages finally awarded against End User by a court of competent jurisdiction that are attributable to such claim or will pay End User’s part of any settlement that is attributable to such claim, provided, that 1) End User notifies PSC promptly in writing of the claim, 2) PSC controls the defense or settlement of the claim, and 3) End User cooperates fully with PSC in such defense or settlement. All notices of a claim should be sent to PSC Inc., Legal Department, 111 SW Fifth Ave. Suite 4100, Portland, OR 97204-3644. 7.2 In the defense or settlement of any such claim, PSC may, at its option, 1) procure for End User the right to continue using the PSC Product, 2) modify the PSC Product so that it becomes non-infringing, 3) replace the PSC Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to return the PSC Product and receive a refund of the purchase price paid, less a reasonable allowance for use. 7.3 PSC shall have no liability to End User for claims of infringement based upon 1) the use of any PSC Product in combination with any product which PSC has not either furnished or authorized for use with such PSC Product 2) the use of any PSC Product designed, manufactured, or modified to the specifications of End User, or 3) End User’s modification of the PSC Product without written authorization from PSC. 7.4 THE FOREGOING STATES PSC’S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTEL- LECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.

8. Limitation Of Liability.

EXCEPT AS PROVIDED IN SECTION 7, PSC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL PSC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE PSC PRODUCT. UNDER NO CIRCUMSTANCES SHALL PSC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMI- LAR DAMAGES, EVEN IF PSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

9. Government Restricted Rights; International Use.

9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), whichever is applicable. 9.2 If End User is using the PSC Product outside of the United States, End User must comply with the applicable local laws of the country in which the PSC Product is used, with U.S. export control laws, and with the English language version of this Agreement. The provisions of the “United Nations Convention on International Sale of Goods” shall not apply to this Agreement.

10. Termination.

10.1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provision of this Agreement. 10.2 Upon termination of this Agreement, End User immediately shall cease using any non-embedded software and shall return to PSC or destroy all non- embedded software covered by this Agreement, and shall furnish PSC with a certificate of compliance with this provision signed by an officer or autho- rized representative of End User. For embedded software, End User agrees to sign a waiver prepared by PSC concerning further use of the embed- ded Software. End User’s resumed or continued use of the embedded Software after termination shall constitute End User’s agreement to be bound by the terms and conditions of this Agreement for such use.

11. General Provisions.

11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and super- sedes all prior or contemporaneous agreements, written or oral, between the parties concerning the licensing of the Software. This Agreement may not be changed, amended, or modified except by written document signed by PSC. 11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective when received, with evidence of receipt. Notices to PSC shall be sent to the attention of Contract Administration, PSC Scanning Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by PSC in writing. 11.3 Waiver. A party’s failure to enforce any of the terms and conditions of this Agreement shall not prevent the party’s later enforcement of such terms and conditions. 11.4 Governing Law; Venue:This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Mult- nomah or Lane counties shall have exclusive jurisdiction over all matters regarding this Agreement, except that PSC shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in which End User resides, or in which any of End User's assets are located.

11.5 Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this Agreement, the prevailing party shall be entitled to reason- able attorneys’ fees, both at trial and on appeal.

- END -

ii Magellan ® 2200VS/2200VS Ω

Page 6 of the PSC 2200VS user manual — iv Magellan ® 2200VS/2200VS Ω
Page 6 · cliquer pour agrandir
Page 6

iv Magellan ® 2200VS/2200VS Ω

Page 7 of the PSC 2200VS user manual — Figure 1. Connections
Page 7 · cliquer pour agrandir
Page 7

Introduction

This guide offers a summary of basic scanner operation for first time users. Install- ers, system managers and other technical personnel can find installation, program- ming and further advanced information in the Product Reference Guide. Up-to- date revisions of publications can be viewed, printed and downloaded from the PSC website listed on the back cover of this manual. Printed manuals can also be ordered from your dealer/distributor.

Connection

For your convenience, Figure 1 shows scanner connections and their functions.

Figure 1. Connections

EAS Opening Scanner Host Aux. Port Power EAS ConnectionPOS TERMINALAUXILIARY PORTPOWER · Electronic Article Surveillance Connection· Label Data · Application Download (where appropriate)· Test Port · On Screen Programming (OSP) · Application Download · RS-232 Handheld Scanner Input · Auxiliary RS-232 Label Data Output· DC Brick Input Connection to this port is OptionalConnection to this port is Optional
Page 8 of the PSC 2200VS user manual — Figure 2. Sweep and Presentation Scanning Technique
Page 8 · cliquer pour agrandir
Page 8

Operation

Scanning Items

Item bar codes are scanned by either...

  • sliding or pushing items through the scan volume in a right-to-left or left-toright motion (see Figure 2 a). This is known as “Sweep” scanning, and is the best choice for high throughput superand hypermarket installations where it is necessary to minimize the need to grip or lift items.
  • moving the bar code directly toward the scan window to be read (see Figure 2 b). This “Presentation” technique is most often used in low throughput variety, convenience market and pharmacy applications where useable countertop space is at a premium and “Sweep” scanning is not possible.

With FirstStrikeTM decoding software, the scanner can read most hard-to-read codes quickly and without excess orientation.

Figure 2. Sweep and Presentation Scanning Technique

Scan Volume Items are pushed or slid past scanner

Scanner

Item Bar Code

Scanner a

Item Bar Code

Scan Volume

a Sweep Technique Presentation Technique b

Page 9 of the PSC 2200VS user manual — NOTE
Page 9 · cliquer pour agrandir
Page 9

Volume/Tone Push Button

The Volume/Tone Push Button also performs multiple functions depending upon the duration of time it is pressed:

Volume changes made using the Volume/Tone Push Button are lost when the scanner is powered-down and are reset to the configured set- ting. If you wish to permanently change the volume, use the special programming labels in the Product Reference Guide.

NOTE

Table 1-1. Volume/Tone Push Button Functions

PRESS DURATIONFUNCTIONCOMMENT Momentary (when scanner is asleep)Wakes scanner from Sleep ModeAlternatively, the scanner can be awakened by: - Moving an object through the scan zone. - Scanning with an attached auxiliary scanner. Momentary (when scanner is awake)Increments volumePress the push button momentarily to increase speaker volume. When the loudest volume is reached, a repeated press of the push button cycles volume back to the lowest setting, then volume increases on subsequent press(es). Four volume levels are available. Hold, then release when the beeper soundsIncrements tonePress the push button for approximately 2 seconds, then release. Each time this is done, the beeper will sound at one of three tones. Stop when the desired tone (high, medium or low) is sounded. 4 SecondsScanner Diagnostics ModeaThis mode allows system support personnel to troubleshoot problems with the scanner and is used to determine if it can read bar codes. Press the button for eight seconds or cycle power to exit Scanner Diagnostics Mode and reset the scanner. 8 SecondsResets ScannerbOnly system support personnel should perform a reset.

a. By standard default, this function is normally disabled to prevent accidental activation by users. b. Users should not perform scanner resets except under the direction of trained systems support person-

nel.

Page 10 of the PSC 2200VS user manual — Table 1-2. Green LED Indications
Page 10 · cliquer pour agrandir
Page 10

Green LED Indicator

The green LED indicates scanner status as shown in the table below..

Table 1-2. Green LED Indications

LED INDICATIONDURATIONCOMMENT Scanner Activea (Normal Mode)Scanner (Green) LED on steady and dimThe scanner is ready for operation. Scanning is immediately available. Good Read IndicationaScanner (Green) LED - bright flashIndicates a bar code has been read and decoded. Program Mode IndicationScanner (Green) LED - Continuous flashingIndicates the scanner is in Label Programming Mode. Cycle power to exit Programming Mode. Sleep Mode IndicationScanner (Green) LED flashes slowlyThe scanner motor and/or laser have automatically switched off and the unit has entered Sleep Mode due to extended inactivity. Host DisabledScanner (Green) LED 1-second off, 1/ 10-second onHost has disabled scanning. Field Replaceable Unit (FRU) Warning (Error Mode)Audible low tone 1 second. LED flashes continuously.Serves notice that a fatal FRU failure has been detected. Call systems support for service. FRU IndicationScanner (Green) LED flashes a coded sequence in concert with the speaker.Occurs ONLY upon Volume/Tone button push following a FRU warning. Enables service technicians to identify FRU failures.

a. Certain functions of the LED are selectable to be enabled or disabled. Your scanner may not be pro-

grammed to display all indications.

Page 11 of the PSC 2200VS user manual — NOTE
Page 11 · cliquer pour agrandir
Page 11

Appendix A. Product Labeling

IEC CLASS 1 LASER PRODUCT Class IIa Laser Product. Avoid long term viewing of direct laser light. Appareil á laser de classe IIa. Eviter toute exposition prolongée de la vue à lumière laser directe.

PSC Inc. 959 Terry Street Eugene, OR 97402 USA

XXXXXXXXXXXX

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U S

THIS LASER PRODUCT COMPLIES WITH 21CFR 1040 AS APPLICABLE AS A CLASS IIA PRODUCT This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe A est confirme à la norme NMB-003 du Canada.

N263

PRODUCT SERVICE

NRTL

COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 4,709,195 4,709,369 4,712,853 4,749,879 4,786,798 4,792,666 4,798,943 4,799,164 4,816,660 4,861,972 4,861,973 4,866,257 4,868,836 4,879,456 4,963,719 4,991,692 5,144,118 5,179,270 5,198,649 5,247,162 5,229,588 5,410,108 5,459,308 5,440,110 5,475,207 5,493,108 5,705,802 5,723,852 5,834,708

AVOID DIRECT EYE EXPOSURE.

Use ONLY PSC INC. AC/DC Power Supply Input: 50 - 60 Hz (0.5 - 0.25A)

Output+5V +12V
100. 240VAC (P/N 8-0582) Power: 18 Watts (max)

Scanner Host Power Aux. Port

Labels are shown here to illustrate their location only. Please view the labels on your product for actual details.

NOTE

Show 5 more labels / short text on this page
Product of USA · Safety · tested · Production monitored · EAS Opening
Page 12 of the PSC 2200VS user manual — Appendix B — Productivity Index Reporting Option
Page 12 · cliquer pour agrandir
Page 12

Appendix B — Productivity Index Reporting Option

Productivity Index Reporting™ Option. Your scanner may be equipped with the optional Productivity Index Reporting™ feature. This feature allows for data collection on the readability index of bar codes scanned by the scanner. This data may be transmitted to the POS Terminal where it may be easily sorted for action by the MIS department to improve bar code quality at the front end. For additional information on how to enable Productivity Index Reporting in your scanner, please refer to the Product Reference Guide (PRG)

Option "Productivity Index Reporting™". Votre scanner peut être équipé de l'option "Productivity Index Reporting™" qui permet la collecte de données sur l'index de lecture des codes à barres scannés. Ces données peuvent être transmises vers le Terminal POS où elles pourront être facilement exploitables par le service informatique afin d'améliorer la qualité du code à barres en rayon. Pour plus d'informations sur la manière d'activer PIR sur vos scanners, merci de vous reporter au Product Reference Guide (PRG).

Productivity Index Reporting™ Option. Ihr scanner kann optional mit der Funktion Productivity Index Reporting™ ausgestattet werden. Diese Funktion sammelt Daten zur Lesbarkeit von Barcodes. Diese Daten können ans POS Termi- nal übermittelt werden. Dort können die Daten durch die MIS Abteilung zur Ver- besserung der Barcodequalität sortiert werden. Für weitere Informationen, wie Sie das Productivity Index Reporting in Ihrem Scanner aktivieren können, entnehmen Sie dem Product Reference Guide (PRG).

Opzione Indice di Produttività. Il scanner può essere fornito con l'opzione Productivity Index Reporting™. Quest'opzione permette il controllo della qualità dei barcode letti dello scanner. Questi dati possono essere trasmessi al POS dove possono essere facilmente analizzati dai sistemi informativi per migliorare la qualità dei barcode stessi. Per maggiori informazioni su come abilitare il Productivity Index Reporting nel scanner far riferimento al Product Reference Guide (PRG).

Page 13 of the PSC 2200VS user manual — Opção de Informe de Índice de Produtividade (Productivity Index
Page 13 · cliquer pour agrandir
Page 13

Opcion de Productivity Index Reporting. Su escaner puede ser epuipado con el opcional Indice de Productivity Index Reporting™. Esta funcion permite colectar datos en el indice de la lectura de los codigos de barras por el escaner. Estos datos pueden ser transmitidos a la Terminal POS donde puede ser facilmente clas- ificado por el departamento de MIS para meforar la calidad de el codigo de barra en la parte frontera. Para informacion adicional en como abilitar su escaner con el Indice de Productiv- idad Reportada, por favor referirse a la Guia de Referencia de el Producto (PRG).

Opção de Informe de Índice de Produtividade (Productivity Index

ReportingTM). O seu scanner pode estar equipado com a opção do Informe de Índice de Produtividade. Esta opção permite coletar o dado do índice de leitura dos códigos de barras lidos pelo scanner. Este dado pode ser transmitido para o ter- minal PDV, aonde pode ser fácilmente depurado para ações pelo Departamento de Sistemas para melhorar a qualidade dos códigos de barras na frente de caixas. Para informações adicionais ou como habilitar o Informe do Índice de Produtiv- idade em seu scanner, por favor consultar o Guia de Referência do Produto (PRG - Product Reference Guide).

PSC 2200VS — Opção de Informe de Índice de Produtividade (Productivity Index diagram (page 13)
Fig. 2 · Opção de Informe de Índice de Produtividade (Product…
Page 14 of the PSC 2200VS user manual — Appendix C. Laser Safety
Page 14 · cliquer pour agrandir
Page 14

Appendix C. Laser Safety

International Caution Statements

Class I

English This scanner is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1:2001.

Class I and Class IIa products are not considered to be hazardous. The scanner contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations.

  • CAUTION
  • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light.
  • Do not attempt to open or otherwise service any component in the optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics system is a factory only repair item.
  • Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes and magnifying glasses. This does not include eye glasses worn by the user.

French Ce scanner est certifié conforme à la norme DHHS/CDRH 21CFR sous-chapitre J et à la norme IEC 825-1:2001.

Les produits de classe I et de classe II ne sont pas considérés dangereux. Le scanner contient une diode laser visible (VLD) dont les émis- sions ne dépassent pas les limites prescrites dans les normes précitées. Le scanneur est conçu de façon à ce qu’il ne soit pas possible d’accéder à la lumière laser pendant l’utilisation normale, l’entretien par l’utilisateur et les fonctions de maintenance prescrites.

  • ATTENTION
  • L’utilisation de procédures de contrôle, réglage ou utilisation autres que celles spécifiées dans ce document peut entraîner une exposition dangereuse à la lumière du laser.
  • Ne pas essayer d’ouvrir ni de réparer les composants de la cavité optique. L’ouverture ou la réparation d’une partie de la cavité optique par une personne non qualifiée peut entraîner la violation des règles de sécurité relatives au laser. Le système optique ne peut être réparé qu’en usine.
  • Sont considérés comme instruments optiques les jumelles, les microscopes et les loupes. Les lunettes portées par l'utilisateur ne sont pas considérées comme tel.

German Dieser Scanner ist den in den Vereinigten Staaten geltenden Vorschriften des DHHS/CDRH 21 CFR Subchapter J und den Vorschriften der IEC 825-1:2001 entsprechend bescheinigt.

Produkte der Klasse I oder der Klasse II sind als ungefährlich eingestuft. Im Inneren des Scanners befindet sich eine VLD (Visible Laser Diode), deren Ausstrahlung die in den oben genannten Vorschriften angeführten Höchstgrenzen nicht überschreitet. Die Konstruktion des Scanners garantiert, daß bei normalem Betrieb, bei Wartung durch den Benutzer oder im Laufe planmäßiger Wartungsarbeiten kein Zugang zu schädlichem Laserlicht besteht.

  • VORSICHT
  • Jegliche Anwendung von Streuungen, Reglern oder anderen Verfahren, die nicht in diesen Ausführungen erwähnt werden, können eine gefährliche Laserlichtbestrahlung zur Folge haben.
  • Das optische System darf nur vom Werk repariert werden. Das Öffnen oder Warten von Bestandteilen des optischen Hohlraums durch unbefugtes Personal verletzt die Laser-Sicherheitsbestimmungen.
  • Der Gebrauch von optischen Instrumenten zusammen mit dem Scanner steigert die Gefahr der Augenschädigung. Zu optischen Instrumenten gehören Ferngläser, Mikroskope und Lupen, aber nicht vom Benutzer getragene Brillengläser.

Italian È stato certificato che questo scanner si conforma ai requisiti della sezione J della normativa DHHS/CDRH 21CFR, e anche ai requisiti di IEC 825-1:2001.

I prodotti di Classe I o Classe II non sono considerati pericolosi. Lo scanner contiene al suo interno un Visible Laser Diode (VLD), diodo laser visibile, le cui emissioni non eccedono i limiti stabiliti dalle normative sunnominate. Lo scanner è progettato in modo che non ci sia alcun accesso alla luce dannosa del laser nel corso di uso normale, di manutenzione da parte dell’utente o durante la manutenzione peri- odica stabilita.

Page 15 of the PSC 2200VS user manual — Appendix C. Laser Safety
Page 15 · cliquer pour agrandir
Page 15
  • ATTENZIONE
  • l’uso di comandi o di procedure diversi da quelli specificati in questa sede possono causare l’esposizione ad una luce laser pericolosa.
  • evitare di tentare di aprire o riparare dei componenti nella cavità ottica. L’apertura o la riparazione della cavità ottica da parte di persone non autorizzate può essere in violazione dei regolamenti di sicurezza relativi all’impiego di raggi laser. Il sistema ottico può essere riparato soltanto in fabbrica.
  • l’impiego di strumenti ottici assieme al lettore fa aumentare il rischio di danni alla vista. Il termine “strumenti ottici” sta ad indicare binocoli, microscopi o lenti d’ingrandimento, ma esclude eventuali occhiali da vista indossati dall’utilizzatore.

Danish Denne scanner opfylder de amerikanske krav stillet i "DHHS/CDRH 21CFR Subchapter J" og opfylder også de krav, der stilles i IEC 825-1:2001.

Klasse I eller klasse II produkter anses for at være sikre. Scanneren indeholder en Visible Laser Diode (VLD), der ikke overskrider maksi- mumgrænserne, som beskrevet i ovenstående reglement. Scanneren er konstrueret, så der ikke er nogen menneskelig kontakt medskade- lige niveauer af laserbestråling under normal brug, normal vedligeholdelse eller under foreskrevet servicering.

  • ADVARSEL
  • Udførsel af eftersyn eller justeringer eller anvendelse af andre procedurer end foreskrevet i vejledningen, kan medføre at man udsættes for skadeligt laser lys.
  • Forsøg ikke at åbne eller på anden vis udføre service på komponenter i det optiske hulrum. Uautoriseret åbning eller service af dele af det optiske hulrum, kan betyde overtrædelse af Laser sikkerheds regulativerne. Det optiske system må kun repareres af fabrikken.
  • Brug af optiske instrumenter med scanneren vil forøge faren for øjenbeskadigelser. Optiske instrumenter indbefatter kikkerter, mikroskoper og forstørrelsesglas. Det indbefatter ikke briller båret af brugeren.

Dutch Deze scanner is in de V.S. goedgekeurd en voldoet aan de vereisten van DHHS/CDRH 21CFR Subchapter J een aan de vereisten van IEC 825-1:2001.

Producten van klasse I (Class I) en klasse II (Class II) worden niet geacht gevaarlijk te zijn.

De scanner bevat een inwendige Visible Laser Diode (VLD) waarvan de emissies de maximumgrenzen van bovenstaande reglementen niet overschrijden.

De scanner is zo ontworpen dat men bij normaal gebruik, onderhoud of tijdens het uitvoeren van de voorgeschreven onderhoud- swerkzaamheden niet aan schadelijke niveaus wordt blootgesteld.

  • WAARSCHUWING
  • Men kan aan gevaarlijk laserlicht worden blootgesteld als de apparaten niet goed worden bediend of afgesteld, of als de procedures niet worden uitgevoerd zoals hierin beschreven staat.
  • Probeer niet om onderdelen in de opticaruimte te openen of er op enige wijze onderhoud aan uit te voeren. Openen of onderhoud van onderdelen van de opticaruimte door onbevoegd personeel kan in strijd zijn met de laserveiligheidsreglementen. Het opticasysteem mag alleen in de fabriek worden gerepareerd.
  • Gebruik van optische instrumenten met de scanner vergroot het gevaar dat de ogen aan schadelijke niveaus van laserlicht worden blootgesteld. Optische instrumenten zijn onder meer verrekijkers, microscopen en vergrootglazen. Zo de gebruiker een bril draagt, valt die niet onder optische instrumenten.

Swedish Denna scanner uppfyller de amerikanska kraven DHHS/CDRH 21CFR Subchapter J samt kraven i IEC 825-1:2001.

Produkter i Klass I (Class I) och Klass II (Class II) anses ej farliga. Scannern är utrustad med en intern, synlig laserdiod (Visible Laser Diode - VLD) vars emission inte överstiger max. värdena i ova stående säkerhetsföreskrifter. Scannern har konstruerats så att personer vid normal användning, bruksunderhåll och föreskriven service inte utsätts för skadlig laserstrålning.

  • VARNING
  • Om apparaten används på annat sätt än som specificerats i denna bruksanvisning kan användaren utsättas för farlig laserstrålning.
  • Försök inte öppna eller reparera komponenter i den optiska kammaren. Om icke auktoriserad personal öppnar eller reparerar delar i den optiska kammaren, kan detta vara ett brott mot säkerhetstföreskrifterna för laserutrustning. Det optiska systemet får endast repareras i fabriken.
  • Om optiska instrument används tillsammans med scannern ökar risken för ögonskador. Optiska instrument omfattar kikare, mikroskop och förstoringsglas. Glasögon som bärs av användaren omfattas ej av detta.
Page 17 of the PSC 2200VS user manual — Japanese
Page 17 · cliquer pour agrandir
Page 17

Chinese

PSC 2200VS — Chinese diagram (page 17)
Fig. 3 · Chinese

Japanese

PSC 2200VS — Japanese diagram (page 17)
Fig. 4 · Japanese
Page 18 of the PSC 2200VS user manual — Hebrew
Page 18 · cliquer pour agrandir
Page 18

Hebrew

PSC 2200VS — Hebrew diagram (page 18)
Fig. 5 · Hebrew
Page 19 of the PSC 2200VS user manual — NOTES
Page 19 · cliquer pour agrandir
Page 19

NOTES

Page 20 of the PSC 2200VS user manual — Appendix D. Warranty
Page 20 · cliquer pour agrandir
Page 20

Appendix D. Warranty

PSC warrants to Customer that PSC's products will be free from defects in materials and workmanship for a period of 1 year from product shipment. In order to obtain service under this Warranty, Customer must notify PSC of the claimed defect before the expiration of the Warranty period and obtain from PSC a return authorization number for return of the product to designated PSC service center. If PSC determines Customer’s claim is valid, PSC will repair or replace product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated PSC service center, with shipping charges prepaid. PSC shall pay for the return of the prod- uct to Customer if the shipment is to a location within the country in which the PSC service center is located. Cus- tomer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

Warranty is subject to the limitations and exclusions set forth in the paragraphs that follow.

WARRANTY SET FORTH ABOVE IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD- ING MERCHANTABILITY AND FITNESS.

Warranty coverage shall not apply to any claimed defect, failure or damage which PSC determines was caused by: improper use of product; failure to provide product maintenance, including but not limited to cleaning of the upper win- dow in accordance with product manual; installation or service of product by other than PSC representatives; use of product with any other instrument, equipment or apparatus; modification or alteration of product. External cables and replacement of upper window/cartridge due to scratching, stains or other degradation will not be covered under the Warranty. External power supplies returned for service must be accompanied by the original product for performance of service.

PSC's REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCT AS SET FORTH ABOVE IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY ON ACCOUNT OF CLAIMS OF BREACH OF WARRANTY OR PRODUCT DEFECT. UNDER NO CIRCUMSTANCES WILL PSC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES REGARDLESS OF WHETHER PSC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Customer may not assign or otherwise transfer its rights or obligations under Warranty except to a purchaser or trans- feree of product. No attempted assignment or transfer in violation of this provision shall be valid or binding upon PSC.

Customer shall bear risk of loss or damage for product in transit to PSC. PSC shall assume risk of loss or damage for product in PSC's possession or product being returned to Customer by PSC, except such loss or damage as may be caused by the negligence of Customer, its agents or employees. In the absence of specific written instructions for the return of product to Customer, PSC will select the carrier, but PSC shall not thereby assume any liability in connection with the return shipment.

Show 5 more labels / short text on this page
Warranty · Exclusions · Limitation of Liability · Assignment · Risk of Loss
Page 21 of the PSC 2200VS user manual — Appendix D. Warranty
Page 21 · cliquer pour agrandir
Page 21
Page 21 of the PSC 2200VS user manual — Appendix D. Warranty
Page 22 of the PSC 2200VS user manual — NOTES
Page 22 · cliquer pour agrandir
Page 22

NOTES

Page 23 of the PSC 2200VS user manual — compliant to the following Directives and Standards:
Page 23 · cliquer pour agrandir
Page 23

DECLARATION OF CONFORMITY

PSC hereby declares that the Equipment specified below has been tested and found

compliant to the following Directives and Standards:

DirectivesEMC 89/336/EEC Low Voltage 73/23/EEC

Standards: EN55022-13:1998 Generic Emissions EN60950:2000 ITE Safety EN55024:1998 Generic Immunity-ITE CISPR 22-B:1997 Generic Emissions EN60825-1:2001 Laser Safety

Equipment TypeBarcode Scanning Equipment
ProductMagellan ® 2200VS
PSC 2200VS — compliant to the following Directives and Standards: diagram (page 23)
Fig. 6 · compliant to the following Directives and Standards:
PSC 2200VS — compliant to the following Directives and Standards: diagram (page 23)
Fig. 7 · compliant to the following Directives and Standards:

Brad West Vice President Quality and Process Management PSC, Inc. 959 Terry Street Eugene, OR 97402 U.S.A.

Peter Lomax Vice President Europe, Middle East & Africa PSC Bar Code Ltd. Axis 3, Rhodes Way Watford Hertfordshire WD24 4TR UK

Page 24 of the PSC 2200VS user manual — www.psc.com
Page 24 · cliquer pour agrandir
Page 24

Asia Pacific PSC Hong Kong Hong Kong Telephone: [852]-2-584-6210 Fax: [852]-2-521-0291

Italy PSC S.p.A. Vimercate (MI), Italy Telephone: [39] (0) 39/62903.1 Fax: [39] (0) 39/6859496

Australia PSC Asia Pacific Pty Ltd. North Ryde, Australia Telephone: [61] 0 (2) 9878 8999 Fax: [61] 0 (2) 9878 8688

Japan PSC Japan K.K. Shinagawa-ku, Tokyo, Japan Telephone: 81 (0)3 3491 6761 Fax: 81 (0)3 3491 6656

France PSC S.A.R.L. LES ULIS Cedex, France Telephone: [33].01.64.86.71.00 Fax: [33].01.64 46.72.44

Latin America PSC S.A., INC. Miami, Florida, USA Telephone: (305) 539-0111 Fax: (305) 539-0206

Germany PSC GmbH Darmstadt, Germany Telephone: 49 (0) 61 51/93 58-0 Fax: 49 (0) 61 51/93 58 58

United Kingdom PSC Bar Code Ltd. Watford, England Telephone: 44 (0) 1923 809500 Fax: 44 (0) 1923 809 505

www.psc.com

PSC Inc. 959 Terry Street Eugene, OR Telephone: (541) 683-5700 Fax: (541) 345-7140

©2002-2005 PSC INC. R44-2364 (Rev. G) 5/05

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : PSC 2200VS

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le PSC 2200VS

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

PSC 2200VS manuel PDF

48 pages·2.7 MB·Scanner·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…