FR
Phase Technology logo
Notice d'utilisation officielle

Phase Technology CL-1.5

3 pages·747 KB·Enceinte·PDF·EN
Phase Technology CL-1.5
Table des matières 3 sections Power FL-8 Power FL-10 Power FL-12 CI-1.5 · Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling · Installation Instructions: Installing the CI-1.5 Using Optional Pre-Construction Bracket AfficherMasquer
Page 1 of the Phase Technology CL-1.5 user manual — R
Page 1 · cliquer pour agrandir
Page 1

T E C H N O L O G Y Custom Installation Series Owners Manual / Installation Instructions

R

Power FL-8 Power FL-10 Power FL-12 CI-1.5

Speaker seismic restraint hole

1 Speaker 1 Grille 1 Paint mask 1 Hole template 1 Euroblock connector

MSE Audio Group 8650 College Boulevard Overland Park, Kansas 66210 (866) 663-9770

www.mseaudio.com www.phasetech.com

Show 6 more labels / short text on this page
SpeedWing™ mounting arms · Baffle · Installation aid/paint mask · Grille safety clip · Grille · Box contents
Page 2 of the Phase Technology CL-1.5 user manual — Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling
Page 2 · cliquer pour agrandir
Page 2
Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling diagram (page 2)
Fig. 1 · Installation Instructions: Installing the CI-1.5 in…

Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling

T E C H N O L O G Y

Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling diagram (page 2)
Fig. 2 · Installation Instructions: Installing the CI-1.5 in…
1. Unpack speaker. Leave paint mask in place until after speaker is installed or painting is complete.
2. Use hole template to mark cutout on sheetrock.
3. Use RotoZip or other tool to cut hole. Hole diameter: 5.6 in. (142 mm).
4. Connect Euroblock to speaker wires, and connect to speakers.
Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling diagram (page 2)
Fig. 3 · Installation Instructions: Installing the CI-1.5 in…
5. If required, attach seismic restraint system to hole in clamping arm, then to reinforced structure (safety cable not included).
6. Insert speaker into mounting hole with paint mask in place. Tighten both screws on the baffle face to actuate the mounting wings. Firmly secure both screws, DO NOT OVERTIGHTEN .
7. Remove paint mask unless painting is required. In that case, follow steps 8-11 when painting is complete.
8. Adjust tap switch to proper setting. Switch is preset to 8-ohm mode.
Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 in a Sheetrock Ceiling diagram (page 2)
Fig. 4 · Installation Instructions: Installing the CI-1.5 in…
9. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
10. Align tabs on snap-fit grille with slots in baffle, gently press grille into place.
11. Done!
Page 3 of the Phase Technology CL-1.5 user manual — Installation Instructions: Installing the CI-1.5 Using Optional Pre-Construction Bracket
Page 3 · cliquer pour agrandir
Page 3
Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 Using Optional Pre-Construction Bracket diagram (page 3)
Fig. 5 · Installation Instructions: Installing the CI-1.5 Usi…

Installation Instructions: Installing the CI-1.5 Using Optional Pre-Construction Bracket

T E C H N O L O G Y

Phase Technology CL-1.5 — Installation Instructions: Installing the CI-1.5 Using Optional Pre-Construction Bracket diagram (page 3)
Fig. 6 · Installation Instructions: Installing the CI-1.5 Usi…
3. Use RotoZip or other tool to cut hole.
4. Unpack speaker. Leave paint mask in place until after speaker is installed or painting is complete.
5. Connect euroblock to speaker wires, and connect to speakers.
6. If required, attach seismic restraint system to the sheet-metal tab on the rear panel of the speaker, then to reinforced structure (safety cable not included).
7. Insert speaker into mounting hole. Tighten both screws on the baffle face to actuate the mounting wings. DO NOT OVERTIGHTEN .
8. Remove paint mask unless painting is required. In that case, follow steps 9-12 when painting is complete.
9. Adjust tap switch to proper setting. Switch is preset to the 8-ohm mode.
10. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
11. Align tabs on snap-fit grille with slots in baffle, gently press grille into place.
12. Done!
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Phase Technology CL-1.5

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Phase Technology CL-1.5

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Phase Technology CL-1.5 manuel PDF

3 pages·747 KB·Enceinte·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…