FR
Phase Technology logo
Notice d'utilisation officielle

Phase Technology CI-15

3 pages·855 KB·Enceinte·PDF·EN
Phase Technology CI-15
Table des matières 2 sections Installation Instructions: Installing the CI-15 in an Existing Wall · Installation Instructions: Installing the CI-15 Using the Pre-Construction Bracket AfficherMasquer
Page 1 of the Phase Technology CI-15 user manual
Page 1 · cliquer pour agrandir
Page 1
Phase Technology CI-15 diagram (page 1)
Fig. 1

T E C H N O L O G Y Custom Installation Series Owners Manual / Installation Instructions

Phase Technology CI-15 diagram (page 1)
Fig. 2

1 Speaker 1 Grille 1 Paint mask 1 Cutout hole template 1 Euroblock connector

MSE Audio Group 8650 College Boulevard Overland Park, Kansas 66210 (888) PHASE-TK

www.mseaudio.com www.phasetech.com

Box contents · Euroblock connector

Page 2 of the Phase Technology CI-15 user manual — R
Page 2 · cliquer pour agrandir
Page 2

R

Installation Instructions: Installing the CI-15 in an Existing Wall

T E C H N O L O G Y

1. Unpack speaker. Leave paint mask in place until after speaker is installed or painting is complete.
2. Use provided cutout template to mark hole. Use RotoZip or other tool to cut hole in wall. Hole size: 4 in. (102 mm) tall x 4 in. (102 mm) wide.
4. If required, attach seismic restraint system to the hole in the metal clamping arm, then to reinforced structure (safety cable not included).
3. Connect Euroblock to speaker wires, and connect to speakers.
5. Insert speaker in hole. Tighten the two clamping screws. DO NOT OVERTIGHTEN .
6. Remove paint mask unless painting is required. In that case, follow steps 7-10 when painting is complete.
7. Adjust tap switch to proper setting. Switch is preset to the 8-ohm mode.
8. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
Phase Technology CI-15 — R diagram (page 2)
Fig. 3
9. Align tabs on snap-fit grille with slots in baffle, gently press grille into place.
10. Done!
Page 3 of the Phase Technology CI-15 user manual — R
Page 3 · cliquer pour agrandir
Page 3

R

Installation Instructions: Installing the CI-15 Using the Pre-Construction Bracket

T E C H N O L O G Y

1. Nail or screw bracket to studs.
2. Finish installing wall. 3. Use RotoZip or other tool to cut hole.
4. r. Leave paint mask in place until after speaker is installed or painting is complete.
5. Connect Euroblock to speaker wires, and connect to speakers.
6. If required, attach seismic restraint system to the hole in the metal clamping arm, then to reinforced structure (safety cable not included).
7. Insert speaker in hole. Tighten the two clamping screws. DO NOT OVERTIGHTEN .
8. Remove paint mask unless painting is required. In that case, follow steps 9-12 when painting is complete.
9. Adjust tap switch to proper setting. Switch is preset to the 8-ohm mode.
10. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
11. Align tabs on snap-fit grille with slots in baffle, gently press grille into place.
12. Done!

Unpack speake

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Phase Technology CI-15

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Phase Technology CI-15

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Phase Technology CI-15 manuel PDF

3 pages·855 KB·Enceinte·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…