Manuel d'utilisation / d'entretien du produit DX8000-UPDVD du fabricant Pelco
Aller à la page of 24
DX8000-UPDVD Upgrade Installation Manual C1604M (6/04) Digital Video Recorder DX8000.
Protecting people and property in a million locations worldwide..
C1604M (6/04) 1 Introduction The following instructions serve as an installation guide for the DX8000-UPDVD drive kit. PARTS LIST NOTE: This upgrade kit includes a Pelco-certified DVD-RW drive. Using any other drive voids the manufacturer’ s warranty for the DX8000.
2 C1604M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools.
C1604M (6/04) 3 Figure 2. Removing Power Cord from Unit.
4 C1604M (6/04) Figure 3. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit.
C1604M (6/04) 5 Prepare Unit for Drive Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components.
6 C1604M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section.
C1604M (6/04) 7 4. Using a Phillips-head screwdriver , remove the side panel from the side of the unit closest to the CD/DVD drive: a. Remove the four screws from the side panel. Refer to Figure 5. b. Set the panel and screws aside for use later . Figure 5.
8 C1604M (6/04) COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity .
C1604M (6/04) 9 Remove the Existing Optical Drive DISCONNECT THE CD/DVD DA T A CABLE AND POWER WIRES When removing data cable and power wires, pull the connectors straight out. Do not rock connectors back and forth or remove a connector by pulling it by its wires or cable.
10 C1604M (6/04) 2. Remove the power connector from the CD/DVD drive. Refer to Figure 8. 2 Figure 8. Removing the CD/DVD Power Connector.
C1604M (6/04) 11 REMOVE THE CD/DVD DRIVE 1. Using a Phillips-head screwdriver , unfasten the two screws that attach the CD/DVD to the chassis. Refer to Figure 9.
12 C1604M (6/04) 2. Gently pull the CD/DVD drive out of the DVR through the front of the unit. Refer to Figure 10. 2 Figure 10. Removing the Existing Optical Drive.
C1604M (6/04) 13 Install the New DVD-RW Drive into the Unit 1. Insert the new DVD-RW into the DVR: a. Make sure the drive is oriented correctly . b. Insert the new DVD-RW into the DVR through the front of the unit.
14 C1604M (6/04) c. Using a Phillips-head screwdriver and the two screws provided in the upgrade kit, secure the drive to the unit’ s chassis. Refer to Figure 12.
C1604M (6/04) 15 RECONNECT THE DA T A CABLE AND POWER WIRES IMPORT ANT : Data and power connectors fit together only one way . All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard and cable connectors before installation so that connectors are properly aligned.
16 C1604M (6/04) 2. Connect the DVD-RW drive to the system motherboard using the existing data cable. Refer to Figure 14. 2 Figure 14. Installing DVD-RW Data Cable.
C1604M (6/04) 17 Reassemble the Unit 1. Using a Phillips-head screwdriver , reattach the side panel you removed earlier . Refer to Figure 15. Figure 15.
18 C1604M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 16. Figure 16. Replacing Chassis Cover.
C1604M (6/04) 19 4. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 3. Plug the power cord back into the power supply and then into the wall. 4. T urn on the power switch and allow the unit to start up and find the new DVD-RW .
20 C1604M (6/04) Notes.
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco DX8000-UPDVD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco DX8000-UPDVD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco DX8000-UPDVD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco DX8000-UPDVD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco DX8000-UPDVD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco DX8000-UPDVD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco DX8000-UPDVD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco DX8000-UPDVD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.