Manuel d'utilisation / d'entretien du produit 350P du fabricant Miller Electric
Aller à la page of 56
Millermatic 350 And Millermatic 350P Processes Description R Arc W elding Power Source and Wire Feeder OM-1327 213 814AD 2010 − 04 MIG (GMAW) W elding Pulsed MIG (GMAW -P) Flux Cored (FCA W ) W elding R File: MIG (GMA W) V isit our website at www.MillerWelds.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ABLE OF CONTENTS SECTION 5 − PROGRAMMING 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1. MIG Welding Mode 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1327 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _2010 − 03 7 Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury .
OM-1327 Page 2 W elding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. FUMES AND GASES can be hazardous. D Keep your head out of the fumes. Do not breathe the fumes. D If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases.
OM-1327 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-1327 Page 4 1-4. California Proposition 65 W arnings W elding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.
OM-1327 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION fre_som_2010 − 03 7 Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-1327 Page 6 Il reste une TENSION DC NON NÉGLIGEABLE dans les sources de soudage onduleur UNE FOIS l’alimentation coupée. D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces.
OM-1327 Page 7 LES ACCUMULA TIONS DE GAZ risquent de provoquer des blessures ou même la mort. D Fermer l’alimentation du gaz protecteur en cas de non-utilisation. D V eiller toujours à bien aérer les espaces confi- nés ou se servir d’un respirateur d’adduction d’air homologué.
OM-1327 Page 8 Les PIÈCES MOBILES peuvent causer des blessures. D Ne pas s’approcher des organes mobiles. D Ne pas s’approcher des points de coincement tels que des rouleaux de commande. LES FILS DE SOUDAGE peuvent provoquer des blessures. D Ne pas appuyer sur la gâchette avant d’en avoir reçu l’instruction.
OM-1327 Page 9 2-5. P r i nc ip al e s no r m e s de sé c ur i té Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www .
OM-1327 Page 10.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 1 1 SECTION 3 − INST ALLA TION 3-1. Specifications Rated Output Max. Open Circuit V oltage 60 Hz Amps Input at Rated Output 200 V 230 V 460 V 575V KV A KW 300 A at 32 VDC, 60% Duty Cycle 350 A at 32 VDC, 40% Duty Cycle 90 Single-Phase 69 (1.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 12 3-3. V olt-Ampere Curve 217 443-A 1 Normal Volt-Ampere Curves The volt-ampere curves show the normal minimum and maximum voltage and amperage output capabilities of the welding power source.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 13 3-5. Installing W ork Clamp 1 Work Cable 2 Boot Route cable through front panel opening. Slide boot onto work cable. 3 Negative ( − ) Output T erminal Connect cable to terminal and cover connection with boot.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 14 3-7. Installing W elding Gun 1 Drive Assembly 2 Gun Securing Knob 3 Gun End Loosen securing knob. Insert gun en d through opening until it bottoms against drive assembly (make sure gun end does not touch drive rolls).
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 15 3-8. Connecting Spoolmatic ) 15A Or 30A Gun 803 568-D 1 Gu n T rigger Plug Insert plug into receptacle, and tighten threaded collar . 2 Weld Cable 3 Shielding Gas Hose Route weld cable and gas hose through opening in front panel.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 16 3-9. Connecting XR Edge, XR-A Gun, XR-A Python, Or XR - Aluma-Pro 803 569-C / Ref. 803 570 -C / Ref. 803 463 . XR E dge g uns prior to serial n o. LE079101 require an adapter cor d (part no.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 17 3-10. Setting Gun Polarity For Wire T ype 1 Polarity Changeover Information Always read and follow manufacture’s recommended polar ity .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 18 3-1 1. Installing Gas Supply 803 542-C T ools Needed: 1-1/8, 5/8 in. 1 2 3 4 5 7 Rear Panel 6 Obtain gas cylinder and chain to running gear , wall, or other stationary support so cylinder cannot fall and break off valve.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 19 3-12. Installing Wire Spool and Adjusting Hub T ension Ref. 805 023-A When a slight force is needed to turn spool, tension is set. 15/16 in. Use compression spring with 8 in (200 mm) spools.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 20 3-14. Selecting Input V oltage (200/230/460 V olt Models Only) 803 539-C / 804 042-A ! T urn Off welding power source, disconnect input power , and check voltage on input capacitors according to Section 6-3 before proceeding.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 21 3-15. Serial Number And Rating Label Location Th e serial number and rating information for this product is located on back. Use rating label to determine input power requirements and/or rated output.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 22 3-17. Selection A Location And Connecting 1-Phase Input Power Ref. 803 543-E / 803 766-A T ools Needed: 3 2 7 6 4 ! Installation must meet all National and Local Codes - have only qualified persons make this installation.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 23 3-18. Threading W elding Wire For MIG Gun 1 Wire Spool 2 Welding Wire 3 Inlet Wire Guide 4 Drive Roll 5 Intermediate Wire Guide 6 Outlet Wire Guide 7 Pressure Adjustment Knob 8 Gun Conduit Cable Lay gun cable out straight.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 24 3-19. Threading W elding Wire For XR Edge, XR-A Gun, XR-A Python, Or XR - Aluma-Pro 1 Wire Spool 2 Welding Wire 3 Inlet Wire Guide 4 Drive Roll 5 Intermediate Wire Guide 6 Outlet Wire Guide 7 Pressure Adjustment Knob 8 Gun Conduit Cable Lay gun cable out straight.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 25 3-20. Threading W elding Wire Through XR Guns Ref. 802 193-A / 801 556 / Ref. 151 666-C T ools Needed: ! W elding wire is electrically live when gun trigger is used to jog wire.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 26 SECTION 4 − OPERA TION 4-1. Controls 1 Pulse Indicator Light . Pulse only lights if unit has the pulse MIG module and is programmed for pulse MIG. 2 MIG Indicator Lights Pulse (1) and MIG (2) illuminate to Indicate weld mode of unit.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 27 because gas valve is located inside spool gun. For MIG guns, wire will feed for up to 2 minutes while trigger is pressed, then wire drive system in unit will automatically shut off.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 28 4-9. W eld Parameters For MIG Mode Material Steel Steel Aluminum Stainless Steel Gas 100% Co 2 75% Argon 25% Co 2 90% Helium 7.5% Argon 2.5% Co 2 100% Argon Wire 1/2” 3/8” 1/4” 3/16” 1/8” 14ga 16ga 18ga 20ga 22ga 3/64 5356 24.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 29 4-10. W eld Parameters For Pulse Mode .045 .045 3/644043 3/645356 .0355356 WELDCHARTS 3/16” (4.8mm) 1/8” (3.2mm) 14ga (2.0mm) 16ga (1.6mm) 18ga (1.2mm) 19ga (1.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 30 SECTION 5 − PROGRAMMING 5-1. MIG Welding Mode When the MIG light (2) is illuminated, the unit is in MIG W elding mode. SETUP T o enter MIG welding mode, depress the SETUP (6) button once to go to GUN selection.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 31 5-2. Pulse MIG Welding Mode When the PULSE MIG (1, 2) is illuminated, the unit is in Pulse MIG W elding mode. SETUP T o enter Pulse MIG welding mode, depress the SETUP (6) button once to go to GUN selection.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 32 5-3. Timers T o enter the TIMERS (5) menu depress the SETUP (6) button 4 times or until the TIMERS light (5) is illuminated. Items that can be adjusted in this menu are: Run-in speed ( R‐IN ) − The speed of the wire prior to the welding arc being struck.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 33 5-4. Arc T imes, Arc Starts, Hot Start (Aluminum Pulse Only), And Crater Fill Arc times and number of arc starts are saved in unit memory . T o view this information, press both SETUP (1) and ARC CONTROL (2) buttons at the same time.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 34 5-5. Setting Hot Start (Aluminum Pulse Only) Parameters T o access the Setup Feature Menu, press both SETUP (1) and ARC CONTROL (2) buttons at the same time. Left display will initially show arc hours.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 35 5-6. Setting Crater Fill T o set Crater Fill, select a program and press SETUP (1) until the TIMERS LED turns on. Press SETUP again and the left display will show CRTR and the right display will show OFF .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 36 5-7. Recommended Crater Fill Parameters What P r o c e s s a re Y ou U s i ng ? What Ma te r i al a re Y ou W e l d i n g .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 37 SC-187 212-A 19ga. 20ga. ( 0 .9mm) (1.05mm) 3/8” 1/ 4” 3/16” 1/8”.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 38 5-8. System Reset A system reset function is available that completely resets unit back to all the original factory settings. T o access this menu, turn on welding power source, then press the SETUP (1) button when the SETUP light illuminates under the Left display .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 39 5-9. Motor Calibration Function Perform this function after replacing wire drive motor and/or control circuit board. The motor calibration function automatically calibrates the wire drive motor t o enhance arc starting performance and consistency .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 40 . W elding wire birdnesting at the welding power source drive rolls may occur if this value is set too high.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 41 SECTION 6 − MAINTENANCE &TROUBLESHOOTING 6-1. Routine Maintenance ! Disconnect power before maintaining.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 42 221 044-A / Ref. 803 550-B ! Significant DC voltage can remain on capacitors after unit is Off. Always check ca- pacitors as shown to be sure they h ave discharged before working on unit.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 43 6-4. Changing Drive Roll and Wire Inlet Guide 1 Securing Screw 2 Inlet Wire Guide Loosen screw . Slide tip as close t o drive rolls as possible without touching. T ighten screw .
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 44 6-5. Help Displays A V A V A V HELP 0 A V A V A V A V A V A V A V HELP 1 HELP 2 HELP 3 HELP 4 A V HELP 5 A V HELP 6 HELP 8 HELP 9 HELP 10 TIP SA VE MM 350P A V MM 350 A V JOG A V HELP 7 A V HELP 1 1 Displays a jog wire feed speed.
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 45 SC-187 212-A . All directions are in reference to the front of the unit. All circuitry referred to is located inside the unit. S Help 0 Indicates overheating on left side of unit (displays flash between OVER TEMP and HELP 0).
. A complete Parts List is available at www .MillerW elds.com OM-1327 Page 46 6-6. T roubleshooting T rouble Remedy No weld output; wire does not feed. Be sure line disconnect switch is On (see Section 3-16 or 3-17 ). Replace building line fuse or reset circuit breaker if open (see Section 3-16 or 3-17 ).
OM-1327 Page 47 Notes.
OM-1327 Page 48 SECTION 7 − ELECTRICAL DIAGRAM Figure 7-1. Circuit Diagram For Welding Power Source.
OM-1327 Page 49 246 030-B.
OM-1327 Page 50 SECTION 8 − P ARTS LIST 8-1. Drive Roll And Wire Guide Kits . Base selection of drive rolls upon the following recommended usages: 1 V -Grooved rolls for hard wire. 2 U-Grooved rolls for soft and soft shelled cored wires. 3 U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2010 − 01 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.
ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2010 Miller Electric Mfg. Co. 2010 − 01 Miller Elect ric Mfg. Co. An Illinois T ool W o rks Co mpany 1635 West S pencer S treet Applet on, WI 5 4914 US A .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Miller Electric 350P c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Miller Electric 350P - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Miller Electric 350P, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Miller Electric 350P va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Miller Electric 350P, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Miller Electric 350P.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Miller Electric 350P. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Miller Electric 350P ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
