Manuel d'utilisation / d'entretien du produit KRC-225 du fabricant Kenwood
Aller à la page of 21
KRC-235 KRC-225 © B64-2101-00 (KW/KN) CASSETTE RECEIVER INSTR UCTION MANU AL AMPLI-TUNER-LECTEUR DE CASSETTE MODE D’EMPLOI RADIO CASETE MANU AL DE INSTR UCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new cassette-receiver.
— 2 — English Contents Safety precautions .................................................3 About Cassette tape ..................................
— 3 — To prevent injury or fire, take the following precautions: •I nsert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer .
Press the [SRC] button. Source required Display T uner "TUnE" T ape "T APE" External disc (KRC-235 only) "DISC" Standby (Illumination only mode) "OFF" Selecting the Source Tu rning ON the Power Press the [SRC] button.
1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [A.ADJ] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below .
The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.
Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 Tu ne up or down the band Press the [ 4 ] or [ ¢ ] button.
T emporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. Press the [CRSC] button for at least 1 second. Each time the button is pressed CRSC turns ON or OFF . When it's ON, the " "(CRSC) indicator is ON.
Switching to the radio automatically during Fast Forwarding and Rewinding. Press the [TC]/ [T .CALL] button. Each time the button is pressed the T uner Call turns ON or OFF . When it's ON, the "T .CALL" indicator is ON. T uner Call Fast Forwarding Press the [FF] button.
Fast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Playing discs set in the optional accessory disc player connected to this unit.
Playing all the songs on the disc in random order . Press the [RDM] button. Each time the button is pressed Random Play turns ON or OFF . When it's ON, the "RDM" indicator is ON and the track number blinks. When the [ ¢ ] button is pressed, the next song select starts.
Play the songs on all the discs in the disc changer in random order . Press the [M.RDM] button. Each time the button is pressed the Magazine Random Play turns ON or OFF . When it's ON, the "RDM" indicator is ON and the track and disc number blink.
English — 14 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
— 15 — FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT CONT FM/AM antenna input 1 Rear left output (White) 23 Rear right output (Red) 28 Fuse (10A) 24 KENWOOD disc changer control input (.
English — 16 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) ■ Installation 8 mm MAX.
— 17 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level.
English — 18 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. ✔ The fuse has blown.
— 19 — T uner source ? Radio reception is poor . ✔ The car antenna is not extended. ☞ Pull the antenna out all the way . ✔ The antenna control wire is not connected. ☞ Connect the wire correctly , referring to the section on <Connecting Wires to T erminals>.
English — 20 — The messages shown below display your systems condition. E-01: No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. ➪ Load the disc magazine properly . E-02: No disc has been loaded in the disc magazine.
— 21 — FM tuner section Frequency range (200 kHz space) .............87.5 MHz –108.0 MHz Usable sensitivity (S/N = 30dB) ................... 9.3 dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .............. 15.2 dBf (1.6 µV/75 Ω ) Frequency response ( ± 3.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Kenwood KRC-225 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Kenwood KRC-225 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Kenwood KRC-225, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Kenwood KRC-225 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Kenwood KRC-225, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Kenwood KRC-225.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Kenwood KRC-225. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Kenwood KRC-225 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
