Manuel d'utilisation / d'entretien du produit WDR-516S du fabricant DENTEC
Aller à la page of 56
WDR-516S Installation Guide.
FCC Compliance Statement Caution : Any changes or modifications in construc tion of this device which are not expressly approved the party responsible for compliance co uld void the user's authority to operate the equipment.
Important Notice 1. Do not place heavy objects on the top of the WDR-516S. 2. WDR-516S is not weatherproof. In case of outdoor use, equip a weatherproof case to protect WDR- 516S from water , moisture, or temperature (higher or lower than specifications).
WDR-516S Installation Guide 4 Rev 1.0(93/1 1) OVERVIEW ....................................................................................................................... ........... 7 1. What is WDR-516S? .........................................
WDR-516S Installation Guide 5 Rev 1.0(93/1 1) 8.2.2. Daylight Saving ..................................................................................................... 22 8.2.3. T ime Format .........................................................
WDR-516S Installation Guide 6 Rev 1.0(93/1 1) 14.3. Available HDD .......................................................................................................... 36 14.4. Registering & Form atting HDD ...................................
WDR-516S Installation Guide 7 Rev 1.0(93/1 1) OVER VIEW 1. What is WDR-516S? The WDR-516S is a 4-Analog, 12-IP channel network digital video recorder . The WDR-516S can record and display 4 analog video channels and 12 IP video channels simultaneously .
WDR-516S Installation Guide 8 Rev 1.0(93/1 1) 2. Supplied Accessories Unpack and check all the items as below . 1. WDR-516S (1) 2. DC Power Supply (1) (1 10V~220V) 3. AC Power Cord (1) 4. CD-ROM (Including WDR Manager) (1) 5. Remote Controller (1) 6. Guide (2) 7.
WDR-516S Installation Guide 9 Rev 1.0(93/1 1) 3. Description & Function WDR-516S Front (1) LED (2) IEEE1394 connecter (3) Remote controller receiver (4) USB connecter (5) Function buttons (6) Brac.
WDR-516S Installation Guide 10 Rev 1.0(93/1 1) WDR-516S Rear (7) Power switch (8) Ethernet connector (9) BNC connector for V ideo input (10) Audio input / output connector (1 1) RS232 connecter (9Pin .
WDR-516S Installation Guide 11 Rev 1.0(93/1 1) INST ALLA TION AND CONNECTION 4. Connecting & Running WDR-516S 4.1. Connecting camera (1) Connect CCTV camera to WDR-516S with BNC cable as shown below . (2) Set video type (NTSC/P AL) by rear panel’ s switch.
WDR-516S Installation Guide 12 Rev 1.0(93/1 1) 4.2. Connecting Monitor (1) Connect CCTV monitor to WDR-516S with BNC cable as shown below . <Note> WDR-516S has two video output ports ; for Monitor and VCR. The output signals from the two ports are same and either port may be used.
WDR-516S Installation Guide 13 Rev 1.0(93/1 1) 4.4. Supplying Power (1) Connect power cable to WDR-516S. (2) T urn on the power switch located on the WDR-516S rear panel. <Note> Use the plug bracket to secure the power cable if needed. <Note> T o connect EAR TH, refer to the following picture.
WDR-516S Installation Guide 14 Rev 1.0(93/1 1) 5. Running OSD menu 5.1. Using menu Press the [MENU] button to open the OSD Configuration Menu. (1) Main Menu T abs : The selected tab is shown in blue and the related sub-menus will be shown below the tab.
WDR-516S Installation Guide 15 Rev 1.0(93/1 1) 5.2. Dialogue Box to Edit a Word There are two methods to set word. (1) Using number button Enter the related numbers in order of horizontal/v ertical. (For example, in order to select “ C ” , p r e s s [3] and [2] buttons.
WDR-516S Installation Guide 16 Rev 1.0(93/1 1) 6. Setting remote controller 6.1. Setting remote control DIP switch Set the remote control DIP switch to “ON.” 6.2. Set ID of WDR-516S When controlling several WDR-516S with one remote controller , set Remote Control ID as follows.
WDR-516S Installation Guide 17 Rev 1.0(93/1 1) (3) Select “Miscellaneous” from the sub-menu list using the [ ▼ ] button and press the [ENETR] button. (4) Select “Remote Control ID,” and press the [ENETR] button. (5) Select a value using the [ ◄ or ► ] buttons and press the [EXIT] button.
WDR-516S Installation Guide 18 Rev 1.0(93/1 1) WDR 6.4. Operable range of remote controller 6.5. Loading the batteries into remote controller Remote controller requires two AAA-type batteries. 1. Remove the battery cover . 2. T aking care that the poles(+/-) are correctly positioned.
WDR-516S Installation Guide 19 Rev 1.0(93/1 1) 7. WDR-516S Configuration 7.1. Basic Configuration 7.2. Advanced Configuration.
WDR-516S Installation Guide 20 Rev 1.0(93/1 1) 7.3. External Storage & Backup Configuration 7.4. Internet/Intranet Configuration WDR.
WDR-516S Installation Guide 21 Rev 1.0(93/1 1) 8. WDR-516S Basic Setting 8.1. Viewing Image After initial start-up, images from Ch.1~4 are displayed in a quad-split screen. <Note> If user password is set, a prompt for entering the password will appear .
WDR-516S Installation Guide 22 Rev 1.0(93/1 1) 8.2. Setting Date & Time (1) Press [MENU] button, and select “Quick Setup” tab. (2) Select “Date/T ime” and enter the Settings Page by pressing [ENTER]. 8.2.1. Time Zone (1) Select “T ime Zone” and press [ENETR] button to configure.
WDR-516S Installation Guide 23 Rev 1.0(93/1 1) 8.2.3. Time Format (1) Select “T ime Format” using the [ ◄ or ► ] or the [ ▲ / ▼ ] buttons and press [ENTER]. (2) T wo Time Formats are available; ‘MM/DD/YYYY’ and ‘YYYY/MM/DD’. Select a value using [ ▲ / ▼ ] buttons, and press the [EXIT] button when finished.
WDR-516S Installation Guide 24 Rev 1.0(93/1 1) 8.3. Setting Recording Condition Recording conditions under the “Quick Setup” menu tab a pply the same values to all analog channels 1~4. All settings are applied for 24 hours/day regardless of the values set for “T ime Schedule” or “Alarm Rec.
WDR-516S Installation Guide 25 Rev 1.0(93/1 1) (1) Press [MENU] button, and select “Quick Setup.” (2) Move to sub-menu by pressing [ENTER] or the [ ▼ ] button. (3) Select “Recording” using the [ ▲ / ▼ ] buttons and press the [ENTER] button.
WDR-516S Installation Guide 26 Rev 1.0(93/1 1) 8.3.5. Quality When “Recording Speed/Quality” is set as “Custom,” values can be set manually . (1) Select “Quality” using [ ▲ / ▼ ] buttons and press the [ENTER] button. (2) Select a value using the [ ◄ or ► ] button.
WDR-516S Installation Guide 27 Rev 1.0(93/1 1) 9. Connecting and Configuring Sensor 9.1. Connecting Sensor Input T o connect a sensor to S1, fix the wire to “S1” and “G“. <Note> Devices connected to the sensor input should have “Dry contact.
WDR-516S Installation Guide 28 Rev 1.0(93/1 1) 9.2. Setting Sensor at OSD menu After a sensor is connected, it can be activated through the OSD Configuration menu. Select the sensor number (S1, S2, etc.) and press the [Enter] button to configure. Use the [ ◄ or ► ] buttons to select “On” or “Off.
WDR-516S Installation Guide 29 Rev 1.0(93/1 1) 10. Connecting & Configuring Relay Out 10.1. Connecting Relay Out WDR-516S has total four ports of Relay Out. T o connect a device to “R1,” connect the wires to two “R1”s. <Note> The rated voltage and current of Relay Out are as follows.
WDR-516S Installation Guide 30 Rev 1.0(93/1 1) 10.2. Configuring Relay Out Each relay can be synchronized with a sensor input or with motion detection for each of the four time sch edules (W eekday (Day), W eekday (Night), W eekend (Day ), W eekend (Night)).
WDR-516S Installation Guide 31 Rev 1.0(93/1 1) 11. Connecting External Device with Serial Port 11.1. Connecting Text Input Device (ATM / POS / Access Control) In addition to images, the WDR-516S can record text data received from POS/A TM through the RS232 serial port.
WDR-516S Installation Guide 32 Rev 1.0(93/1 1) 12. Connecting & Configuring Serial Ports for Pan/T ilt/Zoom 12.1. Connecting Serial Port The WDR-516S has most major PTZ protocols al ready pre-programmed. Makes and models not supported can still be controlled using the T ransparen t Protocol.
WDR-516S Installation Guide 33 Rev 1.0(93/1 1) 12.2. Configuring Serial Port Configure PTZ serial ports and availabl e modes at “System / Serial Setup”. After completing serial setup, configure base addr ess and port for each channel under the “Camera” menu tab.
WDR-516S Installation Guide 34 Rev 1.0(93/1 1) <Note> Wir e Handling Trimming Wire When connecting a wire to a terminal block, follow th e instructions below . Note the different types of wire that can be used. Stranded Wir e : Peel off the wiring cover 8~10mm and solder it.
WDR-516S Installation Guide 35 Rev 1.0(93/1 1) If properly connected, the disk is recognized automatic ally as in the following picture. T o copy images, the process is as follows: Set copy range (up to 1 minute) Æ Select drive Æ Copy (press “Start”).
WDR-516S Installation Guide 36 Rev 1.0(93/1 1) 14. Connecting External Storage 14.1. IEEE1394 Bay WDR-516S has three IEEE1394 ports for external st orage device interface. W ith them, WDR-516S can expand storage capacity up to 4TB. <Note> Some IEEE1394 Bay may not be recognized by the WDR-516S.
WDR-516S Installation Guide 37 Rev 1.0(93/1 1) 14.4. Registering & Formatting HDD “Disk Manager” will automatically run on start-up after installing a HDD. If “Disk Manager” does not automatically run on star t-up, make sure the HDD is properly installed.
WDR-516S Installation Guide 38 Rev 1.0(93/1 1) (8) Select “Apply” using [ ▲ / ▼ ] button and press [EXIT] button. The HDD status is changed to “[R]” after formatting.
WDR-516S Installation Guide 39 Rev 1.0(93/1 1) 15.2. Configuring WDR-516S’s Network Information The following description is on based on Ethernet connection. For more detailed information on the Network Settings Page, please refer to “WDR-516S OSD User ’ s Guide”.
WDR-516S Installation Guide 40 Rev 1.0(93/1 1) 16. Using WDR Manager 16.1. PC System Requirements for running WDR Manager Minimal Requirements Recommended Requirements CPU P- Ⅲ 600MHz or above P- .
WDR-516S Installation Guide 41 Rev 1.0(93/1 1) (4) Select which components to install and press the “Next” button. (5) Browse and choose a directory if the default directory is not preferred. Click the “Install” button, after selecting a directory to install.
WDR-516S Installation Guide 42 Rev 1.0(93/1 1) 16.1.2. Uninstalling WDR Manager (1) Click W indows “Start” Button. (2) Select and Click ‘Uninstall’ icon to run Uninstall Shield. (3) WDR Manager program will be automatically deleted. 16.2. Configstation Click icon on desktop to run “WDR Manager Configstation” program.
WDR-516S Installation Guide 43 Rev 1.0(93/1 1) 16.3. Monitor Click the related icon and run the “WDR Manager Monitor” program. 16.4. Playback Click the related icon and run the “WDR Manager Playback” program.
WDR-516S Installation Guide 44 Rev 1.0(93/1 1) APPENDIX APPENDIX.
WDR-516S Installation Guide 45 Rev 1.0(93/1 1) Appendix #1 Installing and Replacing internal HDD Compatible HDD It is recommended to use the following HDD models with the WDR-516S. If a non-recommended HDD is used, DENTEC Corp. will not guarantee the warranty .
WDR-516S Installation Guide 46 Rev 1.0(93/1 1) <Note> The dip switch should be set at ‘MASTER’ posi tion for the first installed or built-in HDD. Additional HDD should be set as ‘SLA VE.’ Identical dip switch setting may cause system conflict or mal-function.
WDR-516S Installation Guide 47 Rev 1.0(93/1 1) (5) Fix the HDD with provided screws. Connect power and data cables to HDD Installing single HDD Installing 2 HDDs <Note> Caution for HDD Management 1. Replacing ‘SLA VE’ HDD of internal 2 HDDs cau ses permanent data loss in the SLA VE HDD.
WDR-516S Installation Guide 48 Rev 1.0(93/1 1) (8) Assemble the top cover . Registering & Formatting HDD “Disk Manager” will automatically run on start-up af ter installing a HDD. If “Disk Manager” does not automatically run on start-up, make su re the HDD is properly installed.
WDR-516S Installation Guide 49 Rev 1.0(93/1 1) (1 1) Select “Action” using [ ▲ / ▼ ] button and press [EXIT] button. (12) Select “Add” using [ ◄ or ► ] button and press [EXIT] button. (13) Select “Apply” using [ ▲ / ▼ ] button and press [EXIT] button.
WDR-516S Installation Guide 50 Rev 1.0(93/1 1) Appendix #2 Video Input Video type / impedance setup switch It’ s possible to set up Impedance of V ideo input line. When one V ideo output is connected to several Input as below , the impedance of one input should be 75 ohm.
WDR-516S Installation Guide 51 Rev 1.0(93/1 1) Appendix #3 Using CD-ROM Components of CD- ROM disc Installation Guide : WDR-516S Installation Guide User ’ s Guide : WDR-516S User ’ s Guide WDR Manager : WDR Manager User ’ s Guide ( WDR-516S Remote Management Program) Preparation T o read manual of CD-ROM disc, Adobe Acrobat 5.
WDR-516S Installation Guide 52 Rev 1.0(93/1 1) Appendix #4 Specification General CPU 32bit RISC Processor (200MIPS) Flash Memory 8MB Main Memory 64MB OS Embedded LINUX V ideo Channel 4 Analog Channel & 12 IP V ideo Channel (NTSC or P A L) Storage Device Internal 3.
WDR-516S Installation Guide 53 Rev 1.0(93/1 1) Display Monitoring Max. 120ips (Analog V ideo 60ips) ( I P V i d e o 6 0 i p s ) V iewer 1ch, 4ch, 9ch, 13ch, 16ch, Auto Sequential Playback Performance Max.
WDR-516S Installation Guide 55 Rev 1.0(93/1 1) PTZ Control Serial Port RS232(1), RS485/422(1), RS232(1) Control Method (Local) Front panel button & IR remote controller (control IP video channel a.
WDR-516S Installation Guide 55 Rev 1.0(93/1 1) Mechanical Dimension (W ⅹ D ⅹ H) 350 ⅹ 298 ⅹ 66(mm) We i g h t 3.5Kg (W ith one HDD) WDR- 516S Network Matrix DVR USB IEEE1394 A1 14 3 2 A2 A3 PW.
WDR-516S Installation Guide 56 Rev 1.0(93/1 1) Model ： W D R - 5 1 6 S Warranty ： Full 1 year as of invoice shipping date Manufacture ： DENTEC CORP. Email: tech@dentec.com.tw Address ： 8/F, No. 116 Hou-Kang St. Shih-Lin Dist, Taipei, Taiwan http://www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté DENTEC WDR-516S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du DENTEC WDR-516S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation DENTEC WDR-516S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le DENTEC WDR-516S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le DENTEC WDR-516S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du DENTEC WDR-516S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le DENTEC WDR-516S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei DENTEC WDR-516S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
