Manuel d'utilisation / d'entretien du produit 77587 du fabricant Craftsman
Aller à la page of 25
Owner's Manual CRRFTSMAN [] 6.5 Horse Power _] m 3" diameter chipping capacity CHIPPER-SHREDDER Model No. B 247.775870 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. i Sears, Roebuck and Co.
Content Page Content Page Warranty Information 2 Service & Adjustment 14 Safe Operation Practices 3 Off-Season Storage 16 Assembly 5 Trouble-Shooting 17 Operation 8 Repair Parts 18 Maintenance 11 .
This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder.
Do not ailow leaves or other debris to build-up on engine's muffler. The debris could ignite and cause a fire. Do not attempt to shred or chip material larger than specified in this manual.
Carton Contents Hopper Discharge Chute Catcher Bag __Bottle of Oii Chipper Chute • You will find the hopper in the top insert inside the carton. Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. After assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up.
ATTACHING DISCHARGE CHUTE • Remove the wing knobs from each side of the discharge opening on the chipper-shredder. See figure 3. • Using two 7/16" wrenches, remove hex lock nut, two spacers, and the hex bolt from top of the housing assembly. For easy assembly, do not remove the second spacer from the hex bolt.
to the stop washer on the inlet guide. See figure 6. ,_ WARNING: This flap control rod is a safety device to hold the flap in place inside the hopper while shredding branches. Do not operate the chipper-shredder without properly attaching this flap control rod.
I Read this owner's manual and safety rules before operating your chipper-shredder. Compare the illustration in I figure9withy_urchipper_shreddert_fami_iarizey_urselfwiththe__cati_n_fVari_usc_ntr__sandadjustments_ _1 Save this manual for future reference.
& WARNING: Before using your chipper- shredder, refer to the safety rules on pages 3 and 4 of this manual again. Always be careful. GAS AND OIL FILL-UP Oil (Packed with unit) • Only use high quality detergent oil rated with API service classification SF, SG or SH.
WARNING: Do not fill closer than 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently spilled, move chipper-shredder away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.
blades are dull and need to be sharpened or replaced. To sharpen or replace the blades, refer to Service and Adjustments section. IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in the Service and Adjustments section on page 14.
ENGINE MAINTENANCE Engine Oil • Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature. Refer to page 9 of this manual for viscosity chart.
To Service Air Cleaner: 1. Service pre-cleaner after every 25 hours of use, or at least once a season. 2. Service filter every 100 hours of use, or at least once a season. 3. Service pre-cleaner and filter more often under dusty conditions. Remove wing nut and cover.
CLEANING THE FLAIL SCREEN If the discharge area becomes clogged, remove the flail screen and clean area as follows. • Stop engine, make certain the chipper-shredder has come to a complete stop and disconnect spark plug wire from the spark plug. • Remove the two hand knobs on each side of the discharge chute.
Shredding Blade The shredding blade may be removed for sharpening or replacement as follows. • Disconnect spark plug wire and move it away from spark plug.
A WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc.
PROBLEM Engine fails to start Loss of power; operation erratic Engine overheats Too much vibration Unit does not discharge Rate of discharge slows considerably or composition of discharged material changes POSSIBLE CAUSE 1. Fuel tank empty, or stale fuel 2.
SEARS CRAFTSMAN 6.5 H.P. CHIPPER-SHREDDER MODEL 247.775870 29 ,/62 66 8 13 17 48 64 42 42 j 'i 53 58 18.
SEARS CRAFTSMAN 6.5 H.P. CHIPPER-SHREDDER MODEL 247.775870 Key No 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Pe_ No 770-1231A _11480 681-0111 6.
SEARS CRAFTSMAN 6,5 H.P. ENGINE MODEL 143.986501 FOR CHIPPER-SHREDDER MODEL 247.775870 310 -- 279 161A 307 I 305 161 308 159 4O 41 / s 82 182 185 / 184 _ • 154 155 173 }--43 130A _207 252 130 135 6.
SEARS CRAFTSMAN 6.5 H.P. ENGINE MODEL 143.986501 FOR CHIPPER-SHREDDER MODEL 247.775870 65 60 341 lOO 342 25A 292 110 313 26 £0 370A 261 261A I 260 390 287 / O / 327 21.
SEARS CRAFTSMAN 6.5 H.P. ENGINE MODEL 143.986501 FOR CHIPPER-SHREDDER MODEL 247.775870 Key No. Part No. Description Key No. Part No. Description 1 2 4 5 14 15 16 19 2O 25 25A 26 30 35 37 38 40 41 42 4.
SEARS CRAFTSMAN 6.5 H.P. ENGINE MODEL 143.986501 FOR CHIPPER-SHREDDER MODEL 247.775870 Key Pad No. No. 305 35554 307 35499 308 37079 310 36902 313 34080 325 29443 327 35392 341 36644 342 651010 Descri_ion Key Part No.
SEARS CRAFTSMAN 6.5 H.P. ENGINE MODEL 143,986501 FOR CHIPPER-SHREDDER MODEL 247.775870 Recoil Starter O O Key Part Description No. No. 590736 1 590599A 2 590600 3 590696 4 590601 5 590697 6 590698 7 5.
For the repair or replacement parts you need delivered directly to yourhome Call 7 am - 7 prn, 7 days a week 1-800-366-PART (1-800-366-7278) For in-homemajor brand repair service Call 24 hours a day, .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 77587 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 77587 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 77587, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 77587 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 77587, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 77587.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 77587. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 77587 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
