


fuses removed from the holder), earth leakage trips and contactors. • The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening width of minimum 3 mm.

1 Induction cooking zone 2 Control panel
180 mm · 180 mm 1


Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which functions operate.

1 ON / OFF To activate and deactivate the hob.
To show for which zone you set the time.
8 / - To increase or decrease the time.
10 Power function To activate and deactivate the function.
The cooking zone is deactivated.
Display Description

- The cooking zone operates.
STOP+GO function operates.
Power function operates.
+ digit There is a malfunction.
A cooking zone is still hot (residual heat).
Lock / The Child Safety Device function operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off function operates.
the bottom of the cookware. The glass ceramic is heated by the heat of the cookware.
The induction cooking zones make the heat necessary for cooking process directly in
Touch for 1 second to activate or deactivate the hob.
comes on and the hob deactivates. The relation between the heat setting and the time after which the hob deactivates:
The function deactivates the hob automatically if:
Heat setting The hob deacti- vates after
, 1 - 2 6 hours
Display Description · 5 4 hours

remaining time counts back to 00. The indicator of the cooking zone goes out.
Touch to increase the heat setting. Touch to decrease the heat setting. Touch and at the same time to deactivate the cooking zone.
When the time comes to an end, the sound operates and 00 flashes. The cooking zone deactivates.
To stop the sound: touch .
This function makes more power available to the induction cooking zones. The function can be activated for the induction cooking zone only for a limited period of time. After this time the induction cooking zone automatically sets back to the highest heat setting.
Minute Minder You can use this function as a Minute Minder when the hob is activated and the cooking zones do not operate (the heat setting display shows ).
To activate the function: touch . Touch or of the timer to set the time. When the time comes to an end, the sound operates and 00 flashes.
Refer to “Technical information” chapter.
To activate the function for a cooking zone: touch . comes on.
To stop the sound: touch .
The function has no effect on the operation of the cooking zones.
To deactivate the function: touch or .
STOP+GO
Count Down Timer You can use this function to set how long the cooking zone should operate for a single cooking session.
This function sets all cooking zones that operate to the lowest heat setting.
When the function operates, you cannot change the heat setting.
First set the cooking zone then set the function. You can set the heat setting before or after you set the function.
The function does not stop the timer functions.
To set the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on.
To activate the function: touch . comes on.
To deactivate the function: touch . The previous heat setting comes on.
To activate the function or change the time: touch or of the timer to set the time (00 - 99 minutes). When the indicator of the cooking zone starts to flash slowly the time counts down.
You can lock the control panel while cooking zones operate. It prevents an accidental change of the heat setting.
To see the remaining time: set the cooking zone with . The indicator of the cooking zone starts to flash quickly. The display shows the remaining time.
Set the heat setting first.
To activate the function: touch . comes on for 4 seconds. The Timer stays on.

To deactivate the function: touch . The previous heat setting comes on.
When you deactivate the hob, you also deactivate this function.
If there is a problem with electrical supply and the hob deactivates it does not keep previous settings.
This function prevents an accidental operation of the hob.
To activate the function: activate the hob with . Do not set the heat setting. Touch for 4 seconds. comes on. Deactivate the hob with .
To deactivate the function: activate the hob with . Do not set the heat setting. Touch for 4 seconds. comes on. Deactivate the hob with .
To override the function for only one cooking time: activate the hob with . comes on. Touch for 4 seconds. Set the heat setting in 10 seconds. You can operate the hob. When you deactivate the hob with the function operates again.
Originally the sounds are activated.

receives only a part of the power generated by the cooking zone.
For induction cooking zones a strong electro-magnetic field creates the heat in the cookware very quickly.
Refer to “Technical information” chapter.
Use the induction cooking zones with correct cookware.
If you can hear:
The bottom of the cookware must be as thick and flat as possible.
The relation between the heat setting and the cooking zone consumption of power is not linear. When you increase the heat setting, it is not proportional to the increase of the cooking zone consumption of power. It means that the cooking zone with the medium heat setting uses less than a half of its power.
Induction cooking zones adapt to the dimension of the bottom of the cookware automatically to some limit.
The cooking zone efficiency is related to the diameter of the cookware. The cookware with a smaller diameter than the minimum
The data in the table is for guidance only.
- 1 Keep cooked food warm. as neces- sary
Put a lid on the cookware.
Cookware material · Cookware dimensions

Turn halfway through.
9 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. Power function is activated.
the dirt can cause damage to the hob. Put the special scraper on the glass surface at an acute angle and move the blade on the surface. • Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and some detergent. After cleaning, rub the hob dry with a soft cloth.
as neces- sary

What to do if...
Problem Possible cause Remedy
You cannot activate or oper- ate the hob.
The hob is not connected to an electrical supply or it is connected incorrectly.
Check if the hob is correctly connected to the electrical supply. Refer to the connec- tion diagram.
The fuse is released. Make sure that the fuse is the cause of the malfunction. If the fuse releases again and again, contact a qualified electrician.
Activate the hob again and set the heat setting in less than 10 seconds.
You touched 2 or more sen- sor fields at the same time.
Touch only one sensor field.
STOP+GO function operates. Refer to "Daily use" chapter.
There is water or fat stains on the control panel.
Clean the control panel.
An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated.
You put something on one or more sensor fields.
Remove the object from the sensor fields.
The hob deactivates. You put something on the
Remove the object from the sensor field.
sensor field .
Residual heat indicator does not come on.
The zone is not hot because it operated only for a short time.
If the zone operated suffi- ciently long to be hot, speak to an Authorised Service Centre.
The heat setting changes be- tween two levels.
Power management function operates.
Refer to "Daily use" chapter.
The sensor fields become hot.
The cookware is too large or you put it too near to the controls.
Put large cookware on the rear zones if possible.
There is no signal when you touch the panel sensor fields.
The signals are deactivated. Activate the signals. Refer to "Daily use" chapter.
comes on. Automatic Switch Off oper- ates.
Deactivate the hob and acti- vate it again.
comes on. The Child Safety Device or the Lock function operates.
Refer to "Daily use" chapter.

Problem Possible cause Remedy
comes on. There is no cookware on the zone.
Put cookware on the zone.
The cookware is incorrect. Use the correct cookware. Refer to “Hints and tips” chapter.
The diameter of the bottom of the cookware is too small for the zone.
Use cookware with correct dimensions. Refer to “Technical informa- tion” chapter.
and a number come on. There is an error in the hob. Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again.
If comes on again, speak to an Authorised Service Centre.
comes on. There is an error in the hob because a cookware boils dry. Automatic Switch Off and the overheating protec- tion for the zones operate.
Deactivate the hob. Remove the hot cookware. After ap- proximately 30 seconds, acti- vate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware become sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter.
If you cannot find a solution...
servicing by a service technician or dealer will not be free of charge, also during the warranty period. The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet.
If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Give also three digit letter code for the glass ceramic (it is in the corner of the glass surface) and an error message that comes on. Make sure, you operated the hob correctly. If not the

Stick the adhesive labels as indicated below:
MOD.
MOD.
MOD. PROD.NO. SER.NO.
PROD.NO.
PROD.NO.
SER.NO
03 IT
DATA
DATA
MADE IN ITALY
A) Stick it on Guarantee Card and send
C) Stick it on instruction booklet.
this part (if applicable). B) Stick it on Guarantee Card and keep
this part (if applicable).
and work surfaces that align to the standards.
Before the installation
Before you install the hob, write down the information bellow from the rating plate. The rating plate is on the bottom of the hob.
Model PNC Serial number
Only use the built-in hobs after you assemble the hob into correct built-in units

edge of the glass ceramic. Do not extend it. Make sure that the ends of the seal stripe are located in the middle of one side of the hob. 3. Add some mm when you cut the seal stripe to the length.





If several 30 cm hobs are to be installed side by side into the same cut out, an assembly kit including a support side bracket and supplementary seals is available at our Authorised Service Centres. The relevant installation instructions are supplied within the kit package.


Cooking zone Nominal pow- er (maximum heat setting) [W]
Power func- tion maximum duration [min]
Middle front 1800 2500 10 145 - 180
Middle rear 1800 2500 10 145 - 180
The power of the cooking zones can be different in some small range from the data in the table. It changes with the material and dimensions of the cookware.
For optimal cooking results use cookware not larger than the diameter in the table.
Type of hob Built-In Hob
Number of cooking zones 2
Diameter of circular cooking zones (Ø)
Middle front Middle rear
18.0 cm 18.0 cm
Energy consumption per cooking zone (EC electric cooking)
Middle front Middle rear
182.5 Wh / kg 182.5 Wh / kg
Energy consumption of the hob (EC electric hob)
182.5 Wh / kg
EN 60350-2 - Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance
You can save energy during everyday cooking if you follow below hints.

dispose appliances marked with the symbol
Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not
with the household waste. Return the product to your local recycling facility or contact your municipal office.
Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| You cannot activate or oper- ate the hob. | The hob is not connected to an electrical supply or it is connected incorrectly. | Check if the hob is correctly connected to the electrical supply. Refer to the connec- tion diagram. | p.11 |
| You cannot activate or oper- ate the hob. | The fuse is released. | Make sure that the fuse is the cause of the malfunction. If the fuse releases again and again, contact a qualified electrician. | p.11 |
| You cannot activate or oper- ate the hob. | Activate the hob again and set the heat setting in less than 10 seconds. | p.11 | |
| You cannot activate or oper- ate the hob. | You touched 2 or more sen- sor fields at the same time. | Touch only one sensor field. | p.11 |
| You cannot activate or oper- ate the hob. | STOP+GO function operates. | Refer to "Daily use" chapter. | p.11 |
| You cannot activate or oper- ate the hob. | There is water or fat stains on the control panel. | Clean the control panel. | p.11 |
| An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated. | You put something on one or more sensor fields. | Remove the object from the sensor fields. | p.11 |
| The hob deactivates. | You put something on the sensor field . | Remove the object from the sensor field. | p.11 |
| Residual heat indicator does not come on. | The zone is not hot because it operated only for a short time. | If the zone operated suffi- ciently long to be hot, speak to an Authorised Service Centre. | p.11 |
| The heat setting changes be- tween two levels. | Power management function operates. | Refer to "Daily use" chapter. | p.11 |
| The sensor fields become hot. | The cookware is too large or you put it too near to the controls. | Put large cookware on the rear zones if possible. | p.11 |
| There is no signal when you touch the panel sensor fields. | The signals are deactivated. | Activate the signals. Refer to "Daily use" chapter. | p.11 |
| comes on. | Automatic Switch Off oper- ates. | Deactivate the hob and acti- vate it again. | p.11 |
| comes on. | The Child Safety Device or the Lock function operates. | Refer to "Daily use" chapter. | p.11 |
| comes on. | There is no cookware on the zone. | Put cookware on the zone. | p.12 |
| comes on. | The cookware is incorrect. | Use the correct cookware. Refer to “Hints and tips” chapter. | p.12 |
| comes on. | The diameter of the bottom of the cookware is too small for the zone. | Use cookware with correct dimensions. Refer to “Technical informa- tion” chapter. | p.12 |
| and a number come on. | There is an error in the hob. | Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again. If comes on again, speak to an Authorised Service Centre. | p.12 |
| comes on. | There is an error in the hob because a cookware boils dry. Automatic Switch Off and the overheating protec- tion for the zones operate. | Deactivate the hob. Remove the hot cookware. After ap- proximately 30 seconds, acti- vate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware become sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter. | p.12 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.