FR
Constructa logo
Notice d'utilisation officielle

Constructa CA424252

56 pages·1.7 MB·Plaque à induction·PDF·ENITJA
Constructa CA424252
Table des matières 225 sections Ú Table of contents[en] Instruction manual · Produktinfo · Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com · : Safety precautions · … AfficherMasquer
Ú Table of contents[en] Instruction manualp.1Produktinfop.1Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.comp.1: Safety precautionsp.1Please read this manual carefully. Please keep the instruction and installation manual as well as the appliance certificate in a safe place for later use or for subsequent owners.p.1Check the appliance after removing it from the packaging. If it has suffered any damage in transport, do not connect the appliance, contact the Technical Assistance Service and provide written notification of the damage caused, otherwise you will los...p.1This appliance must be installed according to the installation instructions included.p.1This appliance is intended for domestic use only. The appliance must only be used for the preparation of food and drink. The appliance must be supervised during operation. Only use this appliance indoors.p.1Do not use covers. These can cause accidents, due to overheating, catching fire or materials shattering, for example.p.1Do not use inappropriate child safety shields or hob guards. These can cause accidents.p.1This appliance is not intended for operation with an external clock timer or a remote control.p.1This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...p.1Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.p.1Keep children below the age of 8 years old at a safe distance from the appliance and power cable.p.1We advise that you exercise caution using or standing near an induction hob while it is in operation, if you wear a pacemaker or a similar medical device. Consult your doctor or the device manufacturer concenring its conformity or any possible incomp...p.1Risk of fire!p.2■ Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.p.2■ The hotplates become very hot. Never place combustible items on the hob. Never place objects on the hob.p.2■ The appliance gets hot. Do not keep combustible objects or aerosol cans in drawers directly underneath the hob.p.2■ The hob switches off automatically and can no longer be operated. It may switch on unintentionally at a later point. Switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2Risk of burns!p.2■ The hotplates and surrounding area (particularly the hob surround, if fitted) become very hot. Never touch the hot surfaces. Keep children at a safe distance.p.2■ The hotplate heats up but the display does not work. Switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2■ Metal objects on the hob quickly become very hot. Never place metal objects (such as knives, forks, spoons and lids) on the hob.p.2■ After each use, always turn off the hob at the main switch. Do not wait until the hob turns off automatically after the pan is removed.p.2Risk of electric shock!p.2■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...p.2■ Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.p.2■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2■ Cracks or fractures in the glass ceramic may cause electric shocks. Switch off the circuit breaker in the fuse box. Contact the after-sales service.p.2Malfunction risk!p.2The hob is equipped with a fan in the lower section. If there is a drawer under the hob it should not be used to store small objects or paper, since they could damage the fan or interfere with the cooling if they are sucked into it.p.2There should be a minimum of 2 cm between the contents of the drawer and fan intake.p.2Risk of injury!p.2■ When cooking in a bain marie, the hob and cooking container could shatter due to overheating. The cooking container in the bain marie must not directly touch the bottom of the water-filled pot. Only use heat-resistant cookware.p.2■ Saucepans may suddenly jump due to liquid between the pan base and the hotplate. Always keep the hotplate and saucepan bases dry.p.2Elements that may damage the appliancep.2Caution!p.2■ Rough pan bases may scratch the hob.p.2■ Avoid leaving empty pots and pans on the hotplate. Doing so may cause damage.p.2■ Do not place hot pans on the control panel, the indicator area, or the hob frame. Doing so may cause damage.p.2■ Hard or pointed objects dropped on the hob may damage it.p.2Overviewp.3The following table presents the most common damage caused:p.3Protecting the environmentp.3Environmentally-friendly disposalp.3Dispose of packaging in an environmentally-friendly manner.p.3Energy-saving advicep.3■ Use pans with flat bases. Bases that are not flat use a lot more energy.p.3■ The diameter of the pan base must match the size of the hotplate. Please note: pan manufacturers usually provide the diameter for the top of the pan, which is usually larger than the diameter of the pan base.p.3■ Use a small pan for small amounts of food. A large pan which is not full uses a lot of energy.p.3■ Use little water when cooking. This saves energy and preserves all the vitamins and minerals in vegetables.p.3Induction cookingp.3Advantages of induction cookingp.3Induction cooking represents a radical change from the traditional method of heating; the heat is generated directly in the pan. It therefore offers a number of advantages:p.3■ Energy is saved.p.3■ Care and cleaning are simpler. Foods that have spilt do not burn as quickly.p.3Cookwarep.3Only ferromagnetic pans are suitable for induction cooking; these may be made from:p.3■ cast ironp.3To determine whether a pan is suitable, check to see if a magnet will stick to its base.p.3There are other types of cookware for induction whose base is not entirely ferromagnetic.p.3Unsuitable pansp.3Never use diffuser hobs or pans made from:p.3■ glassp.3■ earthenwarep.3■ copperp.3Characteristics of the pan basep.4The characteristics of the pan base may affect the uniformity of the cooking results. Pans made from materials which help diffuse heat, such as stainless steel sandwich pans, distribute heat uniformly, saving time and energy.p.4Absence of pan or unsuitable sizep.4If no pan is placed on the selected hotplate, or if it is made of unsuitable material or is not the correct size, the power level displayed on the hotplate indicator will flash. Place a suitable pan on the hotplate to stop the flashing. If this takes...p.4Empty pans or those with a thin basep.4Do not heat empty pans, nor use pans with a thin base. The hob is equipped with an internal safety system. However, an empty pan may heat up so quickly that the "automatic switch off" function may not have time to react and the pan may reach very hig...p.4Pan detectionp.4Each hotplate has a minimum limit for detecting pans, which varies depending on the material of the pan being used. You should therefore use the hotplate that is most suitable for the diameter of your pan.p.4Getting to know your appliancep.4On page 2, you will find information on the dimensions and power of the hotplates.p.4The control panelp.4Control panelsp.4Pressing a symbol activates its corresponding function.p.4Notep.4The hotplatesp.4Residual heat indicatorp.4The hob has a residual heat indicator for each hotplate to show those which are still hot. Avoid touching them when this indicator is lit.p.4Although the hob is switched off, the indicator œ or • will remain on for as long as the hotplate is hot.p.4If the pan is removed before the hotplate is turned off, the indicator œ or • and the selected power level will appear alternately.p.4Programming the hobp.5This section will show you how to program the hotplates. The table contains power levels and cooking times for several dishes.p.5Turning the hob on and offp.5The hob is turned on and off using the main switch.p.5To turn on: Press the # symbol. A beep sounds. The indicator located next to the main switch and the ‹ indicators of the hotplates light up. The hob is ready for use.p.5To turn off: press the # symbol until the indicators go out. All hotplates are turned off. The residual heat indicator will remain lit until the hotplates have cooled down sufficiently.p.5Notesp.5Set the hotplatep.5Select the required power level with the + and - symbols.p.5Power level 1 = minimum power.p.5Power level 9 = maximum power.p.5Each power level has an intermediate setting. This is marked with a dot.p.5Selecting the hotplate and the power levelp.5The hob must be switched on.p.51. Select the hotplate with the $ symbol.p.52. Within the next 10 seconds press the + or - symbol. The basic setting appears:p.5+ symbol = power level 9p.5- symbol = power level 4p.5Changing the power levelp.5Select the hotplate and press the + or - symbol until the required power level comes on.p.5To switch off the hotplatep.5Select the hotplate and then press the + or - symbol until ‹ symbol appears.p.5The hotplate turns off and the residual heat indicator appears.p.5Notesp.5Cooking guidelines tablep.5The table below contains some examples.p.5Cooking times depend on the power level, type, weight and quality of the food. As such they are approximate.p.5When heating purées, creams and thick sauces, stir occasionally.p.5Use power level 9 to begin cooking.p.5Childproof lockp.7The hob can be protected against being accidentally turned on, to ensure that children do not switch on the hotplates.p.7Activating and deactivating the childproof lockp.7The hob should be turned off.p.7To activate: press the symbol ‚ for approximately 4 seconds. The indicator next to the symbol ‚ lights up for 10 seconds. The hob is locked.p.7To deactivate: press the symbol ‚ for approximately 4 seconds. The lock is now deactivated.p.7Childproof lockp.7With this function, the childproof lock automatically activates when a hob is switched off.p.7Activating and deactivatingp.7All of the relevant information on the automatic childproof lock connection can be found in the Basic settings chapter.p.7Powerboost functionp.7The Powerboost function can be used to heat large amounts of water more quickly than the power level Š.p.7Restrictions when usingp.7This function is available for all hotplates, provided that the other zone of the same group is not operating (see image). Otherwise, in the visual display of the selected hotplate › and Š will flash; then the power level will automatically set it...p.7To activatep.71. Select a hotplate.p.72. Press the › symbol.p.7To deactivatep.71. Select a hotplate.p.72. Press the › symbol.p.7Notep.7Time program functionp.7This function may be used in two different ways:p.7Turning off a hotplate automaticallyp.7The hotplate turns off automatically once the selected time has elapsed.p.7Program the cooking time.p.71. Select the desired hotplate and power level.p.72. Press the 3 symbol. The Ú indicator on the hotplate lights up. ‹‹ is displayed on the time program function display.p.73. Press the + or - symbol. The basic setting appears:p.7+ symbol: 30 minutes.p.7- symbol: 10 minutes.p.74. Press the + or - symbol until the required cooking time appears.p.7Notep.7Changing or cancelling the timep.8Selecting the hotplate . Press the 3 symbol and change the cooking time with the + or - symbols, or set to ‹‹.p.8Once the time has elapsedp.8The hotplate switches off. A beep sounds and in the time program function display ‹‹ appears for 10 seconds. The Ú indicator on the hotplate lights up. Pressing the 3 symbol turns off the indicators and stops the beeping.p.8Notesp.8The timerp.8The timer can be set for periods of up to 99 minutes. It is independent of the other settings. This function does not automatically switch off a hotplate.p.8How to programp.81. The timer can be selected in two different ways:p.82. Press the + or - symbol. The basic setting appears.p.8+ symbol: 10 minutes.p.83. Set the desired time using the + or - symbols.p.8Changing or cancelling the timep.8Press the 3 symbol various times until the Ú indicator next to the W symbol lights up. Change the time or set to ‹‹ with the + or - symbols.p.8Once the time has elapsedp.8A warning signal sounds. ‹‹ is displayed on the time program function display. After 10 seconds the indicators turn off.p.8Pressing the 3 symbol turns off the indicators and stops the beeping.p.8Automatic time limitationp.8If the hotplate remains in use for a long time and no changes are made in the settings, the automatic time limitation function is triggered.p.8The hotplate stops heating. The ”, ‰ symbol and the residual heat indicator œ/• flash alternately in the display.p.8The indicator goes out when any symbol is pressed. The hotplate can now be reset.p.8When the automatic time function is used, it is governed by the selected power level (from 1 to 10 hours).p.8Basic settingsp.8The device has several basic settings. These settings may be adapted to the user's individual needs.p.8Accessing the basic settingsp.9The hob should be turned off.p.91. Switch on the hob.p.92. Within the next 10 seconds, press the ‚ symbol for 4 seconds.p.93. Press the ‚ symbol several times until the required function indicator appears.p.94. Next select the desired setting using the + and - symbols.p.95. Press the ‚ symbol again for more than 4 seconds.p.9Quitp.9To leave the basic settings, turn off the hob at the main switch.p.9Care and cleaningp.9The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible conditionp.9Hobp.9Cleaningp.9Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clean it.p.9Only use cleaning products specifically designed for hobs. Follow the instructions provided on the packaging.p.9Do not use:p.9■ Dishwasher detergentp.9■ Abrasive productsp.9■ Corrosive products such as oven sprays or stain removersp.9■ Sponges that may scratchp.9The best way to remove stubborn stains is to use a glass scraper. Follow the manufacturer's instructions.p.9Suitable glass scrapers can be obtained through the Technical Assistance Service or from our online shop.p.9Hob framep.9In order to avoid damage to the hob frame, follow the indications below:p.9■ Do not use sharp or abrasive productsp.9Fixing malfunctionsp.10Malfunctions are usually due to small details. Before calling the Technical Assistance Service you should bear in mind the following advice and warnings.p.10Normal noise while the appliance is workingp.10Induction heating technology is based on the creation of electromagnetic fields that generate heat directly at the base of the pan. Depending on how the pan has been manufactured, certain noises or vibrations may be produced such as those described b...p.10A deep humming sound as in a transformerp.10This noise is produced when cooking with a high power level. It is caused by the amount of energy transferred from the hob to the pan. The noise disappears or becomes faint when the power level is lowered.p.10A low whistling soundp.10This noise is produced when the pan is empty. The noise disappears when water or food is added to the pan.p.10A crackling soundp.10This noise occurs in pans which are made from different materials superimposed on one another. It is caused by the vibrations that occur in the adjoining surfaces of the different superimposed materials. The noise comes from the pan. The amount of fo...p.10A high-pitched whistling soundp.10This noise is produced mainly in pans made from different materials superimposed on one another, and it occurs when such pans are heated at maximum power on two hotplates at the same time. The whistling disappears or becomes fainter as soon as the po...p.10Noise from the fanp.10For proper use of the electronic system, the temperature of the hob must be controlled. To do this, the hob has a fan which turns on when a high temperature is detected. The fan may also work by inertia after the hob has been switched off, if the tem...p.10The noises described are normal, they are part of induction heating technology and not a sign of malfunction.p.10After-sales servicep.11Our after-sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call-out.p.11E number and FD number:p.11Please quote the E number (product number) and the FD number (production number) of your appliance when contacting the after-sales service. The rating plate bearing these numbers can be found on the appliance certificate.p.11Please note that a visit from an after-sales service engineer is not free of charge, even during the warranty period.p.11Please find the contact data of all countries in the enclosed customer service list.p.11Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.p.11Tested dishesp.11This table has been prepared for assessment institutions to provide controls for our appliances.p.11The table data refers to our Schulte-Ufer cookware accessories (4-piece cookware set for the CZ9442X0 induction hob) with the following dimensions:p.11■ Pot: 16 cm Ø, 1.7 l, for 14.5 cm Ø hotplatesp.11■ Pot: 22 cm Ø, 4.2 l, for 18 cm Ø hotplatesp.11Ø 14.5 cmp.11
Page 1 of the Constructa CA424252 user manual — : Safety precautions
Page 1 · cliquer pour agrandir
Page 1

Ú Table of contents [en]Instruction manual

Safety precautions 29 Elements that may damage the appliance 30 Protecting the environment 31 Environmentally-friendly disposal 31 Energy-saving advice 31 Induction cooking 31 Advantages of induction cooking 31 Cookware 31 Getting to know your appliance 32 The control panel 32 The hotplates 32 Residual heat indicator 32 Programming the hob 33 Turning the hob on and off 33 Set the hotplate 33 Cooking guidelines table 33 Childproof lock 35 Activating and deactivating the childproof lock 35 Childproof lock 35 Powerboost function 35 Restrictions when using 35

To activate 35 To deactivate 35 Time program function 35 Turning off a hotplate automatically 35 The timer 36 Automatic time limitation 36 Basic settings 36 Accessing the basic settings 37 Care and cleaning 37 Hob 37 Hob frame 37 Fixing malfunctions 38 Normal noise while the appliance is working 38 After-sales service 39 Tested dishes 39

Produktinfo

Additional information on products, accessories, replacement parts and services can be found at www.constructa.de and in the online shop www.constructa-eshop.com

: Safety precautions

Please read this manual carefully. Please keep the instruction and installation manual as well as the appliance certificate in a safe place for later use or for subsequent owners. Check the appliance after removing it from the packaging. If it has suffered any damage in transport, do not connect the appliance, contact the Technical Assistance Service and provide written notification of the damage caused, otherwise you will lose your right to any type of compensation. This appliance must be installed according to the installation instructions included. This appliance is intended for domestic use only. The appliance must only be used for the preparation of food and drink. The appliance must be supervised during operation. Only use this appliance indoors. Do not use covers. These can cause accidents, due to overheating, catching fire or materials shattering, for example. Do not use inappropriate child safety shields or hob guards. These can cause accidents.

This appliance is not intended for operation with an external clock timer or a remote control. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards. Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. We advise that you exercise caution using or standing near an induction hob while it is in operation, if you wear a pacemaker or a similar medical device. Consult your doctor or the device manufacturer concenring its conformity or any possible incompatibilities,

Page 2 of the Constructa CA424252 user manual — Elements that may damage the appliance
Page 2 · cliquer pour agrandir
Page 2

Risk of fire!

  • Do not use any high-pressure cleaners or

steam cleaners, which can result in an electric shock.

  • Hot oil and fat can ignite very quickly.

Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar.

Risk of electric shock! ■ A defective appliance may cause electric

shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of fire! ■ The hotplates become very hot. Never

place combustible items on the hob. Never place objects on the hob.

Risk of electric shock! ■ Cracks or fractures in the glass ceramic

may cause electric shocks. Switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of fire! ■ The appliance gets hot. Do not keep

combustible objects or aerosol cans in drawers directly underneath the hob.

Risk of fire! ■ The hob switches off automatically and

Malfunction risk! The hob is equipped with a fan in the lower section. If there is a drawer under the hob it should not be used to store small objects or paper, since they could damage the fan or interfere with the cooling if they are sucked into it. There should be a minimum of 2 cm between the contents of the drawer and fan intake.

can no longer be operated. It may switch on unintentionally at a later point. Switch off the circuit breaker in the fuse box. Contact the after-sales service.

Risk of burns!

  • The hotplates and surrounding area

(particularly the hob surround, if fitted) become very hot. Never touch the hot surfaces. Keep children at a safe distance.

Risk of burns! ■ The hotplate heats up but the display does

Risk of injury!

not work. Switch off the circuit breaker in the fuse box. Contact the after-sales service.

  • When cooking in a bain marie, the hob

and cooking container could shatter due to overheating. The cooking container in the bain marie must not directly touch the bottom of the water-filled pot. Only use heat-resistant cookware.

Risk of burns! ■ Metal objects on the hob quickly become

very hot. Never place metal objects (such as knives, forks, spoons and lids) on the hob.

Risk of injury! ■ Saucepans may suddenly jump due to

Risk of fire!! ■After each use, always turn off the hob at

liquid between the pan base and the hotplate. Always keep the hotplate and saucepan bases dry.

the main switch. Do not wait until the hob turns off automatically after the pan is removed.

Elements that may damage the appliance

Risk of electric shock!

  • Incorrect repairs are dangerous. Repairs

may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

  • Rough pan bases may scratch the hob.
  • Avoid leaving empty pots and pans on the hotplate. Doing so

may cause damage.

  • Do not place hot pans on the control panel, the indicator

area, or the hob frame. Doing so may cause damage.

  • Hard or pointed objects dropped on the hob may damage it.
  • Aluminium foil and plastic containers will melt if placed on the

hotplate while it is hot. The use of laminated sheeting is not recommended on the hob.

Risk of electric shock!

Page 3 of the Constructa CA424252 user manual — Cookware
Page 3 · cliquer pour agrandir
Page 3

The following table presents the most common damage caused:

Stains Food spillage Immediately remove spilt food using a glass scraper.

Unsuitable cleaning products Only use cleaning products specifically designed for glass-ceramic hobs.

Scratches Salt, sugar and sand Do not use the hob as a tray or working surface.

Pans with rough bottoms may scratch the glass ceramic

Check pans.

Fading Unsuitable cleaning products Only use cleaning products specifically produced for glass-ceramic hobs.

Contact with pans Lift pots and pans before moving them around.

Chips Sugar, substances with a high sugar content

Immediately remove spilt food using a glass scraper.

Protecting the environment

Environmentally-friendly disposal

  • Use pans with flat bases. Bases that are not flat use a lot

more energy.

Dispose of packaging in an environmentally-friendly manner.

  • The diameter of the pan base must match the size of the

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

hotplate. Please note: pan manufacturers usually provide the diameter for the top of the pan, which is usually larger than the diameter of the pan base.

  • Use a small pan for small amounts of food. A large pan which

is not full uses a lot of energy.

  • Use little water when cooking. This saves energy and

preserves all the vitamins and minerals in vegetables.

Energy-saving advice

  • Select the lowest power level to maintain cooking. If the

power level is too high, energy is wasted.

  • Always use the correct lid for each pan. Cooking without a lid

uses a lot more energy. Use a glass lid to provide visibility and avoid having to lift the lid.

Induction cooking

Advantages of induction cooking

There are other types of cookware for induction whose base is not entirely ferromagnetic.

Induction cooking represents a radical change from the traditional method of heating; the heat is generated directly in the pan. It therefore offers a number of advantages:

Constructa CA424252 — Advantages of induction cooking diagram (page 3)
Fig. 1 · Advantages of induction cooking

When using large cookware on a smaller ferromagnetic area, only the ferromagnetic zone heats up, so heat might not be uniformly distributed.

  • Time savings for cooking and frying; since the pan is heated

directly.

  • Energy is saved.

Pans with aluminium areas inserted in the base reduce the ferromagnetic area, so less heat may be supplied and the pan may be difficult to detect or not be detected at all.

  • Care and cleaning are simpler. Foods that have spilt do not

burn as quickly.

  • Heat and safety control; the hob supplies or cuts off power as

soon as the control knob is turned on. The induction hotplate stops supplying heat if the pan is removed without having previously switched it off.

For good cooking results, the diameter of the cookware's ferro- magnetic area should match the size of the hotplate. If cookware is not detected on a hotplate, try it on the next smaller hotplate down.

Cookware

Only ferromagnetic pans are suitable for induction cooking; these may be made from:

  • enamelled steel
  • cast iron
  • special stainless steel induction pans.

Never use diffuser hobs or pans made from:

  • common thin steel

To determine whether a pan is suitable, check to see if a magnet will stick to its base.

  • glass
  • earthenware
  • copper
  • aluminium

Overview · Damage Cause Measure · Unsuitable pans

Page 4 of the Constructa CA424252 user manual — Residual heat indicator
Page 4 · cliquer pour agrandir
Page 4

Characteristics of the pan base

Empty pans or those with a thin base

The characteristics of the pan base may affect the uniformity of the cooking results. Pans made from materials which help diffuse heat, such as stainless steel sandwich pans, distribute heat uniformly, saving time and energy.

Do not heat empty pans, nor use pans with a thin base. The hob is equipped with an internal safety system. However, an empty pan may heat up so quickly that the "automatic switch off" function may not have time to react and the pan may reach very high temperatures. The base of the pan could melt and damage the glass on the hob. In this case, do not touch the pan and switch the hotplate off. If it fails to work after it has cooled down, please contact the Technical Assistance Service.

Absence of pan or unsuitable size

If no pan is placed on the selected hotplate, or if it is made of unsuitable material or is not the correct size, the power level displayed on the hotplate indicator will flash. Place a suitable pan on the hotplate to stop the flashing. If this takes more than 90 seconds, the hotplate will switch off automatically.

Each hotplate has a minimum limit for detecting pans, which varies depending on the material of the pan being used. You should therefore use the hotplate that is most suitable for the diameter of your pan.

Getting to know your appliance

On page 2, you will find information on the dimensions and power of the hotplates.

The control panel

$ Selecting the hotplate

‚-Š Power levels

A/@ Selecting settings

  • / œ Residual heat

3 Time program function

‹‹ Time program function

Pressing a symbol activates its corresponding function.

The hotplates

Hotplate Activating and deactivating

$ Single hotplate Use correctly-sized cookware.

æ/î Grill zone The zone switches on automatically when a pan whose base is the same size as its outer area is placed on it.

Only use cookware suitable for induction cooking; see the "Appropriate cookware" section.

Residual heat indicator

Although the hob is switched off, the indicator œ or • will remain on for as long as the hotplate is hot.

The hob has a residual heat indicator for each hotplate to show those which are still hot. Avoid touching them when this indicator is lit.

If the pan is removed before the hotplate is turned off, the indicator œ or • and the selected power level will appear alternately.

Show 9 more labels / short text on this page
Pan detection · Control panels · Indicators · # Main switch · ‹ Functionality · › Powerboost function · › Powerboost function · ‚ Childproof lock · Control panels
Page 5 of the Constructa CA424252 user manual — Cooking guidelines table
Page 5 · cliquer pour agrandir
Page 5

Programming the hob

This section will show you how to program the hotplates. The table contains power levels and cooking times for several dishes.

2. Within the next 10 seconds press the + or - symbol. The basic setting appears: + symbol = power level 9 - symbol = power level 4

Turning the hob on and off

The hob is turned on and off using the main switch.

To turn on: Press the # symbol. A beep sounds. The indicator located next to the main switch and the ‹ indicators of the hotplates light up. The hob is ready for use.

To turn off: press the # symbol until the indicators go out. All hotplates are turned off. The residual heat indicator will remain lit until the hotplates have cooled down sufficiently.

  • The hob switches off automatically when all the hotplates are

switched off for more than 20 seconds.

The power level has been set.

  • The settings are memorised for 4 seconds after the hob has

been turned off. If the hotplate is switched back on within this time then the previous settings will be applied.

Changing the power level

Select the hotplate and press the + or - symbol until the required power level comes on.

Set the hotplate

To switch off the hotplate

Select the required power level with the + and - symbols.

Select the hotplate and then press the + or - symbol until ‹ symbol appears.

Power level 1 = minimum power.

Power level 9 = maximum power.

The hotplate turns off and the residual heat indicator appears.

Each power level has an intermediate setting. This is marked with a dot.

  • If no pan has been placed on the hotplate, the selected

power level flashes. After a certain time has elapsed, the hotplate switches off.

Selecting the hotplate and the power level

The hob must be switched on.

  • If a pan has been placed on the hotplate before switching on
1. Select the hotplate with the $ symbol.

the hob, it will be detected within 20 seconds of pressing the main switch and the hotplate will be selected automatically. Once detected, select the power level within the next 20 seconds or the hotplate will switch off. If more than one pan is placed on the hob, only one will be detected when switching it on.

Cooking guidelines table

The table below contains some examples.

Cooking times depend on the power level, type, weight and quality of the food. As such they are approximate.

When heating purées, creams and thick sauces, stir occasionally.

Use power level 9 to begin cooking.

Power level Cooking time

Chocolate, chocolate coating 1-1. -

Butter, honey, gelatin 1-2 -

Heating and keeping warm

Stew (e.g., lentils) 1.-2 -

Milk** 1.-2. -

Sausages heated in water** 3-4 -

Frozen spinach 3-4 15-25 min.

Frozen goulash 3-4 30-40 min.

* Uncovered cooking ** Uncovered *** Turn frequently

Melting · Defrosting and heating

Page 6 of the Constructa CA424252 user manual — Programming the hob
Page 6 · cliquer pour agrandir
Page 6

Power level Cooking time

Potato dumplings* 4.-5. 20-30 min.

Fish* 4-5 10-15 min.

White sauces (e.g., bechamel) 1-2 3-6 min.

Whipped sauces (e.g., Bearnaise, Hollandaise) 3-4 8-12 min.

Rice (with a double amount of water) 2-3 15-30 min.

Rice pudding 2-3 30-40 min.

Unpeeled potatoes 4-5 25-30 min.

Peeled potatoes with salt 4-5 15-25 min.

Pasta* 6-7 6-10 min.

Soups 3.-4. 15-60 min.

Vegetables 2.-3. 10-20 min.

Greens, frozen foods 3.-4. 7-20 min.

Cooked in a pressure cooker 4.-5. -

Meat roll 4-5 50-60 min.

Stew 4-5 60-100 min.

Goulash 3-4 50-60 min.

Bake / Fry with a little oil**

Steaks, plain or breaded 6-7 6-10 min.

Frozen steaks 6-7 8-12 min.

Chops, plain or breaded*** 6-7 8-12 min.

Beefsteak (3 cm thick) 7-8 8-12 min.

Chicken breast (2 cm thick)*** 5-6 10-20 min.

Frozen chicken breast*** 5-6 10-30 min.

Hamburgers, meatballs (3 cm thick)*** 4.-5. 30-40 min.

Plain fish and fish fillet 5-6 8-20 min.

Breaded fish and fish fillet 6-7 8-20 min.

Frozen breaded fish (e.g., fish fingers) 6-7 8-12 min.

Prawns and shrimps 7-8 4-10 min.

Frozen meals (e.g., stir-fries) 6-7 6-10 min.

Pancakes 6-7 fry individually

Omelette 3.-4. fry individually

Fried eggs 5-6 3-6 min.

Frying** (150-200 g per serving with 1-2 l of oil)

Frozen foods (e.g., French fries, chicken nuggets) 8-9 fry one portion at a time

Meat (e.g., chicken pieces) 6-7

Fish, in breadcrumbs or batter 6-7

Greens, mushrooms, in breadcrumbs or batter (e.g., baby mushrooms) 6-7

Confectionery products (e.g., fritters, fruit in batter) 4-5

* Uncovered cooking ** Uncovered *** Turn frequently

Show 4 more labels / short text on this page
Slow cooking, simmering · Boiling, steaming, sautéing · Stewing · Frozen croquettes 7-8
Page 7 of the Constructa CA424252 user manual — Turning off a hotplate automatically
Page 7 · cliquer pour agrandir
Page 7

Childproof lock

The hob can be protected against being accidentally turned on, to ensure that children do not switch on the hotplates.

To deactivate: press the symbol ‚ for approximately 4 seconds. The lock is now deactivated.

Childproof lock

Activating and deactivating the childproof lock

With this function, the childproof lock automatically activates when a hob is switched off.

The hob should be turned off.

To activate: press the symbol ‚ for approximately 4 seconds. The indicator next to the symbol ‚ lights up for 10 seconds. The hob is locked.

All of the relevant information on the automatic childproof lock connection can be found in the Basic settings chapter.

Powerboost function

The Powerboost function can be used to heat large amounts of water more quickly than the power level Š.

To activate

1. Select a hotplate.
2. Press the › symbol. The › indicator lights up.

Restrictions when using

This function is available for all hotplates, provided that the other zone of the same group is not operating (see image). Otherwise, in the visual display of the selected hotplate › and Š will flash; then the power level will automatically set itself to Š.

The function should be activated.

To deactivate

1. Select a hotplate.

*URXS

*URXS

2. Press the › symbol. The › indicator will no longer appear and the hotplate will return to the power level Š .

The function will be deactivated.

*URXS

*URXS

Time program function

This function may be used in two different ways:

3. Press the + or - symbol. The basic setting appears: + symbol: 30 minutes. - symbol: 10 minutes.
  • to automatically switch off a hotplate
  • as a timer
Constructa CA424252 — *URXS diagram (page 7)
Fig. 2

Turning off a hotplate automatically

The hotplate turns off automatically once the selected time has elapsed.

Program the cooking time.

The hob must be switched on:

1. Select the desired hotplate and power level.
2. Press the 3 symbol. The Ú indicator on the hotplate lights up. ‹‹ is displayed on the time program function display.
4. Press the + or - symbol until the required cooking time appears.

After a few seconds, the cooking time begins to elapse.

Activating and deactivating

Page 8 of the Constructa CA424252 user manual — Basic settings
Page 8 · cliquer pour agrandir
Page 8

Changing or cancelling the time

  • If you have not selected the hotplate: press the 3 symbol.

Selecting the hotplate . Press the 3 symbol and change the cooking time with the + or - symbols, or set to ‹‹.

The Ú indicator next to the W symbol lights up. ‹‹ is displayed on the time program function display.

Once the time has elapsed

2. Press the + or - symbol. The basic setting appears. + symbol: 10 minutes. - symbol: 5 minutes.

The hotplate switches off. A beep sounds and in the time program function display ‹‹ appears for 10 seconds. The Ú indicator on the hotplate lights up. Pressing the 3 symbol turns off the indicators and stops the beeping.

3. Set the desired time using the + or - symbols.

After a few seconds, the time will start to elapse.

  • If cooking times have been programmed for various

Changing or cancelling the time

hotplates, the time programming function always displays the time for the selected hotplate.

Press the 3 symbol various times until the Ú indicator next to the W symbol lights up. Change the time or set to ‹‹ with the + or - symbols.

  • Any cooking time can be programmed for up to 99 minutes.

The timer

Once the time has elapsed

A warning signal sounds. ‹‹ is displayed on the time program function display. After 10 seconds the indicators turn off.

The timer can be set for periods of up to 99 minutes. It is independent of the other settings. This function does not automatically switch off a hotplate.

Pressing the 3 symbol turns off the indicators and stops the beeping.

1. The timer can be selected in two different ways:
  • If you have selected the hotplate: press the 3 symbol

twice.

Automatic time limitation

If the hotplate remains in use for a long time and no changes are made in the settings, the automatic time limitation function is triggered.

The indicator goes out when any symbol is pressed. The hotplate can now be reset.

When the automatic time function is used, it is governed by the selected power level (from 1 to 10 hours).

The hotplate stops heating. The ”, ‰ symbol and the residual heat indicator œ/• flash alternately in the display.

Basic settings

The device has several basic settings. These settings may be adapted to the user's individual needs.

‹ Deactivated.*

‚ Activated.

‹ Confirmation and error signals deactivated.

‚ Only error signal activated.

ƒ Only confirmation signal activated.

„ All signals activated.*

™† Automatic programming of cooking time.

‹ Switched off.*

‚-ŠŠ Automatic shut-off time.

™‡ Duration of the time program function warning signal

‚ 10 seconds*.

ƒ 30 seconds.

„ 1 minute.

Show 5 more labels / short text on this page
How to program · Indicator Function · ™‚ Childproof lock · ™ƒ Audible signals · *Factory settings
Page 9 of the Constructa CA424252 user manual — Hob
Page 9 · cliquer pour agrandir
Page 9

‹ = Deactivated.*

‚ = 1,000 W. minimum power.

‚.= 1,500 W.

ƒ = 2,000 W.

etc.

Š or Š. = maximum power of the hob.

™Š Hotplate time selection

‹ Unlimitedthe last hotplate programmed remains selected.*

‚ Limited: The hotplate will only remain selected for 10 seconds.

™‹ Return to basic settings

‹ Personal settings.*

‚ Return to factory settings.

Accessing the basic settings

3. Press the ‚ symbol several times until the required function indicator appears.

The hob should be turned off.

4. Next select the desired setting using the + and - symbols.
1. Switch on the hob.
Constructa CA424252 — Accessing the basic settings diagram (page 9)
Fig. 3 · Accessing the basic settings
2. Within the next 10 seconds, press the ‚ symbol for 4 seconds.
Constructa CA424252 — Accessing the basic settings diagram (page 9)
Fig. 4 · Accessing the basic settings
5. Press the ‚ symbol again for more than 4 seconds.

The settings will have been correctly saved.

In the display ™ and ‚ alternately light up and ‹ lights up as a default setting.

To leave the basic settings, turn off the hob at the main switch.

Care and cleaning

The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition

The best way to remove stubborn stains is to use a glass scraper. Follow the manufacturer's instructions.

Suitable glass scrapers can be obtained through the Technical Assistance Service or from our online shop.

Hob

Hob frame

In order to avoid damage to the hob frame, follow the indications below:

Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clean it.

  • Use only slightly soapy hot water
  • Do not use sharp or abrasive products

Only use cleaning products specifically designed for hobs. Follow the instructions provided on the packaging.

  • Do not use a glass scraper

Do not use:

  • Undiluted washing-up liquid
  • Dishwasher detergent
  • Abrasive products
  • Corrosive products such as oven sprays or stain removers
  • Sponges that may scratch
  • High-pressure or steam cleaners
Show 5 more labels / short text on this page
Indicator Function · ™ˆ Power-Management function · *Factory settings · Quit · Cleaning
Page 10 of the Constructa CA424252 user manual — Normal noise while the appliance is working
Page 10 · cliquer pour agrandir
Page 10

Fixing malfunctions

Malfunctions are usually due to small details. Before calling the Technical Assistance Service you should bear in mind the following advice and warnings.

none The electric power supply has been cut off. Use other electrical appliances to check whether there has been a power cut.

The appliance has not been correctly con- nected following the connection diagram.

Check that the appliance has been connected cor- rectly according to the connection diagram.

Electronic system malfunction. If none of the above checks resolve the malfunction, contact the Technical Assistance Service.

The indicators flash The control panel is damp or an object is rest- ing on it.

Dry the control panel area or remove the object.

The indicator - flashes on the hotplate indicators

A fault has occurred in the electronic system. Briefly cover the control panel with your hand to con-

firm the malfunction.

“§ + number / š + number / ¡ + number

Electronic system malfunction. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again.*

”‹ / ”Š There is an internal operating error. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again.*

”ƒ The electronic system has overheated and the corresponding hotplate has been switched off.

Wait until the electronic system has cooled down suffi- ciently. Then press any symbol on the hob. *

”… The electronic system has overheated and all hotplates have been switched off.

Ӡ + power level and beep

There is a hot pan on the control panel. It is highly likely that the electronic system will overheat.

Remove that pan. The malfunction indicator will switch off shortly afterwards. You can carry on cooking.

Ӡ and beep There is a hot pan on the control panel. The hotplate has switched off to protect the elec- tronic system.

Remove that pan. Wait a few seconds. Press any con- trol panel. When the malfunction indicator switches off, you can carry on cooking.

—‚ Incorrect supply voltage, outside normal oper- ating limits.

Contact your electricity board.

—ƒ / —„ The hotplate has overheated and has switched off in order to protect its hob.

Wait until the electronic system has cooled down suffi- ciently before switching it back on.

* If the warning persists call the Technical Assistance Service. Do not rest hot pans on the control panel.

Normal noise while the appliance is working

A high-pitched whistling sound

This noise is produced mainly in pans made from different materials superimposed on one another, and it occurs when such pans are heated at maximum power on two hotplates at the same time. The whistling disappears or becomes fainter as soon as the power level is lowered.

Induction heating technology is based on the creation of electromagnetic fields that generate heat directly at the base of the pan. Depending on how the pan has been manufactured, certain noises or vibrations may be produced such as those described below:

Noise from the fan

A deep humming sound as in a transformer

For proper use of the electronic system, the temperature of the hob must be controlled. To do this, the hob has a fan which turns on when a high temperature is detected. The fan may also work by inertia after the hob has been switched off, if the temperature detected is still too high.

This noise is produced when cooking with a high power level. It is caused by the amount of energy transferred from the hob to the pan. The noise disappears or becomes faint when the power level is lowered.

A low whistling sound

The noises described are normal, they are part of induction heating technology and not a sign of malfunction.

This noise is produced when the pan is empty. The noise disappears when water or food is added to the pan.

This noise occurs in pans which are made from different materials superimposed on one another. It is caused by the vibrations that occur in the adjoining surfaces of the different superimposed materials. The noise comes from the pan. The amount of food and cooking method can vary noise intensity.

Indicator Malfunction Solution · A crackling sound

Page 11 of the Constructa CA424252 user manual — Tested dishes
Page 11 · cliquer pour agrandir
Page 11

After-sales service

Our after-sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call-out.

Please note that a visit from an after-sales service engineer is not free of charge, even during the warranty period.

Please find the contact data of all countries in the enclosed customer service list.

E number and FD number:

Please quote the E number (product number) and the FD number (production number) of your appliance when contacting the after-sales service. The rating plate bearing these numbers can be found on the appliance certificate.

Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Tested dishes

This table has been prepared for assessment institutions to provide controls for our appliances.

  • Saucepan: 16 cm Ø, 1.2 l, for 14.5 cm Ø hotplates
  • Pot: 16 cm Ø, 1.7 l, for 14.5 cm Ø hotplates

The table data refers to our Schulte-Ufer cookware accessories (4-piece cookware set for the CZ9442X0 induction hob) with the following dimensions:

  • Pot: 22 cm Ø, 4.2 l, for 18 cm Ø hotplates
  • Pan: 24 cm Ø, for 18 cm Ø hotplates

Tested dishes Hotplate Power level Time (Min:S) Cover Power level Cover

Cookwaresaucepan

Ø 14.5 cm - - - 1 - 1. No Chocolate coating (e.g. Dr. Oetker brand, dark 55%, 150 g.)

Heating lentil stew and keeping it heated

CookwarePot

Initial temperature 20 °C

Amount 450 g. Ø 14.5 cm 9 1:30 without stir- ring Yes 1. Yes

Amount800 g. Ø 18 cm 9 2:30 without stirring Yes 1. Yes

Canned lentil stew, e.g. Erasco lentils with chorizo

Amount 500 g. Ø 14.5 cm 9 1:30 stir after approx. 1:00 Yes 1. Yes

Amount 1 kg. Ø 18 cm 9 2:30 stir after approx. 1:00 Yes 1. Yes

CookwareSaucepan
Milk temperature7 °C

Ingredients: 40 g of butter, 40 g of flour, 0.5 l of milk (3.5% fat) and a pinch of salt

Ø 14.5 cm

1. Melt butter, mix in flour and salt and heat everything together 1 approx. 3:00 No
2. Add milk and bring the sauce to a boil, stirring continuously 7 approx. 5:20 No
3. Keep the bechamel sauce at a boil for two more minutes, stirring continuously 1 No

*Recipe according to DIN 44550 ***Recipe according to DIN EN 60350-2

Show 4 more labels / short text on this page
Preheating Cooking · Melting chocolate · Lentil stew* · Making bechamel sauce
Page 12 of the Constructa CA424252 user manual — After-sales service
Page 12 · cliquer pour agrandir
Page 12

Tested dishes Hotplate Power level Time (Min:S) Cover Power level Cover

CookwarePot
Milk temperature7 °C

Heat milk until it begins to bubble. Change the rec- ommended heating level and add rice, sugar and salt to the milk

Ingredients: 190 g. of short-grain rice, 23 g. of sugar, 750 ml. of milk (3.5% fat) and a pinch of salt

Ø 14.5 cm

2 stir after approx.

10:00 Yes Ingredients: 250 g. of short-grain rice, 30 g. of sugar, 1 l. of milk (3.5% fat) and a pinch of salt Ø 18 cm

8. approx. 6:30 No
CookwarePot

Water temperature 20 °C

Ingredients: 125 g of short-grain rice, 300 g of water and a pinch of salt Ø 14.5 cm 9 approx. 2:30 Yes 2 Yes

Ingredients: 250 g of short-grain rice, 600 g of water and a pinch of salt Ø 18 cm 9 approx. 2:30 Yes 2. Yes

CookwareFrying pan

Ø 18 cm 9 1:30 No 7 No Sirloin initial temperature: 7 °C

2 pieces of sirloin (total weight approx. 200 g, 1 cm thick)

CookwareFrying pan

Ø 18 cm 9 1:30 No 7 No 55 ml of crêpe batter

Frying frozen potato chips

CookwarePot

Ø 18 cm 9 Until the tempera-

No 9 No Ingredients: 1.8 kg of sunflower oil, for cooking: 200 g of frozen potato chips (e.g. McCain 123 Frites Original)

ture of the oil reaches 180 °C

*Recipe according to DIN 44550 ***Recipe according to DIN EN 60350-2

Show 5 more labels / short text on this page
Preheating Cooking · Cooking rice pudding · Cooking rice* · Pan-frying pork sirloin · Frying crêpes**
Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Constructa CA424252

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Constructa CA424252

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Constructa CA424252 manuel PDF

56 pages·1.7 MB·Plaque à induction·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…