FR
AEG logo
Notice d'utilisation officielle

AEG SR 4352 CD MP3

58 pages·6.1 MB·Radio portable·PDF·ENJA
AEG SR 4352 CD MP3
Table des matières 15 sections Instruction Manual · General Safety Instructions · Special safety information · Overview of the Components · … AfficherMasquer
Page 1 of the AEG SR 4352 CD MP3 user manual — Special safety information
Page 1 · cliquer pour agrandir
Page 1

Instruction Manual

  • Never open the device’s case. Improper repairs can cause severe danger to the user. If the device or particularly the power cord is damaged, don’t use the device any further and have it repaired by a qualified specialist. Check the power cord regularly for damages.
  • To avoid any danger, a damaged power cord must be replaced only by the producer, its customer service or a similarly qualified person with an equal cord.
  • If the device won’t be used over an extended period of time, disconnect the power cord and remove the batteries.

Thank you for choosing our product. We hope you enjoy using the device.

Symbols in these Instructions for Use Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine:

These symbols may be found on the machine and are intended to indicate the following:

The lightning symbol should advise the user of parts in the inside of the device which carry dangerously high voltage levels.

The symbol with an exclamation mark should advise the user of important operation or maintenance instructions in the accompany- ing documentation. Devices bearing this symbol work with a “class 1 laser” for tracing the CD. The built-in safety switches should prevent the user being exposed to dangerous laser light, which is invisible to the human eye, when the CD compartment is opened.

General Safety Instructions

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the in- ternal packing. If you give this device to other people, please also pass on the operating instructions.

  • To avoid the risk of fire or electric shock, you should not expose the device to rain or humidity. Do not use the device near water (e.g. bathroom, swimming pool, humid cellars).
  • Do not use the unit in extremely hot, cold, dusty, or damp places.
  • The unit is designed solely for private use and its intended purpose. This unit is not designed for commercial use.
  • Make sure that the power cable is not bent, pinched, or comes into contact with heat sources.
  • Make sure that the power cable is not a tripping hazard.
  • Never touch the mains plug or the cord with wet hands.
  • Always connect the unit to a properly installed plug socket. Be sure the device voltage corresponds to the grid voltage.
  • The mains plug must always be easily accessible.
  • Always install batteries in the correct direction.
  • Avoid covering the device’s vent openings.
  • Never cover the vent holes with objects, such as magazines, tablecloths, curtains etc.
  • This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on apparatus.
  • Open sources of fire, such as e.g. burning candles may not be placed onto the unit.

Children and Frail Individuals • In order to ensure your children‘s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

  • This device is not intended to be used by individuals (including children) who have restricted physical, sensory or mental abilities and/or insufficient knowledge and/or experience, unless they are supervised by an individual who is responsible for their safety or have received instructions on how to use the device.
  • Children should be supervised at all times in order to ensure that they do not play with the device.

Special safety information

This device works with a class 1 laser.

Page 2 of the AEG SR 4352 CD MP3 user manual — Start-up of the device/introduction
Page 2 · cliquer pour agrandir
Page 2

Overview of the Components

  • Select a suitable location for the device, such as a dry, flat, non-slip surface on which it is easy to operate the machine.
  • Ensure that the device is sufficiently ventilated!
  • Remove the protective film from the display if it is still present.

1 Handle 2 Telescopic antenna 3 CD compartment 4 Band selector switch (FM ST / AM) 5 Radio scale 6 TUNING control 7 PUSH OPEN CD tray (open/close) 8 / button (Play/Pause / deactivate standby) 9 NEXT button (forward search) 10 FOLD+/+10 button (Skip track/ album up) 11 LCD display 12 PROG/P-MODE button (Memory/Repeat/random play- back) 13 FM ST. control lamp 14 FOLD-/-10 button (Skip track/ album down) 15 BACK button (reverse search) 16 STOP button 17 POWER control lamp 18 VOLUME (volume control) 19 FUNCTION Function selector switch (RADIO / OFF / CD/MP3/AUX)

  • Power Supply
  • Connect the power cable supplied (see battery compartment if necessary) to a properly installed safety power socket and the mains connector AC on the back of the machine.
  • Ensure that the voltage is the same as that indicated on the model identification plate.
  • Inserting the Batteries (not supplied)
  • Open the lid of the battery compartment on the bottom.
  • Insert 6 batteries of type C/R14 1.5 V. Please ensure that the polarity is correct (see the floor of the battery compartment)!
  • If the device is not used for a long period of time, remove the batteries to avoid the spilling of battery acid.
  • Then close the battery lid.

Reverse (not shown) AC Mains connection AUX IN jack (3.5 mm jack plug)

  • CAUTION:
  • Different battery types or new and used batteries must not be used together.
  • Batteries are not to be disposed of together with domestic wastes. Dispose of the used batteries at the relevant collection bin or at your dealer’s.

Underside (not shown) Battery compartment

Intended Use

This device is used for:

  • The reception of radio programmers
  • Playing back audio/MP3 CDs
  • Audio reproduction of external audio sources.

It is intended exclusively for this purpose and may only be used as such. It may only be used in the manner described in these instruc- tions for use. The device must not be used for commercial purposes.

  • Transport Safety Device, CD Compartment
  • Open the CD tray (3) by pressing the PUSH OPEN button (7).
  • Before operating the machine for the first time, remove the transport safety device from the CD player if it is still in place.

Any other use of this device is considered to be contrary to the intended use and may result in damage to materials or even personal injury.

The firm ETV – Elektro-Technische Vertriebsgesellschaft mbH does not accept any liability for damage caused as a result of the use of this device contrary to its intended use.

Volume The desired volume can be sent using the VOLUME regula- tor (18).

Start-up of the device/introduction

Switch-off The machine is switched off when the function selector switch (19) is turned to the OFF position. The POWER (17) control lamp goes off. Unplug the device.

  • Please read the operating instructions carefully before using the device for the first time!
Page 3 of the AEG SR 4352 CD MP3 user manual — Playing CDs/MP3
Page 3 · cliquer pour agrandir
Page 3
5. Press the / button (8) to restart playback. The CD will play from the first title. The current track and the “CD

AUX IN jack 1. Connect the 3.5 mm stereo RCA cable to an external audio source. If required, use a suitable adapter (not included). 2. Insert the other end of the cable into the AUX-IN jack (Back Side) on the unit. 3. Set the function selector switch (19) to the “CD/MP3/ AUX” position. 4. Start the playback of your audio source. Listen to the sound playback via the speaker. 5. For the further procedure, please refer to the user manual of the external audio source.

“ or “MP3 “ message are shown on the display.

6. In order to remove a CD, please press the STOP button (16), open the CD compartment and lift the CD out carefully.

Always keep the CD deck closed.

  • NOTE:
  • If a disc is inserted the wrong way, or if no disc is inserted, the message “– – –” will flash and “NOd” will appear on the display.
  • Playback of CDs produced by the user cannot be guaranteed due to the large variety of software and CD media available.

Listening to the Radio

Description of the CD buttons

1. Set the function selector switch (19) to the “RADIO” position. 2. Select the desired frequency band with the band selector switch (4).

/ (8) You can briefly interrupt and resume playback using this button. The symbol“ “ flashes on the display. Pressing again continues playback.

VHF (Stereo) = FM.ST, Medium wave = AM (Mono)

2. Tune in the desired station with the station adjustment knob TUNING (6). 3. The FM ST. indicator lamp (13) will only be lit, when the station is received in stereo quality. If reception is too weak and there is noise on the station being received, this lamp will flicker. 4. For FM mode pull out the telescopic antenna (2) and turn it to improve reception. 5. An aerial is integrated into the device for the reception of AM stations. The machine can be aligned to the station by turning it. In this frequency band programs are trans- mitted in “mono” only.

NEXT/ BACK (9/15) When playing an audio CD or a CD in MP3 format: With NEXT you can jump to the next or previous track etc. • If the button is kept pressed down, the machine starts to search through the tracks.

The BACK button can be used as follows: Press once = This jumps back to the previous track. Press twice = This plays the song before etc. If the button is kept pressed down, the machine starts to search through the tracks.

STOP (16) The CD stops.

Playing CDs/MP3

This is how you play a CD 1. Turn the function selector switch (19) to the “CD/MP3/ AUX”. 2. Open the CD tray (3) by pressing the PUSH OPEN button (7). 3. Insert an audio CD with the printed side facing upwards on to the central cone so that the CD clicks into place and then close the lid of the CD compartment. 4. After a few seconds the total number of songs/tracks is shown in the display.

  • PROG./P-MODE (12)
  • In stop mode for programming any order of tracks (see the section on “Programmed Play”).
  • When playing back music to select the replay mode (see next chapter).

When playing an audio CD: Press once = (The symbol flashes) the current track is repeated continuously.

Page 4 of the AEG SR 4352 CD MP3 user manual — Troubleshooting
Page 4 · cliquer pour agrandir
Page 4

Press twice = (The symbol is lit) the whole CD is played continuously. Press three times = (RDM appears in the display) all titles are

7. To delete the program, press the STOP button twice. The PROG control lamp goes out.

The device stops automatically after all the programmed titles have been played back. The PROG display will go out and the programmed sequence will be deleted from the memory.

replayed successively in random order. Press four times = (INTRO appears in the display) every title

of the CD is played for 10 seconds each. Press five times = All functions are cancelled. The normal

play mode is resumed.

Playing back Music in MP3 Format

Only when playing CD’s in MP3 format: Press once = (The symbol flashes) the current track is repeated continuously. Press twice = The selected folder of the MP3 CD is repeated continuously ( FOLDER appears in the display). Press three times = (The symbol is lit) the whole CD is played continuously. Press four times = (RDM appears in the display) All titles are

With this device it is possible to play back pieces of music in MP3 format. The device also supports all standard CD types: CD, CD-RW, CD-R.

This machine of is able to play MP3 CDs. Up to 200 tracks can be compressed and stored on these CDs. Your machine detects an MP3 CD automatically (the total number of tracks and MP3s appears in the display). If you would like to play one of these CDs, proceed as described under “Playing CDs/MP3”. Tracks can be programmed as described under “Playing Back Programmed Tracks”.

replayed successively in random order. Press five times = The function is deactivated and the CD is

played in the normal mode.

Please note: There are a number of different recording and compression methods, as well as quality differences between CDs and self- recorded CDs.

  • FOLD+/+10 and FOLD-/-10 (10/14) (only with MP3 CD’s)
  • Press this button during playback to skip forward, or back by 10 titles each (if more than 10 titles are stored on a CD).
  • Keep the button pressed down to select the next or previous folder (if the CD contains several folders).

Furthermore, the music industry does not adhere to fixed standards (copy protection).

For these reasons it is possible that in rare cases there are problems with the playback of CDs and MP3 CDs. This is not a malfunction of the device.

Programmed Play

This can be used to program any desired sequence of tracks. 1. Press the STOP button (16). 2. Press the “PROG./P-MODE” button (12). “P01” (preset location) appears on the display and PROG flashes on the display. Use the NEXT/ BACK buttons (9/15) to select the desired track and then press the “PROG./ P-MODE” button again. The display changes to memory slot P02. 3. Select the next track with the NEXT/ BACK button and press the “PROG./P-MODE” button again. Repeat the procedure until all the desired tracks are selected.

Cleaning and Maintenance

  • Always remove the mains plug before cleaning the machine.
  • Any marks on the surface can be wiped off with a slightly damp cloth without any additives.

Troubleshooting

Symptoms Course Solution CD can not be played back.

CD is not inserted or inserted incor- rectly.

Ensure that the disc is inserted with the label facing upwards. Batteries too weak. Insert new batteries

4. Press the / button (8). The playback starts. The first selected track number is shown on the display, the message “CD “ or “MP3 “ and PROG is shown on the display. 5. Press once the STOP button to stop the playback while retaining the program. 6. To play the programme back again, press the / button.

or operate the device with the mains lead. CD jumps dur- ing playback.

Check the disc for fingerprints, dirt or scratches. Device cannot be operated.

Check the disc for fingerprints, dirt or scratches.

Device crashes and “hangs”.

Disconnect the power supply for 5 sec. Then switch the device on again.

Page 5 of the AEG SR 4352 CD MP3 user manual — Technical Data
Page 5 · cliquer pour agrandir
Page 5

Disposal

Meaning of the “Dustbin” Symbol Protect our environment: do not dispose of electrical equip- ment in the domestic waste.

Technical Data

Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.

Model: SR 4352 CD/MP3 Power supply: AC 230 V~ 50 Hz Battery operation: 6 x 1.5 V Type C/R14 Power consumption: 13 W Protection class: II Net weight: 1.39 kg Radio section:

This helps avoid the potential effects of incorrect disposal on the environment and human health.

This will contribute to the recycling and other forms of reutili- sation of electrical and electronic equipment.

Frequency ranges: FM 88 ~ 108.0 MHz

Information concerning where the equipment can be dis- posed of can be obtained from your local authority.

AM 540 ~ 1600 KHz

The right to make technical and design modifications in the course of continuous product development remains reserved.

This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Dépannage

Dépannage

Problèmes fréquents, causes probables et solutions.

ProblèmeCause possibleSolution
CD can not be played back.Ensure that the disc is inserted with the label facing upwards. p.4
CD can not be played back.Insert new batteries or operate the device with the mains lead. p.4
CD jumps dur- ing playback.Check the disc for fni gerprints, dirt or scratches. p.4
Device cannot be operated.Disconnect the power supply for 5 sec. Then switch the device on again. p.4

Poser une question sur : AEG SR 4352 CD MP3

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le AEG SR 4352 CD MP3

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

AEG SR 4352 CD MP3 manuel PDF

58 pages·6.1 MB·Radio portable·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…