Manuel d'utilisation / d'entretien du produit ZWN 6120 L du fabricant Zanussi
Aller à la page of 24
EN User manual Washing Machine ZWN 6120 L.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 First use _ _ _ _ _ _ .
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Always be sure, that there is no water leakage from ho- ses and their connections after the installation.
Product description 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adju stable feet 1 2 3 4 5 6 Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available).
Control panel Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot lights. These are presented by relevant numbers on the following pages.
Indicator pilot light (7) When selecting a washing programme both lights 7.1 and 7.2 illuminate. After having pressed the button 5 the only light corre- sponding to the running phase stays on. The machine starts working and the door is locked. The light 7.
Flap for powder or liquid detergent UP- The flap position if using POWDER detergent DOWN - The flap position if using LIQUID detergent during main wash If the flap is not in the desired position: MAX • Pull out the dispenser drawer until it stops. The flap is down and you wish to use powder detergent: • Turn the flap up.
The selector dial can be turned either clockwise or coun- terclockwise. Turn to position to reset programme/ Switching the machine off. At the end of the programme the selector dial must be turned to position , to switch the machine off.
If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to . After a few minutes the door can be opened (pay attention to the water level and temperature!) . After closing the door, it is necessary to select the pro- gramme and options again and to press button 5 .
Ink: depending on the type of ink, moisten the fabric first with acetone 1) , then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thor- oughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment COTTONS ECO 60° and 40° Main wash - Rinses Maximum spin speed at 1200 rpm Max. load 8 kg This programme can be selected for normally soiled cotton items.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment WOOL 40° Main wash - Rinses Maximum spin speed at 900 rpm Max. load 2 kg Washing programme for machine washable wool as well as for hand washable woollens.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment SPIN Drain and long spin Maximum spin speed at 1200 rpm Max. load 8 kg Separate spin for hand washed garments and after programmes with the Rinse Hold option selected.
Cleaning the pump The pump should be inspected regularly and particularly if: • the appliance does not empty and/or spin; • the appliance makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump; • a problem with water draining is detected (see chapter “What to do if.
Cleaning the water inlet filt ers Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked .
What to do if… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
Problem Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (cre ates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rota- tion of the drum.
Consumption values Programme Energy consumption (kWh) 1) Water consumption (litre) 1) Programme duration (minutes) 1) White Cottons 90 °C 2.1 65 145 Cottons 60 °C 1.4 63 120 Cottons 40 °C 0.6 63 140 Synthetics 40 °C 0.45 37 85 Delic ates 40 °C 0.
Unscrew the three bolts. Slide out the relevant plas- tic spacers. Open the porthole and re- move the polystyrene block fitted on the door seal. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.
The other end of the inlet hose which connects to the appliance can be turned as showe d in the picture. Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. Set the hose correctly by loosening the ring nut.
If the outlet spigot has not been used before, remove any blanking plug that may be in place. Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose (see above) to prevent waste from th e sink enter- ing the appliance.
your local council, your household waste disposal service or the shop where you purchas ed the product. Packaging materials The materials marked with the symbol are recyclable.
www.zanussi.com/shop 192985530-A-312011.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Zanussi ZWN 6120 L c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Zanussi ZWN 6120 L - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Zanussi ZWN 6120 L, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Zanussi ZWN 6120 L va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Zanussi ZWN 6120 L, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Zanussi ZWN 6120 L.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Zanussi ZWN 6120 L. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Zanussi ZWN 6120 L ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
