Manuel d'utilisation / d'entretien du produit XADC du fabricant Xantrex Technology
Aller à la page of 26
About These Installation Instructions - - - - - - - - - - - - - - - - - - - - - - 2 Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Installation - - - - - - - - -.
Xantrex AC to DC Converter 2 975-0301-01-01 About These Installation Instructions Purpose The purpose of these Installatio n Instructions is to pro vid e explanations a nd procedures for installing the Xantrex AC to DC Converter (XADC). The Installation Instructions provide safety guidelines and procedures for installing the XADC.
Installation Instructions 975-0301-01-01 3 Important Safety Instructions 1. Before installing and using the XADC, re ad all instructions and cautionary markings on the XADC, the batteries, an d all appropriate sections of this guide. 2. Do not expose the XADC to rain, snow , spra y , or water .
Xantrex AC to DC Converter 4 975-0301-01-01 Explosive Gas Precautions Precautions W hen W orking With Batteries 3. Make sure the area around the battery is well ventilated. 4. Never smoke or allow a spark or flame near the engine or batteries. 5. Use caution to reduce the risk or dropp i ng a metal tool on the battery .
Installation Instructions 975-0301-01-01 5 12. Use the XADC for charging a lead-aci d battery only . Do not use the XADC to charge nickel-cadmium or dry-cell ba tteries commonly used with home appliances and electroni c equipment. These batteries may burst and cause injury to persons and damage to pro perty .
Xantrex AC to DC Converter 6 975-0301-01-01 Installation Main Components Figure 1 and Figure 2 sh ow the main compon ents of the XADC. Figure 1 XADC External Components Item Description 1 AC wiring co.
Installation Instructions 975-0301-01-01 7 A C/DC Distribution P anel The XADC may be pre-installed with an AC/DC Distribution Panel. The panel is available in two configurations which provides th e a.
Xantrex AC to DC Converter 8 975-0301-01-01 Figure 3 AC/DC Distribution P anel Components Item Description 1 DC fuse/AC breaker access panel (swings open with thumb latch) 2 Removable DC fuse access panel with DC circuit designation label.
Installation Instructions 975-0301-01-01 9 Figure 5 AC/DC Distribution P anel and XADC Internal Components Item Description 1 Equipment Grou nding T erm inal bus (front) 2 AC Neutral T erminal bus (rear) 3 AC wiring knockouts (½ in. - 3/8 in. trade size - and ¾ in.
Xantrex AC to DC Converter 10 975-0301-01-01 Installation Codes Governing installatio n codes vary depe nding on the spec ific location and application of the installation. It is the in staller’ s responsibility to ensure that all applicable installation requ irements are met.
Installation Instructions 975-0301-01-01 11 • XADC converter faceplate and mounting hardware • Plastic bag containing two mounti ng tabs and related hardware, one top mounting flange and related h.
Xantrex AC to DC Converter 12 975-0301-01-01 Installing the XADC (stand-alone unit) Follow the procedures in the order giv en: 1. “Preparing to Install” 2. “Preparing the Mountin g Location for the XADC” 3. “Connecting the DC Batter y” 4. “Connecting the AC In put” 5.
Installation Instructions 975-0301-01-01 13 Preparing the Mounting Location for the XADC T o prepar e the XADC mounting location: 1. Place the XADC into the intended m ounting position and hold it against the mounting surface. 2. Mark the positions of the four side flange mounting screws, and then remove the XADC.
Xantrex AC to DC Converter 14 975-0301-01-01 Connecting the A C Input When following the procedure, se e T able 1 on pa ge 24 for torque values. T o connect the AC input: 1. Route AC wires through the AC wiring compartment hole. 2. If you plan to use the ¾ in .
Installation Instructions 975-0301-01-01 15 Mounting the XADC T o mount the XADC using the mounting plates: 1. Align the XADC with the 4 prev iously marked mounting positions. 2. Fasten the XADC using 4 × #6 or # 8 pa n head, round head or washe r hea d screws suitable for mounting unit onto particleboard or wood.
Xantrex AC to DC Converter 16 975-0301-01-01 4. AC breaker positions 1 and 2 have been removed from the removable faceplate on the panel. Remove extra positions from the pa nel by twisting the knockouts back and fo rth.
Installation Instructions 975-0301-01-01 17 4. T ake one of the side mounting flanges that you removed in step 2 above, and screw it to the bottom of the XADC.
Xantrex AC to DC Converter 18 975-0301-01-01 Preparing the Mounting Locati on for the XADC and P anel T o prep are the XADC and panel moun ting location: 1.
Installation Instructions 975-0301-01-01 19 3. Connect the incoming negative (-) black cable from each of the loads to the negative DC bus . 4. Connect the incoming positive (+) red cable from each of the loads to the positive DC bus. 5. Install fuses for the DC loads and th e DC batter y .
Xantrex AC to DC Converter 20 975-0301-01-01 Connecting the P anel to the XADC DC Side When following the procedure, se e T able 2 on pa ge 24 for wire lengths and T able 1 on page 24 for torque values. T o connect the panel to the XADC DC side: 1. Remove the DC wiring compartment panel on th e XADC (see Figure 8).
Installation Instructions 975-0301-01-01 21 Connecting the P anel to the XADC A C Side When following the procedure, se e T able 2 on page 24 for wire lengths and T able 1 on page 24 for torque values. See Figure 4 on page 8 for panel electrical connection diagrams.
Xantrex AC to DC Converter 22 975-0301-01-01 Connecting the A C to the P anel See “Connection T ypes for AC and DC” on page 18 if you are not familiar with the connec tions used on the breakers. When following the procedure, se e T able 2 on pa ge 24 for wire lengths and T able 1 on page 24 for torque values.
Installation Instructions 975-0301-01-01 23 A C Loads T o install the AC loads: 1. Route the AC load cables through the knockouts in the back of the panel. 2. Install breaker(s) for your AC load s. See the documentation for yo ur b reaker to determine ho w it installs.
Xantrex AC to DC Converter 24 975-0301-01-01 Mounting the XADC and P anel Remotely T o mount the XADC and panel remotely: 1. Slide the panel into the mounting cuto ut (12 in.
Installation Instructions 975-0301-01-01 25 Specifications All specifications are subject to change without notice. Additi onal specifications are available in the Xantrex AC to DC Converter Owner ’ s Manual (Part #: 975- 0305-01-01).
Xantrex AC to DC Converter 26 975-0301-01-01 T rademar ks Xantrex AC to DC Converter is a trademark of Xantrex Inte rnational. Xantrex is a regi stered trademark of Xantrex Internationa l. Other trademar ks, registere d trademarks, an d product names are the property of their respective owners and are used herein for identification purposes only .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Xantrex Technology XADC c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Xantrex Technology XADC - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Xantrex Technology XADC, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Xantrex Technology XADC va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Xantrex Technology XADC, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Xantrex Technology XADC.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Xantrex Technology XADC. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Xantrex Technology XADC ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
