Manuel d'utilisation / d'entretien du produit 93-2007 (200106010) du fabricant Tripp Lite
Aller à la page of 22
Owner’ s Man ual 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 • www .tripplite.com Intr oduction 2 Impor tant Safety Instructions 4 Configuration & Connection 5 Features 11 Maintenance and Service 14 PowerV erter ® is a registered trademark of T ripp Lite.
2 Intr oduction Congratulations! Y ou’ ve purchased the most advanced, feature-rich integrated in verter and battery charger on the market. Y our APS pro vides your equipment with utility-supplied A.
3-Stage Battery Charger Y our APS rechar ges your battery faster than con ventional char gers because its three-stage charger prof ile (Bulk, Absorption and Float) are optimized, regardless of the type of battery you use (W et or Gel).
4 Impor tant Safety Instructions SA VE THESE INSTRUCTIONS This manual contains important instructions and warnings that should be f ollowed during the installation, operation and storage of all T ripp Lite APS Systems. APS Location W arnings • Install your APS indoors, away from excess moisture or heat, dust or direct sunlight.
5 Configuration DIP SWITCH GROUP A (All models) BA TTER Y TYPE / VOL T AGE POINT Using a small tool, set the 4 “Battery T ype / V oltage Point” Configuration DIP Switches, Group A (located on the front panel of your APS; see Diagram 1, p.
6 DIP SWITCH GROUP B (A vailable on Select Models) LOAD SHARING/EQ U ALIZE BA TTER Y CHARGE Using a small tool, set the “Load Sharing” Configuration DIP Switches, #1 and #2 of Group B (located on the front panel of your APS; see Diagram 1, p. 36).
7 • Equaliz e Battery Charge (DIP Switch #3, Group B) This DIP Switch is momentarily engaged to begin the process of equalizing the internal resistance of your battery’ s cells.
8 Mounting (Optional) (See Diagram 2, p . 36) Battery Selection Select a battery or system of batteries that will provide your APS with proper DC voltage and an adequate amp hour capacity .* Select ‘Deep-Cycle’ batteries to enjo y optimum performance from your APS.
9 Battery Connection 1. Connect your APS’ s positiv e DC T erminal directly to a fuse. T ripp Lite recommends that you install a recognized component fuse block and fuse within 18 inches of the battery . The fuse's rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model’ s specifications on pages 16 or 17.
10 APS systems must be connected to a grounded, permanent wiring system. For most installations, the negati ve battery conductor must be bonded to the grounding system at one (and only one) point in the system. All installations must comply with national and local codes and ordinances.
11 A C Connection continued Simply plug your equipment into the unit’ s A C receptacles. If adapters must be used, choose adapters that provide a connection to ground. • Switch to “ A UTO/REMO TE” when you are using connected equipment. AD V ANT AGE: Uninterruptible power supply .
12 4. “LINE” (All models): This green light will turn continuously ON whene v er connected equipment is receiving utility-supplied A C power and your APS is set to “ A UTO/REMO TE”, meaning that it will provide battery backup if utility po wer fails.
13 9. DC Input T e rminals (All models): The terminals’ lug scre ws secure the wires leading from your external battery or battery system. Y our battery or battery system must provide your APS with proper DC voltage and your equipment with an adequate amp hour capacity .
14 Limited W arranty Maintenance & Service Y our APS model requires no maintenance b ut should be kept dry at all times. Periodically check all cable connections both at the unit and at the battery .
15 T r y these remedies for common APS problems bef ore calling f or help. Call T ripp Lite Customer Ser vice at (773) 869-1234 before returning your APS f or service. SYMPT OM PROBLEMS CORRECTIONS APS does not provide APS not properly connected to Connect APS to utility power .
16 Specifications (Corded Models) CORDED MODELS: APSINT1012 Weight: 11.9 Kg INVERTER Continuous power (@ 20° C): 1000 W Surge power (5 seconds): 2000 W Efficiency (Full Load): 88% Minimum DC Fuse Rating: 170A DC Input Current @ Nominal V DC Full Load 95A No Load 2.
17 Specifications (Hard wired Models) HARDWIRED MODELS: APSINT1524 APSINT2012 Weight: 12.7 Kg 17.1 Kg INVERTER Continuous power (@ 20° C): 1500 W 2000 W Surge power (5 seconds): 3000 W 4000 W Efficiency (Full Load): 89% 87% Minimum DC Fuse Rating: 90A 370A DC Input Current @ Nominal V DC Full Load 70A 192 A No Load 1.
36 OUTPUT/NEUTRA OUTPUT/HOT GROUND INPUT/NEUTRA INPUT/HOT “FOR USE WITH COPPER WIRE ONLY” Diagrams/Esquemas See “Configuration”, pg. 5. 1.1 is DIP Switch Group A. 1.2 is DIP Switch Group B . Refiérase a la sección “Configur ación”, página 22.
37 X/2 V olts X/2 V olts APS See Battery Connection, Pg. 9. 4.1 is the fuse. X = Y our APS’s In verter's Nominal Input V oltage. (See specs.) Refiérase a la sección “Cone xión de Baterías”, página 26. 4.1 representa el fusible. X = El V oltaje Nominal de Entrada del Inv ersor del APS.
38 APS 12V 12V Basic 12VDC Vehicular Battery Connection. See Pg. 9. 7.1 is the alternator. 7.2 is the vehicle battery ground. 7.3 is the vehicle battery . 7.4 is the fuse. Conexión Básica de Baterías de 12V de CD en Vehículos. Vea página 27. 7.1 representa el alternador.
39 1. Operating Mode Switch (All models) 2. DIP Switch Group A (All models) 3. DIP Switch Group B (Select models only) 4. “LINE” (All models) 5. “INV” (In ve r ting—all models) 6. “LOAD” (All models) 8. “BA TTER Y HI/MED/LO” (All models) 9.
40 OUTPUT/NEUTRA OUTPUT/HOT GROUND INPUT/NEUTRA INPUT/HOT “FOR USE WITH COPPER WIRE ONL Y” Diagrams/Esquemas 9b 1. Operating Mode Switch (All models) 2. DIP Switch Group A (All models) 3. DIP Switch Group B (Select models only) 4. “LINE” (All models) 5.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Tripp Lite 93-2007 (200106010) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Tripp Lite 93-2007 (200106010) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Tripp Lite 93-2007 (200106010), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Tripp Lite 93-2007 (200106010) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Tripp Lite 93-2007 (200106010), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Tripp Lite 93-2007 (200106010).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Tripp Lite 93-2007 (200106010). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Tripp Lite 93-2007 (200106010) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
