Manuel d'utilisation / d'entretien du produit M5910(G) du fabricant Acer
Aller à la page of 75
Acer Aspire M5910(G) Service Guide PRINTED IN T AIW AN.
ii Revision History Please refer to the table below for the updates ma de on this service guide. Date Chapter Up dates.
iii Copyright Copyright © 2010 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any.
iv Disclaimer The information in this guide is subject to ch ange without notice. Acer Incorporated makes no representations or warranties, either e xpressed or implied, w ith respect to th e contents hereof and specifically disclaims any warrantie s of merchantability or fitnes s for any particular purpose.
v Conventions The following conventi ons are used in this manual: SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives additional informati on related to the current topic. W ARNING Alerts you to any physical risk or system damage that might result from doing or not doing specific actions.
vi Service Guide Coverage This Service Guide provides you with all technica l information relating to the BASIC CONFIGURA TION decided for Acer's "glo bal" product offering.
vii System Tour 1 Features 1 Block Diagram 4 System Compon e nt s 5 Front Panel 5 Rear Panel 6 Hardware Specifications and Configurations 7 Power Management Function( ACPI supp ort function) 10 System.
viii FRU (Field Replaceable Unit) List 61 Aspire M5910(G) Expl oded Diagram(AM551 ASSY) 62 Aspire M5910(G) Expl oded Diagram(AM550 ASSY) 63 Aspire M5910(G) FRU List 64.
Chapter 1 1 Features Below is a brief summary of the computer ’s many feature: NOTE: The features listed i n this section is for your re ference only .
2 Chapter 1 • 1GB to 16GB Max memory support • Design Criteria: • Must meet Intel L ynnfield and Clarkdale Chipset platform design guide Hard disk • Support up to two SA T A ports • 3.5", 25.4mm • Capacity and models are listed on A VLC Optical disk • Support two SA T A 5.
Chapter 1 3 USB ports • Ports Quantity: 12 • 6 back panel ports • On-board: 2 2*5 headers • 4 ports for front daughter board • Connector Pin: standard Intel FPIO pin defi nition • Data t ransfer ra te support : USB 2.
4 Chapter 1 Block Diagram.
Chapter 1 5 System Components This section is a virtual tour of th e sy stem’s interior and exterior components. Front Panel No. Component 1 USB 2.0 ports 2A c e r l o g o 3 Optical drive button 4 O.
6 Chapter 1 Rear Panel No. Component 1 Power connector 2 PS2 keyboard port 3V G A p o r t 4 USB 2.0 ports 5M i c - i n 6 Line-out 7 Expansion slot (graphics card and TV tuner card and Mode card) 8 Line-in 9 USB 2.
Chapter 1 7 Hardware Specifications and Configurations Processor BIOS IOS Hotkey List Main Board Major Chips Item Sp ecification Processor T ype CPUs which complaint with Intel FSB 800/1066/1333 MHz CPUs Socket T ype Intel Socket T LGA 1 156 pin Minimum operating speed 0 MHz (If S top CPU Clock in Sleep St ate in BIOS Setup is set to Enabled.
8 Chapter 1 Memory Combinations System Memory Audio Interface Slot Memory T o t al Memory Slot 1 1GB,2GB,4G 1G ~4GB Slot 2 1GB,2GB,4G 1G ~4GB Slot 3 1GB,2GB,4G 1G ~4GB Slot 4 1GB,2GB,4G 1G ~4GB Maximu.
Chapter 1 9 SATA Interface USB Port Environmental Requirements Power Management • Devices wake up from S3 should be le ss th an . • Devices wake up from S5 should be less than 10 seconds.
10 Chapter 1 Power Management Function(ACPI support function) Device Standby Mode • Independent power management ti me r for hard disk dr ive devices(0-15 minutes,time step= 1minute). • Hard Disk drive goes into S tandby mode(for A T A standard interface).
Chapter 2 11 CMOS Setup Utility CMOS setup is a hardware configurat ion program built into the system ROM, called the complementary meta l- oxide semiconductor (CMOS) Setup Utility . Since mo st systems are already properly configured and optimized, there is no need to run this util ity .
12 Chapter 2 Entering CMOS setup 1. T urn on the server and the monitor . If the server i s already turned o n, close all open app lication s, then restart the server . 2. During POST , press Delete . If you fail to press Delete before POST is completed, you will need to restart the server .
Chapter 2 13 Setup Utility Menus The Setup Main menu includes the following main setup categories. In the descrip tive table foll ow i n g ea ch of th e me nu sc re en sh ot s, settings in boldface are the default and suggested settings.
14 Chapter 2 Product Information The Product Information menu disp lays basic information about the syst em. These entries are for your reference only and are not user-configurable. Parameter Description Processor T ype T ype of CPU installed on the syst em.
Chapter 2 15 Standard CMOS Features Parameter Description Option System Date Set the date following the weekday-month-day-year format. System T ime Set the system time following the hour-minute-secon d format. Halt On Determines whether the system will stop for an error during the POST .
16 Chapter 2 Advanced BIOS Feature Parameter Description Option Quick Boot Allows you to decrease the time it takes to boot the computer by shortening or skipping certain standard booting process. Enabled Disabled Quiet Boot When enabled, the BIOS splash screen displays during startup.
Chapter 2 17 Advanced Chipset Features Parameter Description Option Intel EIST When enabled, this feature allows the OS to reduce power consumption. When disabled, the system operates at maximum CPU speed.
18 Chapter 2 Integrated Peripherals Parameter Description Option Onboard SA T A Controller Enables or disabl es the onboard SA T A controller. Enabled Disabled Onboard SA T A Mode Select an operating mode for the onboard SA T A. RAID Native IDE Onboard USB Controller Enables or di sables the onboard USB controller .
Chapter 2 19 Power Management Setup Parameter Description Option ACPI Suspend Mode Select an ACPI state. S3 (STR) S1 (POS) Deep power off mode Select the Deep power off Mode Enabled Disabled Power On .
20 Chapter 2 PC Health Status Parameter Description Option Smart F AN Enables or disables the smart system fan control function. Enabled Disabled.
Chapter 2 21 Frequency/Voltage Control Parameter Description Option Clock to All DIMM/PCI Enables or disabl es control the clock to all DIMM/PCI Enabled Disabled S pread S pectrum Enables or disables the reduction of the mainboard’s EMI. Note: Remember to disable the Spread S pectrum feature if you are overclocking.
22 Chapter 2 BIOS Security Features Setting a supervisor password 1. Use the up/down arrow keys to select Chan ge Supervisor Pa sswor d menu then press Enter . A password box will appear . 2. T ype a password then press Enter . The password may consist up to six al phanumeric characters (A-Z, a-z, 0-9) 3.
Chapter 2 23 Load Default Settings The Load Default Settings menu allows you to lo ad the defau lt settings for all BIOS setup parameters. Setup defaults are quite demanding in terms of resources cons umption.
24 Chapter 2 Save & Exit Setup The Save & Exit Setup me nu all ows you to save cha nges made and close the Setup Utility ..
Chapter 2 25 Exit Without Saving The Exit Without Saving menu allows you to disca rd changes made and close the Setup Utility ..
Chapter 3 26 This chapter contains step-by-step procedure s on how to disassemble the desktop computer for ma intenance and troubleshooting. Disassembly Requirements T o disassembl e the computer , yo.
27 Chapter 3 Pre-disassembly Procedure Before proceeding with the disassembly procedure, perform the steps listed below: 1. T urn off the system and all the peripherals conne cted to it. 2. Unplug the power cord from the power ou tl ets. 3. Unplug the power cord from the system.
Chapter 3 28 Removing the Side Panel 1. Remove the two screws located on the rear edge of the side panel. 2. Slide the side panel toward the back of the cha ssis until the tabs on the cover disengage with the slots on the chassis. 3. Lift the side panel away from the server and put it aside for reinstallation later .
29 Chapter 3 Removing the Heat Sink Fan Assembly W ARNING: The heat sink becomes very hot when the system is on. NEVER touch the heat sink with any metal or with your hands. 1. disconnect the fan cable fro m the mainboard. 2. Use a long-nosed screwdriver to loos en the four screws on the heat sink, in the order as shown below .
Chapter 3 30 Removing the Processor IMPORT AN T : Before removi ng a processor from the mainboard, make sure to create a backup file of all import ant dat a. W ARNING: The processor becomes very hot when the system is on. Allow it to cool off first before handling .
31 Chapter 3 Removing the VGA Card 1. Release the Slot cover lock. 2. Remove the screw from chassis. 3. Disconnect the power cables from the VGA card. 4. One finger Press the clip and the same time Gently pull the card to remove it from the mainboard.
Chapter 3 32 Removing the TV Card 1. Gently pull the TV card to remove it from the mainboard..
33 Chapter 3 Removing the Mode Card 1. Gently pull the Mode card to remove it from the mainbo ard..
Chapter 3 34 Removing the Hard Disk Drive 1. Disconnect the data and power cab les from the rear of the optical drive and th e mainboard. 2. Remove the HDD bracket a. Remove the screw that secures th e HDD bracket to the ODD bracket. b. Lift the bracket up and turn it over .
35 Chapter 3 3. Remove the HDD module a. Remove the eight screws secure the HDD module to the HDD bracke t. b. Slide the HDD out of the bracket..
Chapter 3 36 Removing the Front Bezel 1. Disconnect the LED cable. 2. Release the front bezel from the chassis interior . 3. Pull the bezel away from the chassis.
37 Chapter 3 Removing Rear USB Board 1. Remove USB cable 2. Release the screw of rear usb. 3. Remove the rear usb board..
Chapter 3 38 Removing the Cables 1. Remove power switch and LED cables from slot of M/B 2. Remove HDD Data and ODD Data cables from slot of M/B. 3. Remove USB1/2/3 cable from M/B.
39 Chapter 3 Remove System FAN 1. Remove System F AN cable from M/B. 2. Release four screws according to the following picture. 3. T ake off the system fan from chassis.
Chapter 3 40 Removing the Optical Drive 1. Disconnect the data and power cables from the rear of the optical drive. 2. Remove Four screw from the optical drive.
41 Chapter 3 Removing the Power Supply 1. Disconnect the 24-pin and 4-pin power supply ca bles from the mainboard . 2. Remove the four screw that secure s the power supply to the chassis.
Chapter 3 42 Removing the Memory Modules IMPORT AN T : Before removing any DIMM from the memory board, make sure to create a backup file of all import ant dat a. 1. Press the holding clips on both sides of t he DIMM slot outward to release the DIMM. 2.
43 Chapter 3 Removing the removable HDD bay 1. Remove the HDD rail 2. Remove the screws that secure the HDD bay . 3. Remove the HDD bay ..
Chapter 3 44 Removing the Mainboard 1. Remove the eight screws that secure the mainb oard to the chassis. Note: Circuit boards >10 cm² has been highlig hted with the yellow rectangle as above image shows. Please detach the Circuit boards and foll ow local regulations for disposa l.
45 Chapter 3 2. Lift the board from the chassis. 3. Remove the RTC battery ..
Chapter 4 46 This chapter provides instructions on how to troubleshoot system hardw are problems. Hardware Diagnostic Procedure IMPORT AN T : The di agno stic tests described in this chapter are only intended to test Acer products. Non- Acerproducts, prototype cards, or modified options can give false errors and inval id systemresponses.
47 Chapter 4 System Check Procedures Power System Check If the system will power on, skip this sect ion. Refer to System External In spection. If the system will not power on, do the fol lowi ng: • Check if the power cable is properly co nnected to the system and AC source.
Chapter 4 48 Beep Codes Beep codes are used by the BIOS to indicate a seriou s or fatal error to the end user . Beep codes are used when an error occurs before the system video ha s been initialized. Beep c odes will be generated by the system board speaker , commonly referred to as the PC speaker .
49 Chapter 4 Checkpoints A checkpoint is either a byte or word value output to I/O port 80h.The BIOS outputs checkp oints throughout bootblock and Power-On Self T est (POST) to indicate th e task the system is currently executing.
Chapter 4 50 DA Restore CPUID value back into register . Give control to BIOS POST (ExecutePOSTKernel). See POST Code Checkpoints section of document for more information. DC System is waking from ACPI S3 st ate. E1-E8 EC- EE OEM memory detection/configuration error.
51 Chapter 4 Bootblock Recover y Code Checkpoints The Bootblock recovery code gets control when the BIOS determines that a BIOS recovery needs to occur because the user has forced the upda te or the BIOS checksum is corrupt . The following table describes the type of checkpoints that may occur during th e Bootblock recovery portion of the BIOS.
Chapter 4 52 BIOS Recovery 1. This function only effects when the BIOS BootBlock section is healthy . 2. Allow to execute recovery function media: FDD / USB storage / ODD. 3. The recovery media to support Boot fu nction is unnecessary . 4. Recovery step as follow: 4-1.
Chapter 5 53 M/B Placement Jumper and Connector Information Chapter 5.
54 Chapter 5 LABEL COMPONENTS 1. CPU Socket Supports the LGA1 156 Intel Lynnfield/Havendale/Clarkdale processors 2. CPU_F AN CPU cooling fan connector 3. DIMM1~4 240-Pin DDR3 SDRAM slots(Chann el A: DIMM4, DIMM2 Channel B: DIMM3, DIMM1) * Single Channel Mode: DIMM2 must be populated.
Chapter 5 55 Jumper Setting The section explains how to set jumper fo r correct configuration of the mainboard. Setting Jumper Use the motherboard jumpers to set system config uration options. Jump ers with more Than one pin are numbered. When setting the jumpers, ensure th at the jump er caps are Placed on the correct pins.
56 Chapter 5 Connecting Optional Devices Refer to the following for information on connecting the mo therboard’s optional devices: SATA1~6: Serial ATA connectors These connectors are used to support the new Serial A T A devices for the highest data transfer rates (3.
Chapter 5 57 have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard. Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
58 Chapter 5 C_INTRUSION: Chassis detect header This detects if the chassis cover has been removed. This function needs a chassis equipped with intrusion detection switch and needs to be enabled in BIOS.
Chapter 5 59 TPM: TPM Module Header This header allows user to protect the PC from impermissible visit. SPI_DEBUG: SPI_DEBUG header 9 PD7 10 ACK 1 1 BUSY 12 PE 13 SLCT 14 ALF 15 ERROR 16 INTT 17 SLCTI.
60 Chapter 5 GPIO0~1: Button recovery jumper 5 VCC 6 CLK 7 GND 8 DO Pin Signal Name 1G P 3 6 ( G P 1 6 ) 2G N D Pin Signal Name Pin Signal Name.
chapter 6 61 This chapter offers the FRU (Field Replaceable Unit) list in global config uration of the Aspire M5910(G) desktop computer . Refer to this chapter whenever orderin g the parts to repair or for RMA (Return Merchandise Authorization).
62 Chapter 6 Aspire M5910(G) Exploded Diagram(AM551 ASSY) NOTE: This section will be updated when more information becomes availab le. ITEM NAME Q’TY ITEM NAME Q’TY 1 CHASSIS ASM 1 5 FRONT BEZEL 1.
Chapter 6 63 Aspire M5910(G) Exploded Diagram(AM550 ASSY) NOTE: This section will be updated when more information be comes availa ble. ITEM NAME Q’TY ITEM NAME Q’TY 1 CHASSIS ASM 1 5 FRONT BEZEL .
64 Chapter 6 Aspire M5910(G) FRU List Components Model Name or Key Spec. Acer P/N MB Kit MB Kit aSampras EIH57MK for M5 Intel H57 Realtek RTL81 1 1E Giga LAN A TX W/O 1394 LF w/i D-Sub port MB.SDW07.002 Chassis Hon Hai Chassis MicroA TX HM 090H with front USB 4 port for Aspire AM550 bezel HS.
Chapter 6 65 CPU CPU Intel Core i7 870 LGA 2.93G 8M 1333 1 156 95W B-1 Quad Core KC.87001.CI7 CPU Intel Core i7 860 LGA 2.8G 8M 1333 1 156 95W B-1 Quad Core KC.86001.CI7 CPU Intel Core i5 750 LGA 2.66G 8M 1333 1 156 95W B-1 KC.75001.CI5 CPU Intel Core i5 670 LGA 3.
66 Chapter 6 ODD TOSHIBA DVD-ROM HH DL 16X TS-H353C LF Black Bezel SA T A (HF+Win7) KV .01601.001 GH-41F(H/F) Win7 non-Labelflash KU.0160D.049 DH-16AASH (H/F) Win7 non- Labelflash KU.0160F .009 ODD TOSHIBA Super-Multi DRIVE HH DL 16X TS-H653G LF Black Bezel SA T A (HF+Win7) KU.
Chapter 6 67 Lite-On PCI Modem card, D-1 156I#/A7A, LSI Universal Modem (PCI) 56K V .92 - Pinball ( P40) FX.10100.004 WLAN WP81R1, WLAN PCI Card 802.1 1b/g/n 1T x 2R, Realtek RTL8190 NI.10200.021 WN7600R, WLAN PCI-Ex1 card 802.1 1 b/g/n 1T x 2R, Ralink 1T x 2R, RT2790+R T2720 NI.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Acer M5910(G) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Acer M5910(G) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Acer M5910(G), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Acer M5910(G) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Acer M5910(G), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Acer M5910(G).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Acer M5910(G). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Acer M5910(G) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
