Manuel d'utilisation / d'entretien du produit R501PC du fabricant Sony
Aller à la page of 52
1 MZ-R501/R501PC SERVICE MANUAL Model Name Using Similar Mechanism MZ-R500 Mechanism T ype MT -MZR500-172 Optical Pick-up Name LCX-4R System Audio playing system MiniDisc digital audio system Laser diode properties Material: GaAlAs Wa v elength: λ = 790 nm Emission duration: continuous Laser output: less than 44.
2 Flexible Cir cuit Board Repairing • Keep the temperature of the soldering iron around 270°C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering.
3 1. SERVICING NOTE ......................................................... 4 2. GENERAL Looking at the Controls ...................................................... 5 3. DISASSEMBL Y 3-1. Case (Lo wer) Assy .......................................
4 MZ-R501/R501PC SECTION 1 SERVICING NOTE NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc.
5 MZ-R501/R501PC SECTION 2 GENERAL This section is extracted from instruction manual. Looking at the contr o ls S e e p a ge s in ( ) for more de t ails.
6 MZ-R501/R501PC 3-1. CASE (LOWER) ASSY (P age 6) 3-2. CASE (UPPER) ASSY (P age 6) 3-4. MAIN BOARD (P age 7) 3-5. MD MECHANISM DECK (P age 8) 3-6. SER VICE ASSY , OP (P age 8) 3-7. HOLDER ASSY (P age 9) SET 3-10. DC MO TOR (M601) (P age 10) 3-3. LCD MODULE (P age 7) 3-9.
7 MZ-R501/R501PC 3-3. LCD MODULE 3-4. MAIN BOARD 1 screws (1.7x3), tapping 4 LCD module claws case (upper) ass y 2 screws (1.7x3), tapping 3 3 screws (M1.
8 MZ-R501/R501PC 3-5. MD MECHANISM DECK 3-6. SER VICE ASSY , OP 1 screws (1.7), MI 2 chassis assy , se t boss 3 MD mechanism deck 4 spring (S), rack 6 spring, thrust detent 3 precision pan screw (M1.4) 5 precision pan screw (M1.4) 1 washer (0.8 - 2.5) 2 gear (SA) 8 Pull off the lead screw .
9 MZ-R501/R501PC 3-7. HOLDER ASSY 3-8. MOTOR FLEXIBLE BOARD 4 Remov e the holder assy to direction of the arrow B . 1 Open the holder assy . A 2 B 3 boss 2 Remov e two solders of DC motor (ov er write head up/down) (M603). 1 Remov e four solders of DC motor (sled) (M602).
10 MZ-R501/R501PC 3-9. DC MOT OR (M602) 3-10. DC MOTOR (M601), DC MOT OR (M603) 4 two precision pan screws (M1.4) 5 DC motor (sled) (M602) 1 Remov e four solders of motor flexib le board. 2 washer (0.8 - 2.5) 3 gear (SA) 1 Remov e six solders of motor flexib le board.
11 MZ-R501/R501PC 2 In the normal mode, turn on the [HOLD] switch. While press- ing the [VOL - -] key press the following order: > t > t . t . t > t . t > t . t X t X SECTION 4 TEST MODE 4-3. Operation in Setting the T est Mode • When the test mode becomes active, first the display check mode is selected.
12 MZ-R501/R501PC 4-5. Configuration of T est Mode 4-6. Manual Mode Mode to adjust or check the operation of the set by function. Normally , the adjustment in this mode is not executed.
13 MZ-R501/R501PC 4-8. Self-Diagnosis Result Display Mode This set uses the self-diagnostic function system in which if an error occurred during the recording or playing, the mechanism control block and the power supply control block in the microcomputer detect it and record its cause as history in the nonvolatile memory .
14 MZ-R501/R501PC • Description of Indication History History code number Description 1 The first error N The last error N1 One error before the last. N2 T wo errors before the last. R_ T otal recording time 4-9. Reset the error display code After servicing, reset the error display code.
15 MZ-R501/R501PC 4-1 1. Key Check Mode This set can check if the set function normally . • Setting Method of Key Check Mode 1. Setting the test mode (see page 11). 2 . Press the [T.MARK] + X ke ys activ ates the key check mode. (At the last two digits, AD v alue of remote commander key line is displayed in hexadecimal) 3.
16 MZ-R501/R501PC 4. When all the keys on the set and on the remote commander are considered as OK, the following displays are shown for 4 sec- onds. Example1: When the keys on the set are considered as OK: 5. When all keys were checked or if the upper panel is opened, the key check mode quits and the test mode (display check mode) comes back.
17 MZ-R501/R501PC • Setting method of NV reset 1. Select the manual mode of the test mode, and set item number 021NV Reset (see page 12). 2. Press the X key . 3. Press the X key once more. 4. Press the x key to quit the manual mode, and activate the test mode (display check mode).
18 MZ-R501/R501PC • Setting method of power supply manual adjustment 1. Make sure that the power supply voltage is 3V . 2. Set the test mode (see page 11). 3. Press the . or [VOL- -] key to activate the overall adjustment mode. 4 . Press the [END SEARCH] ke y .
19 MZ-R501/R501PC 3. Adjust with [VOL +] , [VOL - -] key so that the adjusted value (hexadecimal value) becomes the ambient temperature. (Initial value: 14h = 20 ° C, Adjusting range: 80h to 7fh ( – 128 ° C to +127 ° C) 4. Press the X key to write the adjusted value.
20 MZ-R501/R501PC 8. Press the N key , and set the laser CD read adjustment mode (item number 012). 9. Press the [ENTER] key and set the address & adjusted value display (see page 13). 10. Check that the laser power meter reading is 0.97 ± 0.10 mW .
21 MZ-R501/R501PC 8. If OK through the overall MO adjustments, press the x key to return to the test mode and terminate the Overall Adjustment mode. 6. Insert MO disc in the set, and press the > key to set the Overall MO Adjustment mode. Automatic adjustments are made.
22 MZ-R501/R501PC • Overall CD and MO adjustment items 1. Overall CD adjustment items Item No. Description 312 313 CD electrical offset adjustment 314 321 CD tracking error gain adjustment 328 CD TW.
23 MZ-R501/R501PC 2. Adjust with the [VOL+] key (adjusted value up) or [VOL- -] key (adjusted value down) so that the adjusted value becomes S67. 3. Press the X key . 4. Set item number 868 (see page 12). 5. Adjust with the [VOL+] key (adjusted value up) or [VOL- -] key (adjusted value down) so that the adjusted value becomes S01.
24 MZ-R501/R501PC SECTION 6 DIAGRAMS 6-1. IC PIN FUNCTION DESCRIPTION • IC501 SN761057DBT (RF AMP , FOCUS/TRA CKING ERROR AMP) Pin No. Pin Name I/O Description 1T EO Tr acking error signal output to.
25 MZ-R501/R501PC • IC801 CXD2671-204GA (SYSTEM CONTROLLER, DIGIT AL SIGNAL PROCESSOR, 16M BIT D-RAM) Pin No. Pin Name I/O Description 1P A USE KEY I Set key input terminal ( X key input) 2 (MIC SEN.
26 MZ-R501/R501PC Pin No . Pin Name I/O Descr iption 52 A VD2 — Po wer supply terminal (for the analog) (+2.4 V) 53 A VS2 — Ground terminal (for the analog) 54 ADRB I A/D converter the lower limit.
27 MZ-R501/R501PC Pin No. Pin Name I/O Description 99 SLDW O Sled motor dri ve signal output (W) to the motor dri ver (IC701)/driv e control signal output (2+) 100 SLCU I Spindle motor driv e comparis.
28 MZ-R501/R501PC Pin No. Pin Name I/O Description 169 CLK SEL O System clock select signal output to the power control (IC901) 170 OPEN CLOSE SW I Open/close detection switch (S806) of the upper pane.
MZ-R501/R501PC 29 29 Pin No. Pin Name I/O Descr iption 223 SPDL MON I Spindle servo monitor signal input 224 to 226 (XA VLS), (SOUND 1, 2) I Not used (open) 227 XHOLD SW I HOLD switch (SW801) input te.
MZ-R501/R501PC 30 30 33 24 81 35 25 80 TRACKING COIL DRIVE 10 19 82 8 18 83 FOCUS COIL DRIVE 14 17 42 16 233 98 SLED VOLTAGE MONITER SPINDLE SERVO DRIVE SWITCH IC805 41 12 20 97 29 26 99 MAIN BOARD (1.
MZ-R501/R501PC 31 31 9 1 3 2 71 AUDIO I/F CONTROLLER AUDIO I/F CONTROLLER CLOCK DIVIDER OPT CONTROL SWITCH Q302 A/D CONVERTER & HPF IP GAIN AMP 29 30 215 192 191 218 240 142 22 21 15 2 4 24 23 13 .
MZ-R501/R501PC 32 32 187 206 205 1 13 14 227 170 230 3 48 10 20 86 10 25 169 236 235 234 17 18 19 S805 (HALF LOCK) 15 21 141 164 165 8 11 39 36 12 34 32 50 33 4 7 56 54 52 55 1 3 2 5 53 14 13 10 11 4 .
MZ-R501/R501PC 33 33 Common note on Printed Wiring Board: • Y : par ts extr acted from the conductor side. • : Pattern from the side which enables seeing.
MZ-R501/R501PC 34 34 1 A B C D E F G H I J 23456789 1 0 11 12 13 14 MAIN BOARD (SIDE A) R843 R823 R827 C824 R834 R808 C803 R804 C805 C826 C851 R603 C713 R925 C922 C306 C106 C206 R108 R109 R208 R209 C9.
MZ-R501/R501PC 35 35 1 A B C D E F G H I J 2 3 4 5 6 7 8 9 10 11 12 13 14 L904 D201 D906 1 2 3 5 4 1-680-275- J901 DC IN 3V ! i MAIN BOARD (SIDE B) C828 R833 C514 C806 R806 R807 C505 R510 C513 C521 R8.
MZ-R501/R501PC 36 36 IC B/D IC B/D IC B/D C523 C516 IC501 L502 Q603 IC601 C621 L501 TP TP L601 CN501 AP501 AP502 AP503 AP504 AP522 L602 TP512 Q501 TP603 TP602 AP506 TP511 TP518 TP519 TP520 C501 C502 R.
MZ-R501/R501PC 37 37 IC B/D (EXCEPT US, CND MODEL) (US, CND MODEL) S806 X801 D903 C814 C801 C823 C812 C813 C802 L802 C820 C819 C810 C811 S803 L801 C818 C822 C821 FB803 S805 C809 IC901 C803 IC805 D901 .
MZ-R501/R501PC 38 38 IC B/D IC B/D J301 IC302 C320 R306 R207 R107 C315 R203 R103 C316 R106 R206 C314 R303 FB303 R307 L301 C202 C102 R202 R102 C312 FB302 FB304 C311 R105 R205 Q302 IC301 D101 D201 TP308.
39 MZ-R501/R501PC • IC BLOCK DIAGRAMS IC501 SN761057DBT 1 TE REXT Wpp LPF VREF C D D-C Iy Ix Jx Jy A A-C B ADIP-IN FE ABCD OFC-1 OFC-2 PS LP EQ AGND RF OUT CCSL2 VC XRST SCK SBUS VREF075 PEAK BOTM D.
40 MZ-R501/R501PC IC701 SC111257FCR2 43 PRE DRIVER PRE DRIVER + – 48 47 44 45 46 49 50 51 + – 52 + – 53 54 55 56 1 2 3 4 5 42 41 39 37 38 40 + – + – 6 3PHASE CONTROL 35 34 33 36 31 30 29 32 .
41 MZ-R501/R501PC 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 54 55 56 1 53 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 23 25 26 27 28 VB BATM CHGSW RS INP2 I.
42 MZ-R501/R501PC V REF MT SW BST SW BEEP 19 20 21 22 23 24 18 17 16 15 14 13 PW SW 12 11 10 8 7 BST1 9 BST2 6 5 4 3 2 1 BST AGC PW B PW A ADD TCMT VCC IN R IN L OUTB OUTA +B OUT L PW GND OUT R DET AG.
43 MZ-R501/R501PC SECTION 7 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
44 MZ-R501/R501PC 7-2. CHASSIS SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 52 53 54 55 57 55 56 58 59 60 61 62 63 64 MT -MZR500-172 51 X-3379-969-1 CHASSIS ASSY 52 3-318-382-01 SCREW (1.7X3), T APPING 53 4-218-233-11 SCREW (1.
45 MZ-R501/R501PC 7-3. MD MECHANISM DECK SECTION (MT -MZR500-172) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark M603 M601 M602 101 102 105 106 107 108 109 115 121 120 119 1.
46 MZ-R501/R501PC SECTION 8 ELECTRICAL P AR TS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may hav e some difference from the original one.
47 MZ-R501/R501PC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN C705 1-135-211-11 T ANT AL. CHIP 6.8uF 20% 6.3V C706 1-135-211-11 T ANT AL. CHIP 6.8uF 20% 6.3V C707 1-104-912-11 T ANT AL. CHIP 3.3uF 20% 6.3V C708 1-119-749-11 T ANT AL.
48 MZ-R501/R501PC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN @ Replacement of CXD2671-204GA (IC801) used in this set requires a special tool.
49 MZ-R501/R501PC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN R801 1-218-990-11 SHORT 0 R804 1-218-990-11 SHORT 0 R805 1-218-981-11 RES-CHIP 220K 5% 1/16W R806 1-208-927-11 MET AL CHIP 47K 0.5% 1/16W R807 1-208-927-11 MET AL CHIP 47K 0.
50 MZ-R501/R501PC Ref. No. Part No. Description Remark ACCESSORIES ************ 0 1-418-784-11 ADAPTOR, AC (AC-MZR55) (CH) 0 1-476-857-11 ADAPTOR, AC (AC-ES305) (AEP ,FR,EE) 0 1-476-858-11 ADAPTOR, AC.
51 MZ-R501/R501PC MEMO.
52 MZ-R501/R501PC REVISION HIST OR Y Clicking the ver sion allows y ou to jump to the re vised page. Also, clicking the v ersion at the upper on the revised pa ge allo ws you to jump to the next re vised page. Ve r. Date Description of Revision 1.0 2001.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sony R501PC c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sony R501PC - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sony R501PC, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sony R501PC va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sony R501PC, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sony R501PC.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sony R501PC. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sony R501PC ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
