Manuel d'utilisation / d'entretien du produit LIFESTULER SYSTEM 40 831.15931 du fabricant Sears
Aller à la page of 24
s Rs! Model No. 831.159310 Serial No. The serial number can be found in the location shown below. Write the serial number in the space above. Serial Number Decal CAUTION! Read all of the safety precau.
TABLE OF CONTENTS IMPORTANT SAFETY PRECAUTIONS ................................................. 2 BEFORE YOU BEGIN ............................................................... 3 ASSEMBLY.. ..........................................................
BEFORE YOU BEGIN Congratulations for selecting the SEARS LIFESTYLER e SYSTEM 40 cross training system. The innov- ative LIFESTYLER SYSTEM 40 offers an impressive array of weight training and aerobic exercises to let you enjoy true cross training workouts in the convenience of your home.
ASSEMBLY Assembly requires two people and will take about 4 hours. The following tools (not Included) are required: two 8" adjustable wrenches, a rubber mallet, a phillips screwdriver and a standard screwdriver. Grease and a small bowl of soapy water are also required.
o . , . Slide the Front Upright (76) over the two 5/16" x 2 1/2" Carriage Bolts (22) in the Base (69). Attach the Front Upright with two 5/16" Nylock Nuts (4). Do not fully tighten the Nylock Nuts until completeing step 24. Place the Top Brace (86) on top of the Front and Rear Uprights (76, 74).
8. 8 g. Press two 1 3/4" x 1 3/4" Inner Caps (28) into each of the Arms (51). Apply grease to the axles On the Arm Support (85). Slide an Arm (51) onto the right axle. Hold two 1 5/16" Retainer Rings (38) and a 1" Plastic Cap (37) against the lower end of the axle.
10. Attach a 3 1/2" "U" Bracket (98) to the left Arm (51) with a 5/16" x 2 1/2" Bolt (20), 3/8" Washer (8) and 5/16" Nylock Nut (4). Do not overtighten the Nylock Nut--the "U" Bracket must be able to pivot freely.
14, Place a Foot Pad (62) on the end of the Right Pedal (64). Attach the Foot Pad with a 1/2" Pan Screw (45). Attach the other Foot Pad (62) to the Left Pedal (63) in the same manner. 15. Apply grease to the cylinder axles on the Rear Upright (74).
18. Attach a VKR Armrest (58) to each VKR Arm (57) with two 1/4" x 2' Screws (9) and 1/4" Washers (1). Attach the VKR Backrest (59) to the Rear Upright (74) with two 1/4" x 2 1/2" Screws (2) and 1/4" Washers (1). 19. Press a 1" Round Inner Cap (11) into each end of a Handle (52).
10 22. Attach the Backrest (78) to the Front Upright (76) with two 1/4" x 2 1/2" Screws (2) and 1/4" Washers (1). 23. Insert a 3/8" x 2 3/4" Bolt (16) into one side of the Top Brace (86). Slide a 3/8" x 3/8" Metal Spacer (6) onto the Bolt.
26. Route the end of the Short Cable (94) around the indicated 3 1/2" Pulley (55) in the "t" Plates (75). Insert a 3/8" x 2 3/4" Bolt (16) into one side of the Top Brace (86). Slide a 3/8" x 3/8" Metal Spacer (6) onto the Bolt.
29. 29 12 Attach a 3" "U" Bracket (97) to the Front Upright (76) with a 5/16" x 4" Bolt (27), 5/16" Washer (10) and 5/16" Nylock Nut (4). The Nylock Nut should be threaded onto the Bolt four complete turns. The cabling will be too short If the Nylock Nut Is overtlght- ened.
33. Attach a Thick "L" Bracket (100) to the bracket on the Top Brace (86) with a 5/16" x 3 1/4" Bolt (19) and 5/16' Nylock Nut (4). Make sure that the Thick "L" Bracket is turned as shown. Slide a Plastic Cable Guide (18) and a 3 1/2" Pulley (55) onto a 3/8" x I 3/4" Bolt (26).
14 37. Slide the end of the Long Cable (93) onto the end of the 3/8" x 3 1/2" Bolt (5) in the Top Brace (86). Slide a 3/8" Washer (8) onto the Bolt and tighten the 3/8" Jam Nut (7) onto the Bolt. Note'- The 3/8" x 3 1/2" Bolt (5) Is the Bolt that was used In assembly step 24.
41. Raise the Weight Selector (82). Place the remaining nine Weights (79) on the Weight Guides (83) by tipping the Weights as shown. Make sure that the Weights are turned so all of the pin grooves are under the Weights and are on the same side. Lower the Weight Selector into the Weights.
16 45. Press a 1" Round Inner Cap (11)into each end of the I.at Bar (87). 46. 47, Remove the "HIGH PULLEY" decal from the Decal Sheet (not shown). Apply the decal to the side of the Top Brace (86). Remove the "DUAL FUNCTION PRESS ARM" decal from the Decal Sheet (not shown).
49. Remove the "TRIAD LEG SYSTEM" decal from the Decal Sheet (not shown). Apply the decal to the corner of the Leg Press Plate (70). 50. Remove the ten small decals numbered "10" through "100" from the Decal Sheet (not shown).
52. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in USING THE LIFESTYLER SYSTEM 40, beginning on page 19 of this owner's manual.
USING THE LIFESTYLER SYSTEM 40 The instructions below describe how each part of the cross training system can be adjusted. See the EXERCISE GUIDE accompanying this owner's manual to see how the cross training system should be set up for each individual exercise.
USING THE ARMS IN THE BUTrERFLY MODE To use the Arms (51) in the butterfly mode, the Arm Support (85) must be locked in a stationary position. To lock the Arm Support, insert a 4 1/2" "L" Pin (43) down through the center of the Arm Support and the bracket on the Front Upright (76).
TROUBLE-SHOOTING AND MAINTENANCE Inspect and properly tighten all parts of the cross training system each time you exercise. Replace any wom parts immediately. The cross training system can be cleaned using a damp cloth and mild non- abrasive detergent.
PART LIST/EXPLODED DRAWING--Model No. 831.159310 Key Part Key Part No. No. Qty. Description No. No. Qty. Description 1 014127 10 1/4" Washer 53 112444 2 Handle Grip 2 013341 4 1/4" x2 1/2&qu.
84 55 55 44 28 I 6 14 |15_ 97 54 > 42 4 86 87 23 42 4 10 33 55 20 I I i I I I I 4 58 57 47 s 48 61 10 39 39 37 73 69 16 45 23.
ORDERING REPLACEMENT PARTS Each SYSTEM has its own MODEL NUMBER. Always mention this MODEL NUMBER when request- ing service or repair parts for your SYSTEM. All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and most SEARS RETAIL STORES.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sears LIFESTULER SYSTEM 40 831.15931 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sears LIFESTULER SYSTEM 40 831.15931 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sears LIFESTULER SYSTEM 40 831.15931, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sears LIFESTULER SYSTEM 40 831.15931 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sears LIFESTULER SYSTEM 40 831.15931, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sears LIFESTULER SYSTEM 40 831.15931.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sears LIFESTULER SYSTEM 40 831.15931. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sears LIFESTULER SYSTEM 40 831.15931 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
