Manuel d'utilisation / d'entretien du produit ST15230W/WD/WC du fabricant Seagate
Aller à la page of 40
HA WK 4 F amil y: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Wide Bus) ST15230W/WD/WC . . . . . . . . . . . . . . . . . . . . . . . ST15230DC . . . . . . .
Contents Introduction ........................................................... 1 Electromagnetic interference ................................ 1 Before you begin .................................................. 3 Installation overview ...........
Hawk 4 (Wide) Family Install Guide, Rev. A 1 ___________________________________________ Introduction Before attempting any installation, please read through all applicable sections of this document, including all warnings and cautions.
2 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ The physical design characteristics of the drive(s) described herein, serve to minimize EMI radiation when installed in an enclosure that provides reason- able shielding.
Hawk 4 (Wide) Family Install Guide, Rev. A 3 ___________________________________________ Before you begin Verify that the system is switched off and discon- nected from main power before any installation is attempted. Protect yourself, the drive, and your valuable pro- grams and data by reading the following cautions and warnings.
4 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ • Inspect drive for possible shipping damage. All claims of this type should be filed promptly with the trans- porter involved. Save original packing materials to be used when reshipping.
Hawk 4 (Wide) Family Install Guide, Rev. A 5 ___________________________________________ To insure optimum reliable equipment op- eration, it is required that technical support personnel discharge the.
6 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Safety instructions 1. The disc drive(s) are to be installed in a customer supplied enclosure where the surrounding air does not exceed 50 o C. 2. Four (4) 6-32 UNC-2A screws are required for installation.
Hawk 4 (Wide) Family Install Guide, Rev. A 7 ___________________________________________ Sicherheitsanleitung 1. Däs Gerät ist ein Einbaugerät, vorgesehen für eine maximale Umgebungstemperatur von 50 o C. 2. Zur Befestigung der Drive werden 4 Schrauben benötigt (6-32 UNC-2A).
8 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Installation Overview Installation of the drive can be divided into distinct phases as outlined below. Some of these may not be applicable to your particular installation requirements.
Hawk 4 (Wide) Family Install Guide, Rev. A 9 ___________________________________________ • Low-level formatting: After the drive has been properly configured for the system, it does not need to be low-level formatted, as this has been done by the factory and does not require this step during installation.
10 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Product repair information Service requirements The special facilities required for the manufacture of these drives generally prohibit repair in the field. If problems occur during installation, please contact your supplier for assistance.
Hawk 4 (Wide) Family Install Guide, Rev. A 11 ___________________________________________ Shipping: When transporting or shipping a drive, a Seagate approved container must be used. Keep your original box. They are easily identified by the Seagate Approved Package label.
12 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ If the drive is no longer under warranty contact pur- chase source for repair information or refer to numbers listed in the following paragraph . Technical support services Please contact your dealer for technical support and installation troubleshooting.
Hawk 4 (Wide) Family Install Guide, Rev. A 13 ___________________________________________ SeaTDD: 408/438-5382 TDD is a Telecommunication Device for the Deaf where two people can communicate using a keyboard that is connected to the phone line. A TDD device is required to access this service.
14 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ With this service you can access: • Specifications and jumper configurations for all Seagate products. • Reprints of Seagate documentation. • A directory of information and helpful utilities that you can download to your own computer.
Hawk 4 (Wide) Family Install Guide, Rev. A 15 ___________________________________________ Drive specifications Product Hawk 4 family (wide) Information ST15230W ST15230WD ST15230WC ST15230DC Interface.
16 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes. [1] Standard units are factory formatted with 512 data bytes per sector. ST15230 OEM standard models have twelve spare sectors per cylinder and 2 cylinders at inner tracks reserved for spares.
Hawk 4 (Wide) Family Install Guide, Rev. A 17 ___________________________________________ Initial setup information For the initial setup connect the cables, set the SCSI bus address and enable or disable (as required by system configuration), the SCSI I/O line terminator resistors (model "W" drives only).
DC Power Connector Pin 1P 2P 3P 4P Power +12V +12V ret + 5V ret + 5V J1 1P 2P 3P 4P 68 Pin SCSI I/O Connector J1-Auxiliary 18 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Figure 1.
Hawk 4 (Wide) Family Install Guide, Rev. A 19 ___________________________________________ If the drive LED shows no on/off activity when the host is trying to communicate with it, an incorrect bus address selection at the drive (or remote ID select location) should be suspected.
20 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Model numbers that end in "WD and DC" have differen- tial I/O circuits and these drives and "WC" model drives have no provisions for terminators on the drive PCB.
J1-Auxiliary Pin 1A 68 Pin SCSI I/O Connector J1-DC Power Pin 1P J6 J2 J1 Pin 1 J6 J2 Pin 1 80 Pin SCSI I/O and DC Power Connector Hawk 4 (Wide) Family Install Guide, Rev. A 21 ___________________________________________ Figure 2a.
22 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Drive configuration Each disc drive has option select header connectors on the back, side and front where jumper plugs are in- stalled to select the way that the drive is to be config- ured and to select its ID (0 - 15) on the I/O bus.
Hawk 4 (Wide) Family Install Guide, Rev. A 23 ___________________________________________ ST15230WC/DC family 80 pin SCSI I/O drives On Hawk 4 family, ST15230WC/DC model drives there is no J1-auxiliary. J6 can be used to set drive ID, but the host probably does it over the 80 pin interface.
J1-DC Power Connector J2 Drive Front Pin 1 End J6 SCSI I/O Connector J1- SCSI I/O Pin 1 J2 J1- Auxiliary See Figure 3b Drive with HDA up, PCB down, viewed from front Pin 1 HDA.
Figure 3b. Drive configurator Hawk 4 family ST15230W/WD model (Wide bus) J1-DC Power J1 68 Pin SCSI I/O Connector Drive HDA SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID.
Figure 3c. Drive configurator Hawk 4 family ST15230WC/DC model (Wide bus) Pin 1 J2 J1 J2 Drive Front Pin 1 End J6 Pin 1 HDA Drive with HDA up, PCB down, viewed from front J6 [1] Delay Motor S.
Hawk 4 (Wide) Family Install Guide, Rev. A 27 ___________________________________________ Notes for Figure 3a, 3b and 3c: [1] Notes explaining the functions of the various jump- ers on jumper header connectors J2, J1-auxiliary and J6 are given below in left to right order of jumper position.
28 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ [4] The drive time-shares the ID and LED functions of J6 and J1-auxiliary. That is, a cable may be at- tached to one of these headers to pick up the signal that lights the external LED indicator.
Hawk 4 (Wide) Family Install Guide, Rev. A 29 ___________________________________________ J2 Jumper. Position Jumper Function Description TE (Applies to "W" models only) On With the jumper installed, the optional on- board (non-removable) terminator circuits are enabled (connected to the I/O lines).
30 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ continued from previous page WP On Entire drive is write protected. Off Drive is not write protected. Default is no WP jumper installed. PE On Parity checking and parity error reporting by the drive is enabled.
Hawk 4 (Wide) Family Install Guide, Rev. A 31 ___________________________________________ continued from previous page TP TP (Not applicable to "WC and DC" model drives) Off Off No terminator power is connected to drive terminators or SCSI bus I/O pin 26.
32 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ J6 and J1-Auxiliary Jumper Installation Jumper Function Description A 3 ,A 2 ,A 1 ,A 0 * Drive ID on SCSI Bus.
Hawk 4 (Wide) Family Install Guide, Rev. A 33 ___________________________________________ Drive installation This section describes the physical mounting of the drive in the host cabinet and the logical installation as a system member, which is called drive setup.
Figure 4. Hawk 4 family ST15230W/WD model drive mounting dimensions (68 pin SCSI I/O connector) A F D E C [1] [3] B G J H K [2] Notes: [1] [2] [3] [4] Inches Millimeters 5.74 4.00 1.620 2.362 .620 4.000 .250 1.750 3.
Figure 5. Hawk 4 family ST15230WC/DC model drive mounting configuration dimension (80 pin I/O connector) A F D E C [1] [3] B G J H K [2] Notes: [1] [2] [3] [4] Inches Millimeters 5.74 4.00 1.620 2.362 .620 4.000 .250 1.
36 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Do not power up the host system until the drive is mounted and the system cover is replaced. • Connect DC power connector to the drive. (does not apply to "WC and DC" models which have DC power lines in the 80 pin I/O connector).
Hawk 4 (Wide) Family Install Guide, Rev. A 37 ___________________________________________ SCSI interface drives The SCSI interface handles both drive geometry and defect management internally. The "no drive installed" option is selected for systems with SCSI drives.
Seagate Technology, Inc. 920 Disc Drive Scotts Valley, CA. 95066-4544, USA Publication Number: 77767477, Rev. A Printed in USA.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Seagate ST15230W/WD/WC c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Seagate ST15230W/WD/WC - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Seagate ST15230W/WD/WC, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Seagate ST15230W/WD/WC va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Seagate ST15230W/WD/WC, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Seagate ST15230W/WD/WC.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Seagate ST15230W/WD/WC. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Seagate ST15230W/WD/WC ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
