Manuel d'utilisation / d'entretien du produit UD46A du fabricant Samsung
Aller à la page of 150
SyncMaster UD46A, UD55A LCD Display User Manual The color and the appearance may differ depending on the product, and the specificatio ns are subjec t to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Do not use a cleaning agent that contains alcohol or solvents, or that is surface active. Otherwise, the exterior may discolor or crack or the panel coating may come off. Do not spray water or cleaning agent directly onto the monitor. Otherwise, the liquid may sink into the monitor and cause a fire, electric shock, or failure.
Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock.
Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.
Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. To avoid eyestrain, do not sit too close to the product.
When replacing the battery, insert it with the right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.
Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury. • Since the front part of the product is heavy, install the product on a level and stable surface. Do not put any heavy objects on the product.
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package box. Check the contents of the package. Remove the styrofoam and vinyl cover.
Manuals Quick Setup Guide Warranty Card (Not available in some loca- tions) User Manual Cables Power Cord D-Sub Cable Others Remote Control Batteries (AAA X 2) (Not available in some loca- tions) Hold.
Sold separately RGB to BNC Cable RGB to Component Cable Network Box HDMI to HDMI Cable Stereo Cable AV Cable DP Cable Note Accessories that can be purchased with the product vary by country. Your LCD Display Function knob The function knob has a remote-control sensor, a light sensor and function keys.
Automatically detects the intensity of ambient light around a selected display and adjusts the screen brightness. Note It work when you use the MDC program. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions.
Attaching the knob to the side Attaching the function knob to the display • The function knob can be attached to any screw hole on the display. • Align the screw holes of the display and function knob. Next, fasten using the screw. Note Using a screw other than the one supplied can damage the display.
IR OUT Receives a signal from the remote control and outputs the signal through Loopout when a re- movable sensor board is connected. CONTROL IN Connects to the function (Power/Source) control buttons and receives the light sensor signal and remote control's IR signal.
DVI IN (PC Video Connection Terminal) Connect the [ DVI IN] port on the monitor to the DVI port on the PC using the DVI cable. RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/ DP/HDMI Audio Connection Terminal (Inpu.
Note • A normal external device (DVD player or camcorder, etc.) or a TV tuner box (US Only) can be connected to the [ HDMI IN 1] termi- nal. • To use a TV tuner box (US Only), make sure to connect it to the [ HDMI IN 1] terminal.
Switches the LCD Display On/Off. The power cord plugs into the LCD Display and the wall outlet. Kensington Lock slot An anti-theft lock allows you to use the product securely even in public places. The locking de- vice shape and locking method depend on the manufacturer.
SOURCE OFF Number Buttons + VOL - CONTENT (HOME) MagicInfo Lite TOOLS Up-Down Left-Right / Enter buttons RETURN The Color button / The PC/DVI/HDMI/DP se- lection button MagicInfo 3D ( ) / / / ( ) / D.MENU MUTE CH MENU BLANK INFO EXIT LOCK Power on the product.
CONTENT (HOME) Not available. MagicInfo Lite Not available. TOOLS Quickly select frequently used functions. - Enabled only when a TV tuner box(sold separately) is connected. Up-Down Left-Right / Enter buttons Up-Down Left-Right button : Move to the upper, lower, left or right menu, or adjust an option's setting.
Attaching the holders • Fix the holders into s on the back of the product using the screws. When displays are connected to form a video wall, the holders will make the gap between displays uniform on all four sides.
For a 3x3 video wall • To attach the decoration brackets to the sides of a video wall or Samsung UD installed, remove the stickers from the screw holes first.
• A Samsung Electronics service center can provide details. Tilt Angle and Rotation 1 2 1. The product can be tilted up to 15 degrees from a vertical wall. 2. To use the product in portrait mode, rotate it clockwise so that the LED indicator is at the bottom.
2. Embedded Mount guide <Side view> <Top view> A : min. 40 mm B : min. 70 mm C : min. 50 mm D : min. 50 mm E : Ambient temperature Measuring point < 35°C • When embedding the product in a wall, be sure there is some space behind the product for venti- lation, as shown above, and maintain the ambient temperature at 35°C or lower.
Dimensions (unit:mm) UD55A Introduction.
Notice • All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. • For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Wall Mount Kit Specifications (VESA) Note Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If you install the product on a slanted wall, it may fall and result in severe personal injury.
pin TxD(No.2) RxD(No.3) GND(No.5) Bits rate 9600 bps Data Bits 8 bit Parity None Stop Bits 1 bit Flow control None Maximum length 15 m (only shielded type) • Pin assignment Pin Signal 1 Data Carrier.
Control codes • Get control Header command ID DATA Length CheckSum 0xAA command type 0 • Set control Header command ID DATA Length DATA CheckSum 0xAA command type 1 Value • commanding words No.
Header command ID DATA Length DATA 1 CheckSum 0xAA 0x11 1 Power Header command ID DATA Length DATA 1 12 0xAA 0x11 1 1 If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID part to "0xFE" and send commands.
• Volume Control • Function Personal Computer changes volume of TV / Monitor. • Get Volume Status Header command ID DATA Length CheckSum 0xAA 0x12 0 • Set Volume Header command ID DATA Length DATA CheckSum 0xAA 0x12 1 Volume Volume : Volume value code to be set on TV / Monitor.
Input Source : Input Source code to be set on TV / Monitor. 0x14 PC 0x1E BNC 0x18 DVI 0x0C AV 0x04 S-Video 0x08 Component 0x20 MagicInfo 0x1F DVI_VIDEO 0x30 RF(TV) 0x40 DTV 0x21 HDMI1 0x22 HDMI1_PC 0x.
Caution Only works with models include TV. • Get Screen Mode Status Header command ID DATA Length CheckSum 0xAA 0x18 0 • Set Picture Size Header command ID DATA Length DATA CheckSum 0xAA 0x18 1 Screen Mode Screen Mode : Screen Mode code to be set on TV / Monitor.
• Ack Header command ID DATA Length Ack/Nak r-CMD Val1 Check Sum 0xAA 0xFF 3 ‘A’ 0x19 Screen Size Screen Size : Screen Size of TV / Monitor. (Range : 0 ~ 255, Unit : Inch) • Nak Header command ID DATA Length Ack/Nak r-CMD Val1 Check Sum 0xAA 0xFF 3 ‘N’ 0x19 ERR ERR : Error code that shows what occurred error is.
Header command ID DATA Length Ack/Nak r-CMD Val1 Check Sum 0xAA 0xFF 3 ‘N’ 0x3C ERR ERR : Error code that shows what occurred error is. • Auto Adjustment Control (PC, BNC Only) • Function Personal Computer controls PC system screen automatically.
• Get Video Wall Mode Header command ID DATA Length CheckSum 0xAA 0x5C 0 • Set Video Wall Mode Header command ID DATA Length DATA CheckSum 0xAA 0x5C 1 Video Wall Mode Video Wall Mode : Video Wall Mode code to be set on TV / Monitor.
Header command ID DATA Length DATA CheckSum 0xAA 0x5D 1 Safety Lock Safety Lock : Lock code to be set on TV / Monitor. 1 : ON 0 : OFF • Ack Header command ID DATA Length Ack/Nak r-CMD Val1 Check Sum.
Connections Connecting a Computer Note Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. There are several ways to connect the computer to the monitor. Choose one from the following options.
• Connect the DVI Cable to the [ DVI IN] port on the back of your LCD Display and the DVI port on the computer. Using the DP (Digital) connector on the video card. • Connect the [ DP IN] port on the LCD Display to the DP port on the PC using the DP cable.
Connecting to Other devices Note • Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. • AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.
Connecting AV Devices 1. Connect an audio cable to [ AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the product and the audio port on an external device such as a VCR or DVD player. 2. Connect a video cable to [ AV IN] on the product and the video output port on the external device.
3. Press SOURCE on the product or remote control and select " AV ". 4. Then, start the Camcorders with a tape inserted. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.
Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [ HDMI IN 2 (MAGICINFO)] or [ HDMI IN 1] and the DVI output port on the digital device.
Note • Press SOURCE on the product or remote control and select " Component ". • Then, start the DVD Player with a DVD disc inserted. • A RGB to component cable is optional. • For an explanation of Component video, consult your DVD manual.
Connecting to an Audio System 1. Connect a set of Stereo Cable between the AUX L, R jacks on the AUDIO SYS- TEM and [ AUDIO OUT] on LCD Display. Connecting a Network Box (sold separately) Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics.
Connecting to MAGICINFO OUT Connect the MAGICINFO terminal on the network box to the HDMI IN2(MAGICINFO) terminal on the product using the MAGICINFO OUT-HDMI cable. Note A MAGICINFO OUT-HDMI cable is provided with the network box. Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the network box and the [LAN] port on your PC.
Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Connections.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft ® Windows Vista™‚ Operating System 1.
Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage.
9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...
7. Click the "Browse" button then choose A:(D:Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft ® Windows ® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window.
4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button.
MDC Program Installation/Uninstallation Installation 1. Insert the installation CD into theCD-ROM drive. 2. Click the MDC Unified installation program. Note If a software installation window is not displayed on the main screen, install with the "MDC Unified"execution file in the MDC folder on the CD.
Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on t he PC and monitor. What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously usin g a PC.
Using MDC via Ethernet Enter the IP for the prima ry display device an d connect the device to the PC. One display device can connect to another using an RS-232C serial cable.
Connection Management Connection management includes the Connection list and Connection list modif ication options . Connection list – Connection list sho ws the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connec tion Type ), conn ection statu s, Set ID Range , and detected devices.
Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs conne cted in daisy-chain of a selected connection. There can be a ma ximum of 100 LFDs in a connection. The Se t ID is assigned se quentially in the da isy- chain runnin g from 1 to 99, and then finally to Set ID 0.
Command Retry This feature is used to sp ecify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be betwe en 1-10.
Getting Started with MDC 1 To start the pr ogram, click Start Programs Samsung MDC Unified . 2 Click Add to add a display device. z If the connection is established via RS232C, go to Serial and specify the COM Port .
z If the connection is established via Ethernet , enter the IP that wa s entered for the display device..
Main Screen Layout Menu Bar Change the status of a display device or the pr operties of the program. Device Category View a list of connected display devices or device groups. Schedule Category View a list of schedules for display devices. Set List Select the dis play device you want to adjust.
Menus You can power on or off a selected dev ice or change t he input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. Home Select an item and change the corresponding setting. Power z On : Power on a selected display.
This menu show s a list of display devices wh ich hav e following errors - fan e rror, temperature error, brightness sensor error, o r lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display de v ice.
Screen Adjustment The screen s ettings (contra st, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. z Color and Tint are not available if the input source is PC .
Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma valu e for the selected displa y. Auto Motion Plus This option is used to v iew dynamic ima ges. z Off : Disable the Auto Motion Plus function.
Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configur ation. The -/+ buttons c an be used to adjust Zoom . The screen can be reloca ted using the up/down/left/right butt ons.
Sound Adjustment You can change th e sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display.
System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole pic ture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group.
H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of ve rtical display devices. A maximum of 15 displays can be arranged in a row.
PIP Basic information required to adjust PIP will appear in the menu screen. z PIP will be disabled when Video Wall is ON . z Note that Picture Size is disabled when PIP is ON . PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source.
General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to aut omatically power on . Standby Control Set the standby mode to activate if an input source is not detected.
Security Safety Lock Lock the on-sc reen menus. To unlock the menus, set Safety Lock to Off . Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off . OSD Display Source OSD Select whether to display a message when the Source is changed.
Time Clock Set Change the current time on the selected displa y device accordin g to the time se t on a PC. If the time is not set on the display device, null values will be displayed. Timer z On Time : Set the time t o power on th e selected display dev ice.
Once EveryDay Mon~Fri Manual The checkboxes to select days of the week below Repeat are enabled only if Manual is selected. Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a sp ecifie d date.
Screen Burn Protection Pixel Shift Move the screen slightly at specified time inter vals to prevent screen burn-in. Screen Saver This function pre vents screen burn-in w hen the sc reen of th e selected displa y device is left idle for an extended period of time.
The Safety Screen function can be used to prevent scre en bu rn-in when a station ary image displays on the screen of a display de vice for an ext ended period of time. Lamp Control Lamp Control is used to adjust the bac klight to redu ce power consumpt ion.
Reset Reset Picture Reset the sc reen settings. Reset Sound Reset the sound settings. Reset System Reset the sys tem settings . Reset All Reset the screen, sound and system settings at the same time. Edit Column Select the items you want to display in the list of sets.
Other Functions Resizing a Window Place the mouse pointer on a corn er of the program window. An arro w will appear. Move the arrow to customize the size of the program window.
Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group>Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the sub level or Add on the same leve l .
The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 Select a group name, and click Edit . 2 In the Edit Group window displayed, click Delete . 3 Click Yes . The group will be deleted.
Schedule Management Creating Schedules Create and register a sc hedule on a grou p basis. 1 Click All Schedule List in the sch edule section on the le ft side of the program window. The Add button will be enabled in the middle. 2 Click the Add button.
3 Click Add belo w the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK . The schedule will be added and a list of schedules will appear in the set list window. z Device Gr oup : Select a group.
Troubleshooting Guide This program may malfunction sometimes due to a communication problem between the PC and display or electromagnetic waves emitted from nearby electronic devices. Issue Solution The display you wan t to control does not appear on th e system information chart.
How display properties are shown when multiple displays are used 1 When no display is selected: The default value is displayed. 2 When one display is selected: Settings for the selected disp lay are displayed. 3 When two displays are selected (e.g. in sequence of ID 1 and ID 3): The settings for ID 1 are displayed before the settings for ID 3.
Adjusting the LCD Display Input Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected.
However, the picture may display abnormally if the connected external input signal is different from the selected video signal. PIP Note The PIP function is not available when Video Wall is On .
• HDMI : PC • Display Port : PC Size Changes the Size of the PIP window. Note Picture > Size will be changed to 16:9 when PIP is On . Position Changes the Position of the PIP window.
Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note • The displayed devices differ depending on the external input mode.
Source AutoSwitch When the Source AutoSwitch is On , the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Sec- ondary source selection will become active, if no primary video source is available.
Specify Primary Source for the automatic input source. Secondary Source Specify Secondary Source for the automatic input source. Picture [ PC / DVI / DisplayPort / MagicInfo Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV.
Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). 3. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode.
Color Tone Note Not available when Dynamic Contrast is set to On . The color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool , Normal , Warm , or Custom , the Color Temp.
Note • Not available when Dynamic Contrast is set to On . • This function is only enabled if the Color Tone is set to Off . Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness.
Note • Not available when Dynamic Contrast is set to On . • Available in PC mode only. Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On . 1. R-Gain 2. G-Gain 3. B-Gain 4.
Size The Size can be switched. 1. 16:9 2. 4:3 HDMI Black Level When a DVD or set-top box is connected to your product via HDMI or DVI port, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc.
Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. 4. Color Adjusts the Color of the PIP window on the screen. Note PIP input only operates in DVI , AV , HDMI , or Component mode.
Uniformity Enhancer Make the screen brightness even throughout the whole screen. 1. Off 2. On Picture Reset Reset the screen settings. Picture [ AV / HDMI / Component / TV Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV.
The LCD Display has four automatic picture settings (" Dynamic ", " Standard ", " Movie " and " Cus- tom ") that are preset at the factory. Dynamic , Standard , Movie , or Custom can be activated. Note Not available when Dynamic Contrast is set to On .
Color Tone The color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On . 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2 , Cool1 , Normal , Warm1 , or Warm2 , the Color Temp.
Video mode ( HDMI [Video Timing], AV or Component ): 16:9 - Zoom1 - Zoom2 - 4:3 - Screen Fit - Custom 1. 16:9 - Sets the picture to 16:9 wide mode. 2. Zoom 1 - Magnifies the size of the picture on the screen. 3. Zoom 2 - Magnifies the size of the picture more than Zoom 1 .
etc., depending on the external device connected. In this case, adjust the screen quality of your product by configuring the HDMI Black Level . 1. Normal 2. Low Note For Timing which can be used for both the PC and the DTV in HDMI and DTV mode, HDMI Black Level will be activated.
Adjusts the Sharpness of the PIP window on the screen. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note Disabled when PIP is set to On . Lamp Control Adjusts the inverter lamp in order to reduce energy consumption.
Sound Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected.
Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass Emphasizes low frequency audio. Treble Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers.
1. Off 2. On Sound Select Enable the sound of either the primary or secondary display in PIP mode. Note Available when PIP is set to On . 1. Main 2. Sub Sound Reset Reset the sound settings.
Language You can choose one of 14 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Clock Set , Sleep Timer , Timer1 / Timer2 / Timer3 , and Holiday Management can be set.
5. 120 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Holiday : Select Apply to disable the timer on holidays and Don't Apply to enable the timer on holidays. • Only enabled when the clock is set using the Clock Set menu.
• Delete Selected You can delete selected holidays. Note • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted. • Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD.
Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000". Note If you forgot your password, press the remote buttons INFO → EXIT → MUTE to reset the password to "0000.
Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen.
Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6. Vertical Sets how many parts the screen should be divided vertically. Fifteen adjustment levels: 1~15.
Note When more than four displays are connected, we recommend a resolution of XGA (1024*768) or greater to prevent any picture degradation. Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time.
Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively.
Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution. • Mode - Bar , Eraser , Pixel : 10~50 sec Bar This function prevents after-images on the screen by moving long black and white vertical lines.
Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background. • Off • Light • Dark Resolution Select When .
5. 1366 X 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz. Power On Adjustment Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage.
Fan Control ( UD46A model Only) Selects auto or manual for the fan speed settings. • Auto • Manual Fan Speed Setting( UD46A model Only) Sets the fan speed within a range of 0 and 100. Note Enabled when Fan Control is set to Manual . Temperature Control Detects the product's internal temperature and specifies the desired temperature.
Current Temperature Shows the current temperature of the product. Auto Power Enables or disables Auto Power for the product. • Off • On Note When Auto Power is On , the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product.
User Auto Color 1. Auto Color Automatically adjusts the colors. 2. Reset Resets the color settings. Note Enabled only in PC mode. Standby Control Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read < No Signal > if no input signal is detected.
Lamp Schedule Adjusts the luminance to a user-specified value at a specified time. OSD Display Displays or hides a menu item on the screen. Source OSD • Off • On Not Optimum Mode OSD • Off • O.
• Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. 1. Connect the product to a computer via a digital signal such as DVI or HDMI . Click the BMP image file converted from an SW code. The image below will appear on the screen of the product.
Note • This only operates with a digital signal, such as in DVI , HDMI1 , or HDMI2 mode. (The input resolution must be identical to the panel resolution.) • In HDMI1 and HDMI2 modes, the timing values used for both the PC and TV are only supported if the Edit Name is set to PC or DVI PC .
ID Setup Assigns an individual ID to the SET ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MDC Connection Selects a port to receive the MDC inputs from.
- Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual . - Gateway : Manually enter the Gateway if IP Setting is set to Manual . MagicInfo Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV.
It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D, EWF is not applied.
When using multiple languages, you can choose and set a specific language among them. Note English is set as the default language. You do not need to select a language if you will be using English as the menu display language. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device.
Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display.
• Do not use benzene, thinner or other flammable substan- ces. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen sur- face.
(Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on.
Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory.
A: The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Control Panel → Appearance and Themes → Display → Settings.
Specifications General General Model Name SyncMaster UD46A SyncMaster UD55A LCD Panel Size 46 inch / 116cm 55 inch / 138 cm Display area Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7M Resolution Optimum resolution 1920 x 1080 @ 60 Hz 1920 x 1080 @ 60 Hz Maximum resolution Maximum Pixel Clock 148.
Environmental considerations Operating (With Network Box) Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Operating (Without Network Box) Temperature : 32°F ~ 104.
State Normal Op- eration Power saving mode Power off Power off ( Power Swich) (Typical) Typical : 175 Watts UD55A State Normal Op- eration Power saving mode Power off Power off ( Power Swich) Power In.
Display Mode Horizontal Frequency (kHz) Vertical Fre- quency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 768 47.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD.
Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recom- mended.
Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement. • Have the images and logo cycle periodically.
• Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display Information.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.
Europe http://www.samsung.com/be_fr (French) BOSNIA 05 133 1999 - BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com DENMARK 70 70 19 70 http://www.
Europe EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com CIS RUSSIA 8-800-555-55-55 http://www.samsung.
Asia Pacific 1-800-8-SAMSUNG(726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com THAILAND 1800-29-3232 02-689-3232 http://www.samsung.com TAIWAN 0800-329-999 0266-026-066 http://www.samsung.com VIETNAM 1 800 588 889 http://www.
• If a defect is caused by external environmental factors. (Internet, Antenna, Wired Signal, etc.) • If a product is reinstalled or devices are connected additionally after installing the purchased prod- uct for the first time. • If a product is reinstalled to move to a different spot or to move to a different house.
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The in- verse number of the Horizontal Cycle is called Horizontal Fre- quency.
Authority Information in this document is subject to change without notice. © 2012 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Samsung UD46A c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Samsung UD46A - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Samsung UD46A, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Samsung UD46A va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Samsung UD46A, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Samsung UD46A.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Samsung UD46A. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Samsung UD46A ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
