Manuel d'utilisation / d'entretien du produit 400UXN-2 du fabricant Samsung
Aller à la page of 122
SyncMaster 400UX-2, 400UXN-2, 460UX-2, 460UXN-2 LCD Display User Manual.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet.
Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the in- ternal temperature.
When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it softly with a dry cloth.
If thunder or lightning is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
The batteries (and rechargeable batteries) are not ordinary re- fuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
Do not put any heavy objects on the product. • This may result in personal injury and/or damage to the prod- uct. Safety Instructions.
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above.
Manuals Quick Setup Guide Warranty Card (Not available in all loca- tions) User's Guide MagicInfo Software CD, MagicInfo Manual CD (Applicable to the UXN-2 model only) Cables Power Cord Others Re.
Sold separately Wall Mount KIT RGB to BNC Cable BNC to BNC Cable (Applicable to the UX-2 model only) RGB to Component Cable Semi Stand KIT Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
SOURCE button [SOURCE] Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [ PC ] → [ DVI ] → [ AV ] → [ Component ] → [ HDMI ] → [ MagicInfo ] Note • The BNC mode will not be activated on the UXN-2 model.
Note Applicable to the UX-2 model only. Applicable to the UXN-2 model only. POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet.
DVI IN (PC Video Connection Terminal) Use a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DVI/RGB/HDMI AUDIO IN (PC/DVI/ HDMI(PC) Audio Connection Terminal (In- put)) AV/COMPONENT AUDIO IN [L- AUDIO- R] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ L- AUDIO - R ] port of the LCD Display.
your digital output device using a HDMI ca- ble. Up to HDMI cable 1.0 can be supported. BNC OUT [R, G, B, H, V] (BNC Terminal (Output)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. The number of LCD Displays that can be connected to the loopout depends on the ca- bles, signal source, etc.
Keyboard / Mouse, Mass Storage Device Compatible. Note Applicable to the UXN-2 model only. Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately.
POWER OFF Number Buttons DEL / GUIDE button + VOL - SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo 1. POWER Turns the product On. 2. OFF Turns the product Off. 3.
9. Up-Down Left-Right but- tons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 10. INFO Current picture information is displayed on the upper left corner of the screen. 11. COLOR BUTTONS Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu.
20. EXIT Exits from the menu screen. 21. MagicInfo MagicInfo Quick Launch Button. Introduction.
Connections Connecting a Computer Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display.
Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI port on the back of your LCD Display and the DVI port on the computer. Using the HDMI (digital) output on the graphics card. • Connect the HDMI IN port on the monitor to the HDMI port on the PC using the HDMI cable.
Using the BNC (Analog) connector on the video card. (Applicable to the UX-2 model only) • Connect the BNC/COMPONENT IN port on the monitor to the BNC port on the PC using the BNC to BNC cable. Connect the audio cable for your LCD Display to the audio port on the back of the LCD Display.
1. Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L] LCD Display. 2. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. 3. Select AV using the SOURCE . Connecting the BNC to BNC cable 1.
2. Connect a Component cable between the BNC/COMPONENT IN [R/Y, G/P B , B/P R ] port on the LCD Display and the P R , Y, P B jacks on the DVD player. Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control.
Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display .
Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI Cable 1. Connect between the DVI OUT port on the LCD Display and the input port on another monitor using a DVI cable. 2. Connect between the AUDIO OUT port on the LCD Display and the audio input port on another monitor using a stereo cable.
1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cabl.
1. Connect the RGB/COMPONENT IN ports on the monitor to the P R , Y, P B ports on the set-top box using the Component/ D-sub cable. 2. Connect a set of audio cables between the AV COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Connect the LAN cable. Note Applicable to the UXN-2 model only. Connecting a USB device Note • You can connect USB devices such as a mouse or keyboard.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD- ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the oper- ating system you have.
Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft ® Windows Vista™‚ Operating System 1.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage.
9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...
7. Click the "Browse" button then choose A:(D:Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft ® Windows ® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window.
If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click the "Finish" button and the "Close" button. Microsoft ® Windows ® Millennium Operating System 1. Click "Start", "Setting", "Control Panel".
5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.
Uninstall The MDC program can be removed only by using the "Add or Remove Programs" option of the Windows ® Control Panel. Perform the following steps remove MDC. Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a pro- gram".
Introduction A Multiple Display Control (MDC) is an application all owing various displa ys to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communi cation, is used for the comm unication between a PC and a display.
Main Icons Select Button Remocon Info G rid Safety Lock Display Selection Port Selection Control T o ols 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote cont rol signal receivi ng functi on of the display unit.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 throug h COM4 c an be selected in the Port Selection Menu. 3. If the exact port name that is co nnected to the LCD Display using a serial c able is not selected, communication will be unavailable.
Info Grid shows some basic information necessary to Power Control . 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All bu tto n or Check Box to choos e a dis play to control.
Power Control al lo ws controllin g so me of the fun ctio ns of the selected di splay. 1) Power On/Off - Turns the power o f the select ed dis play On/Off. 2) Volume - Controls the volum e level of the sele cted display. It receives the volume value of the selected displa y from the sets and displays it in the slider.
• PC Mode.
Info Grid shows some basic information necessary to Input Sourc e Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI.
The Input Source Control feature is available on ly fo r the displays whose powe r status is ON. Image Size PC, BNC, DVI 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control .
Image Size TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV 1. Click Image Size of the main icons an d the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control . 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Vide o, Component, DVI (HD CP), HDMI, DTV.
1. Click Time of the main icons and the Time Control scr een appears. Info Grid shows some basic information necessary to Time Co ntrol. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time.
PIP Size 1. Click PIP of the main icons and the P IP control screen appears. Click Select All or use Check Box to select a display to control. Info Grid shows some basic information necessary to PIP Size Contro l. 1) PIP Size - Shows the current PIP Si ze of the display in use.
PIP PIP Source 1. Click PIP of the main icons and the P IP control screen appears. Info Grid shows some basic information necessary to PIP Sourc e Control. 1) PIP Source - PIP Source can be controlled wi th turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC.
Settings Picture 1. Click Settings of the main icons an d the Settings Control screen appears. Info Grid shows some basi c in formati on n ec essary to Settings Cont ro l . When each func ti on is select ed, the set value of the selected function is displayed in the slide.
-A d j usts the Color Tone for the selected display. 8) Color Temp -A d j usts the Color Temp for the selected display. 9) Brightness Sensor -A d j usts the Bri g htness Sensor for the selected display. 10) Dynamic Contrast -A d j usts the Dynamic Contr ast for the selected display.
2) Contrast -A d j usts Contrast of the selected display. 3) Brightness -A d j usts Bri g htness for the selected display. 4) Red -A d j usts red Color o f the selected dis play. - Available on ly f or NT. 5) Green -A d j usts g reen Color of the s elected d isplay.
Info Grid shows some basic information necessary to Setting s Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each func tion fetches the value for the set and displays it on the slide bar.
Image Lock 1. Click Settings of the main icons an d the Settings Control screen appears. Info Grid shows some basi c in formati on n ec essary to Settings Cont ro l . 1) Image Lock - Available only fo r PC, BNC. 2) Coarse - Adjusts Coarse of the selected display.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenan ce Control function for al l input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time.
1) Scroll - This func tio n is used to remove the af ter i m a ges that occur when a s t il l sc reen is displa yed on the selected display for a long time.
1. Click on the "Mainten ance" icon in the Main Icon column to dis play the Maintenanc e sc r een . 1) Video Wall - A Video Wall is a set of video scree ns that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen.
You may not operate this function in MagicInfo. The Input source of TV works onl y on TV model. The Maintenance Control function is available only for the di splays where the power status is ON. Troubleshooting 1. The display you wish to control does no t appear on the Power Contro l Info Grid - Check the connection of RS232C.
2. Selected one display: Fetche s and displays the settings value for the selec ted display. 3. Selected one display (ID1) and add another display (ID3): The program, which was displ aying the settin gs value of ID 1, fetches and displays the value of ID3.
Adjusting the LCD Display Input Available Modes • PC / DVI / BNC • AV • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model.
When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. ( Off / On ) MENU → ENTER → → → ENTER → Note • More than one PIP cannot be overlapped on screen as BNC and the Component use the same terminal.
• HDMI : PC / BNC Swap MENU → ENTER → → → ENTER → → → → ENTER → Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window.
→ , → ENTER Adjusts the Transparency of PIP windows. • High • Medium • Low • Opaque Note • PIP turns off when the LCD Display is switched to an external source.
Picture [ PC / DVI / BNC / MagicInfo Mode] Available Modes • PC / DVI / BNC • AV • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model.
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
→ , → ENTER The color tones can be changed. (Not available when Dynamic Contrast is set to On .) 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool , Normal , Warm , or Custom , the Color Temp.
→ , → ENTER Blue MENU → → ENTER → → → → → ENTER → → → → ENTER → → , → ENTER Color Temp. MENU → → ENTER → → → → → → ENTER → → , → ENTER Color Temp. is a measure of the 'warmth' of the image colors.
→ , → ENTER Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Position MENU → → ENTER → → → → → → → ENTER → → → → ENTER → → , , , → ENTER Adjusts the screen location horizontally and vertically.
→ , → ENTER Selects either On or Off with the signal control. Signal Control MENU → → ENTER → → → → → → → → → ENTER → → ENTER → → 1. R-Gain MENU → → ENTER → → → → → → → → → ENTER → → ENTER → → → ENTER → → , → ENTER 2.
MENU → → ENTER → → → → → → → → → ENTER → → ENTER → → → → → → → → ENTER → → , → ENTER Size MENU → → ENTER → → → → → → → → → → ENTER → → , → ENTER The Size can be switched. 1.
PIP Picture MENU → → ENTER → → → → → → → → → → → ENTER → → , → ENTER Adjusts the PIP Screen Settings. Note • Available Modes: PIP ON 1. Contrast MENU → → ENTER → → → → → → → → → → → ENTER → → ENTER → → , → ENTER Adjusts the Contrast of the PIP window on the screen.
Note Enabled only when the PIP input is selected in AV , HDMI or Component mode. 5. Tint MENU → → ENTER → → → → → → → → → → → ENTER → → → → → → ENTER → → , → ENTER Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV , HDMI or Component mode.
Picture [ AV / HDMI / Component Mode] Available Modes • PC / DVI / BNC • AV • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model.
Contrast MENU → → ENTER → → → ENTER → → ENTER → → , → ENTER Adjusts the Contrast. Brightness MENU → → ENTER → → → ENTER → → → ENTER → → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → → → ENTER → → → → ENTER → → , → ENTER Adjusts the picture Sharpness.
→ , → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available when Dynamic Contrast is set to On .) 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2 , Cool1 , Normal , Warm1 , or Warm2 , the Color Temp.
→ , → ENTER The Size can be switched. 1. 16:9 : Sets the picture to 16:9 wide mode. 2. Zoom 1 : Magnifies the size of the picture on the screen. 3. Zoom 2 : Magnifies the size of the picture more than Zoom 1 . 4. 4:3 : Sets the picture to 4:3 normal mode.
→ , → ENTER When a DVD or set-top box is connected to your TV via HDMI or DVI, it may cause a deg- radation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Note • Available Modes: PIP ON 1. Contrast MENU → → ENTER → → → → → → → → → → ENTER → → ENTER → → , → ENTER Adjusts the Contrast of the PIP window on the screen.
→ , → ENTER Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV , HDMI or Component mode. Oper- ates only if the video signal is NTSC.
• MagicInfo Note • The BNC mode will not be activated on the UXN-2 model. • MagicInfo supports the UXN-2 model only. Mode MENU → → → ENTER → → ENTER → → , → ENTER The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings.
→ , → ENTER Emphasizes low frequency audio. Treble MENU → → → ENTER → → → ENTER → → → ENTER → → , → ENTER Emphasizes high frequency audio. Balance MENU → → → ENTER → → → ENTER → → → → ENTER → → , → ENTER Allows you to Adjusts the sound balance between the left and right speakers.
→ , → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround XT delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers.
→ , → ENTER When you use the product with it connecting to a Home theater, turn the Internal speakers off so you can listen to sound from the Home theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker.
Time Selects from one of 4 time settings, Clock Set , Sleep Timer , On Timer , and Off Timer . MENU → → → → ENTER → → → ENTER → Clock Set MENU → → → → ENTER → → → ENTER → → ENTER → → , → , → ENTER Current Time Setting.
→ , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU → → → → ENTER → → → ENTER → → → → → ENTER → → , / , → ENTER Turns the LCD Display off automatically at a preset time.
Safety Lock Change PIN MENU → → → → ENTER → → → → → ENTER → → ENTER → → [0 ∼ 9] → [0 ∼ 9] → [0 ∼ 9] → [0 ∼ 9] The password can be changed.
2. On Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting.
Provides a full screen without any margins. 2. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU → → → → ENTER → → → → → → → → ENTER → → → → ENTER → → , → ENTER Sets how many parts the screen should be divided horizontally.
The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Divider. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode.
Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical MENU → → → → ENTER → → → → → → → → → ENTER → → ENTER → → → → ENTER → → , → ENTER Sets how many pixels the screen moves vertically.
1. Off 2. On Mode MENU → → → → ENTER → → → → → → → → → ENTER → → → ENTER → → → ENTER → → , → ENTER You can change the Safety Screen Type.
• Mode - Bar , Eraser : 10~50 sec Scroll MENU → → → → ENTER → → → → → → → → → ENTER → → → → ENTER → This function helps to remove after-images on the screen by moving all the pixels on the LCD according to a pattern.
→ , → ENTER Select the brightness of the grey for the screen background. 1. Off 2. Light 3. Dark Resolution Select MENU → → → → ENTER → → → → → → → → → → ENTER → → .
Power On Adjustment MENU → → → → ENTER → → → → → → → → → → → ENTER → → , → ENTER Adjusts the Power On time for the screen. OSD Rotation MENU → → → → ENTER → → → → → → → → → → → → → → → ENTER → → , → ENTER OSD Rotate 1.
→ , → ENTER Note Available in PC mode only Note The Reset function is not available when Video Wall is On . Color Reset MENU → → → → ENTER → → → → → → → → → → → → .
MENU → → → → → ENTER → → ENTER → , → [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
• The preset password for the LCD Display is "000000". • The server program's Power-On option works only if the LCD Display's power is com- pletely shut off. Please make sure not to use the Power-On option when the LCD Display is in the process of shutting down since this may cause system errors on the LCD Display.
2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 When using multiple languages, you can choose and set a specific language among them.
You can select which rotation type will be applied to your device. 5. Setup Information Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display.
• Do not use benzene, thinner or other flammable sub- stances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
A: Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off.
Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu.
A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q & A Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card.
Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer.
Specifications General General Model Name SyncMaster 400UX-2, 400UXN-2 SyncMaster 460UX-2, 460UXN-2 LCD Panel Size SyncMaster 400UX-2, 400UXN-2 40 " Diagonal (101 cm) SyncMaster 460UX-2, 460UXN-2 46 " Diagonal (116 cm) Display area SyncMaster 400UX-2, 400UXN-2 885.
Maximum Pixel Clock 148.5MHz (Analog,Digital) Power Supply This product supports 100-240 V. Since the standard voltage may differ from country to country, please check the label on the back of the product.
Dot Acceptable black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice.
Display Mode Horizontal Frequency (kHz) Vertical Fre- quency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT- LCD.
Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended.
• Avoid using a combination of characters and background color with large dif- ference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance.
• Time Period : 1 ~ 5 seconds ( Recommend : 5 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
- Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 seconds ( Recommend : 50 ) N.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.
Europe BELGIUM 02 201 2418 http://www.samsung.com/be (Dutch) http://www.samsung.com/ be_fr (French) CZECH REPUBLIC 800 - SAMSUNG (800-726786) http://www.samsung.com/cz DENMARK 8 - SAMSUNG (7267864) http://www.samsung.com/dk EIRE 0818 717 100 http://www.
Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858 400-810-5858 010-6475 1880 http://www.samsung.com/cn HONG KONG:3698 - 4698 http://www.samsung.com/hk INDIA 3030 8282 1-800-3000-8282 1800 110011 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.
Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method.
Correct disposal of batteries in this product - Europe only are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please sep- arate batteries from other types of waste and recycle them through your local, free battery return system.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Samsung 400UXN-2 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Samsung 400UXN-2 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Samsung 400UXN-2, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Samsung 400UXN-2 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Samsung 400UXN-2, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Samsung 400UXN-2.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Samsung 400UXN-2. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Samsung 400UXN-2 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
