Manuel d'utilisation / d'entretien du produit 211014 du fabricant Russell Corporation
Aller à la page of 30
1 03/05 P/N 211014 Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 7921 Internet Address: http://www.
2 P/N 211014 03/05 201246 1 1/04 In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system.
3 03/05 P/N 211014 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s basketball systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to instructions.
4 P/N 211014 03/05 Get to know the basic parts of your basketball system... FRONT VIEW TOP POLE BACK VIEW MIDDLE POLE FRONT COVER RIM BOTTOM POLE STRUTS ELEV A TOR ASSEMBL Y BACKBOARD BASE WHEEL CARRI.
5 03/05 P/N 211014 P AR TS LIST (SEE P ARTS IDENTIFIER) Item Qty Part No Description P-1 1 908164 Top Pole Section P-2 1 908107 Middle Pole Section (with Label) P-3 1 908165 Bottom Pole Section P-4 2 .
6 P/N 211014 03/05 P AR TS IDENTIFIER P-31 (1) P-30 (1) P-18 (1) P-26 (1) P-28 (2) P-32 (1) P-22 (1) P-23 (1) P-29 (1) P-24 (1) P-25 (1) P-21 (2) P-19 (2) P-20 (2) P-14 (1) P-15 (1) P-16 (2) P-17 (2) 204532 11/04 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position.
7 03/05 P/N 211014 HARDW ARE LIST (SEE HARDW ARE IDENTIFIER) Item Qty Part No Description H-1 4 206938 Pushnut, Black H-2 1 203223 Bolt, Carriage, 5/16-18 x 1" Long H-3 1 202662 Bolt, Hex, 5/16-18 x 4.5" Long H-4 7 203218 Washer 5/16 H-5 1 200188 Rod 3/8 x 5.
8 P/N 211014 03/05 Item H-6 (1) Item H-8 (1) Item H-12 (1) Item H-18 (8) Item H-19 (1) Item H-31 (1) Item H-25 (2) Item H-21 (2) Item #H-29 (4) Item H-3 (1) Item #H-10 (1) Item H-16 (2) Item H-27 (4) .
9 03/05 P/N 211014 Item H-20 (4) Item H-23 (2) Item H-26 (6) Item H-4 (7) Item H-15 (8) HARDW ARE IDENTIFIER (NUTS, W ASHERS & MET AL SP ACERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS & CAPS) I.
10 P/N 211014 03/05 SECTION A: ASSEMBLE THE POLES Wood Scrap P-2 P-1 5" (13 cm) 5" (13 cm) P-1 P-3 P-2 Pole Identification Sticker Pole Identification Sticker 2.
11 03/05 P/N 211014 While maintaining alignment, bounce assembly and lower section (P-3) together as shown until they no longer move toward taped reference mark. P-1 P-2 P-3 3. WOOD SCRAP (NOT SUPPLIED) TROUGH Align dimple of middle pole section (P-2) into trough of bottom pole section (P-3) as shown.
12 P/N 211014 03/05 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section. 1. Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-28) to axle using pushnuts (H-1). Carefully tap pushnut s (H-1) onto axle with hammer or mallet.
13 03/05 P/N 211014 3. Install rod (H-5) through holes in bottom pole section (P-3) and eyebolt (H-6). 2. Install wheel assembly to base (P-8) using bolt (H-2), and nut (H-1 1) as shown.
14 P/N 211014 03/05 H-26 H-5 H-6 P-8 H-4 P-26 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. W ARNING! Insert pole assembly into tank (P-8) and through center hole on wheel assembly as shown.
15 03/05 P/N 211014 5. P-13 P-13 Secure tank strut s (P-13) to pole using bolt (H-3), washers (H-4) and nut (H-23) as shown. Place bolt cover (H-7) over exposed end of bolt as shown. Rotate non-secured ends of t ank struts (P-13) outward to mounting holes in tank as shown.
16 P/N 211014 03/05 6. 7. Secure ends of tank strut s (P-13) to tank using bolt (H-21), washers (H-4) and nut (H-1 1) as shown. Repeat for opposite side. Install upper pivot bracket (P-14) to front of base using bolt (H-8), washer (H-9) and nut (H-26) as shown.
17 03/05 P/N 211014 H-1 P-6 P-5 P-4 P-6 H-1 10. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORT ANT! Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-6) to axle using pushnuts (H-1). Carefully tap pushnut s onto axle with hammer or mallet.
18 P/N 211014 03/05 Position base as shown. Secure wheel bracket assembly with disc (P-23), washer (H-9) and nut (H-26) as shown. H-10 P-23 H-9 H-26 Carefully reposition entire assembly as shown: 11 . TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
19 03/05 P/N 211014 SECTION C: ASSEMBLE THE ELEV A TOR SYSTEM & BACKBOARD This is what your system will look like when you’ve finished this section.
20 P/N 211014 03/05 P-1 P-18 P-20 H-15 H-15 P-19 H-17 P-20 P-19 P-17 H-18 H-19 H-18 1. While the system is securely resting on the sawhorse. Install triangle plates (P-17) and elevator tubes (P-19 and P-20) to top pole section (P-1) as shown. Inst all pole cap (P-18) at this time.
21 03/05 P/N 211014 2. 3. Remove packaging materials from handle assemblies (P-10 and P-1 1). Remove screws on both sides of tube. P-1 1 P-10 P-1 1 Slide upper tube (P1 1) onto handle assembly (P-10). Reinsert screws removed in previous step as shown.
22 P/N 211014 03/05 Insert spacer (H-22) through springs (P-12) then assemble lower elevator tubes (P-19), and springs (P-12), to brackets (P-21) using bolts (H-18), plastic sp acers (H-20), metal spacer (H-22) and nut s (H-15) as shown. 5. P-21 H-20 H-15 H-20 H-22 P-12 H-22 P-12 6.
23 03/05 P/N 211014 7. P-31 H-33 H-32 P-30 H-31 Inst all Slam Jam Rim to Backboard P-29 P-32 H-31 H-32 H-33 A B C D E A. Fit rim (P-29) securely into bracket (P-30) as shown. Allow T -bolt (H-31) to slip through center hole in rim (P-29). B. Install reinforcement bracket (P-31) onto T -bolt (H-31) as shown.
24 P/N 211014 03/05 P-20 P-20 H-18 H-20 P-21 H-15 H-20 Assemble upper elevator tubes (P-20) to brackets using bolt (H-18), plastic sp acers (H-20), and nut (H-15) as shown. 8. P-19 P-19 TIGHTEN BOLT (H-18) IN LOCK NUT (H-15) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE.
25 03/05 P/N 211014 H-18 H-15 P-1 P-20 P-19 P-17 P-1 1 9. Install handle assembly (P-10 and P-1 1) to lower elevator tubes (P-19) using bolt (H-18), spacers (H-14), and nut (H-15) as shown. P-20 P-19 H-14 H-14 Secure the handle assembly (P-10 & P-1 1) to pole bracket (P-9) using bolt (H-30) and nut (H-23) as shown.
26 P/N 211014 03/05 P-20 P-12 H-15 P-20 11 . Insert bolt (H-18) through left side upper elevator tube (P-20), then stretch spring (P-12) onto bolt (H-18). Continue inserting bolt (H-18) through right side upper elevator tube (P-20) and secure with nut (H-15).
27 03/05 P/N 211014 12. Install net clip s (H-28). CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
28 P/N 211014 03/05 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snap s into position. Net must be centered through clip. NET NET CLIP SIDE VIEW NET NET CLIP 13.
29 03/05 P/N 211014 SECTION D: INST ALL FRONT COVER & HANDLE 1. Attach front cover (P-22) to hinge tubes (P-16) using carriage bolt s (H-27) and flange nuts (H-1 1) as shown. P-22 H-27 H-1 1 P-16 Upright system and fill base (P-8) with water (approximately 40 gallons) and snap fill cap (P-24) in place.
30 P/N 211014 03/05 1. Roll assembly to desired playing area. Secure assembly to ground using strap (P-26) and tie down stake (P-25). P-26 P-25 P-8 SECTION E: SECURING THE SYSTEM & APPL YING LABEL 2. Apply Height Adjustment and Moving Label (P-27) to front of pole, where it is clearly visible.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Russell Corporation 211014 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Russell Corporation 211014 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Russell Corporation 211014, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Russell Corporation 211014 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Russell Corporation 211014, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Russell Corporation 211014.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Russell Corporation 211014. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Russell Corporation 211014 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
