Manuel d'utilisation / d'entretien du produit Okidata C6100 du fabricant Radio Shack
Aller à la page of 24
Okidata C6100 Setup & User Guide.
1 Table of Contents - STEP 1- UNPACK/PREPARE PRINTER ……………… ……………………………………………………………………… 2 STEP 2 – PRINT DEMO PAGE .………..……………….…............... ............... ..
2 Step 1 – Unpack / Prepare Printer 1. Designate an area for your new printer to be installed. 2. Ask someone to assist in lifting the printer out of the box. 3. Lift the printer out of the box (straight up). 4. Remove all pieces of tape from the printer.
3 • Reinstall the black drum/toner unit. • Repeat these steps for all remaining drum/toner units. Important! If TONER SENSOR ERRO R appears when you turn on the printer, the lever for the toner cartridge color indicate d is not pushed all the way back.
4 • Load the paper (maximum 300 sheets 20-lb [75 g/m 2 ] paper). • Make sure the paper guides are snug against the paper and are locked in place. Note: Do not fill above paper full indicator (A).
5 Step 4 – Disconnect Current Printer (If one exists) 1. Press the power button to turn off the printer. 2. Disconnect the power cable from the power outlet and from the printer. Step 5 - Connect New Printer / Load Software For this portion, refer to the diagram pr ovided on page 20.
6 6. Next, if you agree, accept the License Agreement: The Installer screen will appear: 7. Click Install Driver ..
7 8. Select Network printer and click Next : 9. Use the mouse to select ‘Directly to the network using TCP/IP’ . Click Next ..
8 10. If you know the IP address for the printer, use the mouse to select IP address and ent er the number. If you do not know the IP address for your printer, click Next to browse for it.
9 11. Click the Back button to get to the IP address entry screen: 12. Enter the IP address and click Next . Note – use the tab key to enter IP address.
10 Drivers will be installed and you will see the following: 14. Use the mouse to click Finish , and exit out of any open Okidata screen s. 15. To make sure the printer driver was installed correctly, print a page from any program. Reinstall the driver if the installation failed.
11 Replace a Toner Cartridge 1. Press the cover release. Open the top cover. WARNING! If the printer has been powered on, the fuser is HOT. This area is clearly labeled. Do not touch it. 2. Note the positions of the four cartridges: Cyan (1) Magenta (2) Yellow (3) Black (4) .
12 4. Lift the right-hand end of the cartridge. Then, pull the cartridge to the right to release the left-hand end. Remove the toner cartridge. Discard it in accordance with your local regulations. 5. Unpack the new toner cartridge. Gently shake it from side to side to loosen and distribute the toner evenly inside the cartridge.
13 8 . • Lower the right end of the cartridge into the image drum unit. • Press it firmly down in place. • Then, push the colored lock lever back to open the toner slot and lock it in place. Important! The lever should move easily. If it does not, STOP! Push down on the toner cartridge to be sure that it is properly seated in the image drum.
14 Replace an Image Drum Important! You must replace the toner cartridge wh en you replace the image drum. The life expectancy of the cartridge will be reduced as the toner charges the new drum. 1. Press the cover release and open the top cover. WARNING! If the printer has been powered on, the fuser is HOT.
15 CAUTION! The green surface at the base of each image drum is very delicate and light sensitive. • Do not touch the green surface. • Never expose the drum to direct sunlight or to very bright room lighting. • Do not expose it to normal room light for more than 5 minutes.
16 5. Grasp the white tape tab and peel the tape off the drum. 6 . Remove the paper sheet. Then, remove the clear plastic film. 7. If present, remove the silica gel pack.
17 9. Remove the orange drum seal. 10 . Install the new toner cartridge in the image drum..
18 11. Use the provided LED lens cleaner. Gently wipe the LED. 12. Close and latch the top cover. Replace the Fuser WARNING! If the printer has been powered on, the fuser is HOT. This area is clearly labeled. Do not touch it. Handle the fuser with extreme care.
19 2. Pull the two blue fuser lock levers (1) towards the front of the printer. 3. • Hold the fuser by its handle . • Lift the fuser out of the printer. • If the fuser is still warm, place it on a flat surface which will not be damaged by heat. • After letting the fuser cool down, discard it.
20 6. Hold the new fuser by the handle. The fuser pressure release lever (1) should be on the right. Lower the fuser into the printer. 7. Push the two blue retaining levers (1) toward the rear of the printer to lock the fuser in place. 8. Close and latch the top cover.
21 Reset Factory Defau lt Settings To reset the printer menu to its original default settings: 1. Press + to enter the Menu Mode. 2. Press + until you see MAINTENANCE MENU . 3 . Press ENTER until you see MENU RESET (Execute) 4 . Press ENTER . 5 . The printer will reset and return to the on-line state.
22 Diagram – Front View 1. Output Stacker, face down Standard printed copy delivery point. Holds up to 250 sheets of 20-lb. (75 g/m²) paper. 2. Operator Panel - Menu driven operator controls and LCD display panel 3. Paper Tray Standard paper tray. Holds up to 300 sheets of 20-lb.
23 Diagram – Rear View 1. On/Off Switch 2. Socket for Power Cord – USE POWER CORD I N BOX 3. USB Interface –Connect HP Print Server to this port (optional – not covered by these instructions) 4.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Radio Shack Okidata C6100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Radio Shack Okidata C6100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Radio Shack Okidata C6100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Radio Shack Okidata C6100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Radio Shack Okidata C6100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Radio Shack Okidata C6100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Radio Shack Okidata C6100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Radio Shack Okidata C6100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
