Manuel d'utilisation / d'entretien du produit PP2000 du fabricant POSIFLEX Business Machines
Aller à la page of 30
Rev. A PP2000 Series 2 Station Printer User’s Guide.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
PP2000 (E) User’s Manual i Table of Contents PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 MAIN PARTS ON THE EXTERIOR . . . . . . 2 -- 1 OUTPUT AREAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1 CONTROL PANEL .
PP2000 (E) User’s Manual ii STORE STAMP (OPTION) . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 INTERNAL SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 CASH DRAWER CONNECTOR . . . . . . . . . . . . . . . . . 6 -- 5 SERIAL INPUT CONNECTOR (STANDARD 9 PIN RS232 INTERFACE) .
PP2000 (E) User’s Manual 1 - 1 I. PRODUCT BRIEFING This is a high speed 2 - station journal / receipt printer. l A standard 2 station Journal / Receipt printer: The printing paper width is 44.5 mm. The printer can print both journal and receipt at the same time or only journal or receipt alone.
PP2000 (E) User’s Manual 1 - 2 l Options include auto stamping ability of the store stamp on receipt and auto cutting of the receipt. l The ability of cutting paper in full or in part by software on receipt .
PP2000 (E) User’s Manual 2 - 1 II. MAIN PARTS ON THE EXTERIOR A. OUTPUT AREAS B. CONTROL PANEL Receipt exit slot Journal window Validation printing insert slot Power LED On line LED Power On/Off swi.
PP2000 (E) User’s Manual 2 - 2 C. INPUT / OUTPUT CONNECTOR Cash drawer connector Serial connector Power connector Parallel connector.
PP2000 (E) User’s Manual 3 - 1 III. INS TALL ATION A. CHECK CONTENTS When you unpack carefully the carton that delivers PP2000 series printer, you will find it contains several items as illustrated below.
PP2000 (E) User’s Manual 3 - 2 C. STORE STAMP INSTALLATION If your printer comes with stamp option, you can find a store stamp case in the rear of the receipt part of print anvil assembly. You may take it out gently by holding its handle with your fingers.
PP2000 (E) User’s Manual 3 - 3 of store stamp. When the printing ink of the stamp is not enough , you can drip printing ink into the two holes in the rear of the stamp case. D. R IBBON INSTALLATION / REPLACEMENT When replacing the ribbon, please take the handle at the center of the old ribbon case and lift it up.
PP2000 (E) User’s Manual 3 - 4 turn the knob of the ribbon in the marked direction to tighten the ribbon and to ensure proper operation of the ribbon and to avoid jamming. E. CASH DRAWER CONNECTION Using the Posiflex signal cable CCBLA-180 to control a Posiflex cash drawer ( CR3100 or CR3200).
PP2000 (E) User’s Manual 3 - 5 H. POWER ON Turn on the On/Off switch at the left to the control panel, there will be a short buzzing sound and it indicate s a normal power on. I. PAPER ROLLS INSTALLATION 1. Please refer to the picture above: Put the receipt roll into the left paper roll compartment and the journal roll into the right.
PP2000 (E) User’s Manual 3 - 6 4. To give an idea about the positioning matter of the receipt, the print center is 33.3 mm behind the auto-cut position, whilst the stamp center is 40.
PP2000 (E) User’s Manual 4 - 1 IV. MAINTENANCE NOTICES l The printer should be put at a well ventilated site and avoid direct sunshine, also avoid high temperature, high humidity, high magnetic field. The site should also be free from lots of metal chips and dust.
.
PP2000 (E) User’s Manual 5 - 1 V. SOFT WA RE COMMANDS The commands supported by the PP2000 Printer are listed below. For detail description of the below listed commands, please visit our web site http://www.posiflex.com.tw for detail descriptions of each command.
PP2000 (E) User’s Manual 5 - 2 Software commands continued. NAME HEX FUNCTION ESC o 1B 6F Stamp ESC p 1B 70 Generate pulse ESC t 1B 74 Select character code table ESC u 1B 75 Transmit peripheral dev.
PP2000 (E) User’s Manual 6 - 1 VI. SPECIFIC ATIONS A. VALIDATION PRINTING Paper width: 140 mm or above Paper height: 65 mm or above Paper thickness: 0.07 ~ 0.14 mm Validation print: One line Number of characters: 55 Print area and sensor position: As illustrated in drawing above B.
PP2000 (E) User’s Manual 6 - 2 C. LED INDICATIONS Power LED: Green: Printer power is working On line LED: Green: Printer is at on line state. The printer takes command from the host system at this state and takes no command from the buttons. Receipt LED: Red: Receipt pa per is out, or malfunction with receipt print.
PP2000 (E) User’s Manual 6 - 3 E. PRINTER GENERAL SPEC ITEM SPECIFICATION Functions Receipt, journal and validation printing Printing Method 9 pin dot matrix impact; synchronized or separate printing of receipt and/or journal Printing Speed About 3 lines/sec.
PP2000 (E) User’s Manual 6 - 4 F. STORE STAMP (OPTION) Cushion width: 34.0 mm Cushion height: 24.0 mm Cushion thickness: 1.0 mm Cushion material: PE foam Stamp total width: 34.0 mm Stamp total height: 24.0 mm ( engraving included ) Stamp total thickness: 5.
PP2000 (E) User’s Manual 6 - 5 H. CASH DRAWER CONNECTOR PIN DEFINITION 1 Frame ground 2 CR2 kick (by Esc p 0 n1 n2) 3 Drawer open sense 4 +24 V DC power 5 CR1 kick (by Esc p 1 n1 n2) 6 Signal ground I. SERI AL INPUT CONNECTOR ( standard 9 pin RS232 interface) J.
PP2000 (E) User’s Manual 6 - 6 M. ENVIRONMENT Temperature: 0 ° C to 50 ° C Humidity: RH 10% to RH 90% without condensation N. RELI ABILITY Printer mechanism (without print head) life: 8,000,000 lines Print head life: 150,000,000 characters (2 dots/wire/character average) O.
PP2000 (E) User’s Manual 7 - 1 VII. REGULAR MAINTENANCE PROCEDURE A. DAILY MAINTENANCE Perform a basic cleaning and maintenance daily at a suitable timing as following 1. Turn power off and open the top cover. Press down the receipt lever and the journal lever.
PP2000 (E) User’s Manual 7 - 2 B. PERIODIC M AINTENANCE A periodic maintenance and lubrication should take place by a qualified maintenance specialist in every 6 months.
PP2000 (E) User’s Manual 8 - 1 VIII. BASIC TROUBLE SHOOTING A. NO OPERATION AFTER POWER ON If the printer does not work, neither does the power on LED lit: 1. Check if the power cord is well connected. 2. Check if the power outlet the printer is connected to is supplied with power.
PP2000 (E) User’s Manual 8 - 2 D. PAPER JAMMED In case of serious paper jammed problem, please pull both the receipt lever and the journal lever forward and push the print anvil assembly backward (as indicated in the picture) to raise the print anvil assembly.
PP2000 (E) User’s Manual 8 - 3 Once the print anvil assembly is lifted, the paper jam can be dismissed. Please clean the paper residue in the area before putting back the print anvil assembly if the condition requires. When you are putting back the print anvil, please pay special attention to the position of the pick up reel for journal.
PP2000 (E) User’s Manual 8 - 4 However, the journal pick up reel does not automatically move forward when the print anvil assembly is put back. Please then put the journal pick up reel back to its original location, and roll the reel so that the journal remains properly tensioned.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté POSIFLEX Business Machines PP2000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du POSIFLEX Business Machines PP2000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation POSIFLEX Business Machines PP2000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le POSIFLEX Business Machines PP2000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le POSIFLEX Business Machines PP2000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du POSIFLEX Business Machines PP2000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le POSIFLEX Business Machines PP2000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei POSIFLEX Business Machines PP2000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
