Manuel d'utilisation / d'entretien du produit 3300S du fabricant Acer
Aller à la page of 114
Aspire 3300S Service Guide P ART NO.: -- ----------------------- PRINTED IN T AIW AN Service guide files and updates are availab le on the AIPG/CSD web; for more in forma tion, please refer to http://csd.
ii Revision History Please refer to the table below for the updates ma de on Aspire 3300S service guide. Date Chapte r Updates.
iii Copyright Copyright © 2002 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any.
iv Conventions The following conventi ons are used in this manual: Screen messages Denotes actual messages that appe ar on screen. NOTE Gives bits and pieces of additional information related to the current topic. W ARNING Alerts you to any damage that might result from doing or not doing specific actions.
v Preface Before using this information and the product it s upports, please read the fo llowing general info rmation. 1. This Service Guide provides you with all techni cal information relating to the BASIC CON FIGURA TION decided for Acer's "glo bal" product offering.
vi Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front Panel Aspire 3300S . . . . . . . . . . . . . . . . . .
Chapter 1 1 Overview The Aspire 3300S supports Intel ® Pentium 4 (Willamette 478/Northwood) F lip Chip-Pin Grid Array 2 proce ssor (FC-PGA2) based Micro A TX, IBM PC/A T compatible system with PCI/AGP bus.
2 Chapter 1 Features Performance T Intel Pentium® IV processor with Intel NetBurst™ micro-architecture and in tegrated 256KB/512KB on-die L2 cache memory in Flip Chip 2 (FC)-mP GA 478 socket form factor , with supportin g CPU clock up to 2.4GHz+. T System Front Side bus speed:400 MHz.
Chapter 1 3 Exp ansion T 3 PCI slots + 2 DIMM slot s + 1 AGP slot T Upgradeable memory and hard disk Human-centric design and er gonomics T Slim desktop form factor T Separate computer stand and rubbe.
4 Chapter 1 Front Panel Aspire 3300S The computer ’s front panel consists of the following: Label Icon Color Description 1 Floppy drive light-emitting d iode (LED) 2 3.5-inch floppy drive 3 Floppy drive eject button 4 CD-ROM/DVD-ROM/CD-RW Headphone/Ear- phone jack.
Chapter 1 5 NOTE: *The system has two microph one-in ports (front and rear). However , you ca nnot use both of them at the same time. T he default settin g for your system en ables the microphone-in port in fron t and disables the one at the back.
6 Chapter 1 Rear Panel Aspire 3300S Label Icon Color Description 1 Power supply 2 V olt age selector switch 3 Keyhole 4 Green PS/2 mouse port 5 Gray Network port 6 Burgundy Parallel/Printer port 7 Gol.
Chapter 1 7 NOTE: * The CRT monitor port is automatically disabled when an add-on VGA card is installed into the system. Connect the monitor to the VGA port instead. * * The system has two microphone-in ports (front and rear). However , yo u can not use both of them at the same time.
8 Chapter 1 System Block Diagram (Aspire 3300S) INTEL P4 CPU Willamette / Northwood (FC-PGA2_478) Host Bus SIS 650 North Bridge Primary PCI Bus FWH (BIOS) LPC SUPER I/O SIS 961 South Bridge DDRAM 2XDI.
Chapter 1 9.
10 Chapter 1 Main Board Layout (A spire 3300S) Compone nt Functi on A TX Power Supply/JPW1 A TX power connectors JKBMS1 Mouse/keyboard connector USB Connectors Connecting to USB devices COM A & CO.
Chapter 1 11 IDE 1~IDE 2 Hard disk connector JCD1/JAUX1/JMD1 CD/AUX/Modem-in connectors CPUF A/SYSF A Fan power connectors JFP1/JFP2 Front panel connectors JAUD Front panel audio connector JUSB1/JUSB2.
12 Chapter 1 Keyboard The keyboard has full-sized keys that include separate cursor keys, two Windows keys, and twelve function keys. No. Component Description 1 Programmable keys Help you directly access a URL (Web site) or launch any program, file, or application in your system.
Chapter 1 13 4 V olume control/Mute knob Controls the speaker volume. Turn it clockwise or c ounterclockwise to adjust the volume. Press it to toggle between mute and sou nd. 5 Scroll Lock [ When activated, the screen moves one line up or down when you pr ess the up arrow or down arrow r espectively .
14 Chapter 1 Hardware Specifications and Configurations NOTE: The BIOS can be overwrit ten/upgraded using the FLASH utility (A WDFLASH.EXE). Processor Item Specification T ype Intel® Pentium IV processors with mPGA478 package Slot Socket mPGA478 S peed Internal : 1.
Chapter 1 15 This section has two t abl e lists, system memory specification and the possible combinat ions of mem ory module. System Memory Item Specification Memory socket number 2 slots (4 banks) S.
16 Chapter 1 Audio Interface Item Specification Audio controller SiS961 Audio controller resident bus AC’97 link Audio function control Enabl e/disable by BIOS Setup Mono or stereo S tereo Resoluti on 16 bits Compatibility AC’97 2.
Chapter 1 17 Parallel Port Item Specification Parallel port controll er LPC Super I/O Parallel port controller resident bus LPC Number of parallel ports 1 Support ECP/EPP SPP/ECP / EPP 1.
18 Chapter 1 Note : UPPER LIMIT means the maximum size of installed memory . T he Main Me m ory Maximum size are 768M Bytes. Memory Address Map Address Size Functio n 000000 - 07FFFF 512KBytes Host Me.
Chapter 1 19 NOTE: N - Not to be used. I/O Address Map Hex Range Devices 000-00F 020-021 040-043 060-060 061-061 070-071 081-08F 0A0-0A1 0C0-0DF 0F0-0FF 170-177 1F0-1F7 278-27F 2F8-2FF 378-37F 3F0-3F5.
20 Chapter 1 NOTE: N - Not to be used. DRQ Assignment Map DRQx System Devices Add-On-Card Devices DRQ0 N (Notes) Reserved DRQ1 N Reserved DRQ2 Floppy Diskette N DRQ3 N Reserved DRQ4 Cascade N DRQ5 N R.
Chapter 1 21 (This is for 160W power supply) NOTE: 1. +3.3V and +5V total output power can’t exceed 80W . Mechanical Specifications Item Specification Weight One 3.
22 Chapter 1 Power Management Functions Device Standby Mode T Independent power management time r for hard disk drive devices (0-15 minutes, time step=1 minu te). T Hard disk drive goes into S tandby mode (for A T A standard interface). T Disable V -sync to control the VESA DPMS monitor .
Chapter 1 23.
Chapter 2 24 Most systems are already configured by the ma nufacturer or the dealer . There is no need to run Setup when st arting the computer unless you get a Run Setup message. The Setup program loads confi guration values into the battery-backed nonvolati le memory called CMOS RAM.
25 Chapter 2 Entering Setup Power on the computer abd the system will start POST (Power On Self T est)prosecc. When the message of “ Press DEL to enter SETUP ” appears on the screen, press the key of [Delete] to enter the setup menu.
Chapter 2 26 The command line at the bo ttom of the menu tells you how to move within a screen and from one screen to another . T T o select an option, move the highlight bar by pressing or then press . T T o change a parameter setting, press or until the desired setting i s found.
27 Chapter 2 Product Information The screen below appears if you select Produ ct Information from the main menu: The Product Information menu contains general data about the system, such as the product name, serial number , BIOS version, etc. These information is nec essary for troubleshooting (maybe required whe n asking for technical support).
Chapter 2 28 The following table describes th e parameters found in this menu: Parameter Description Product Name Displays the mo del name of your system. System S/N Displays your system’s serial number . Main Board ID Displays the ma in board’s identification number .
29 Chapter 2 S t andard CMOS Features Select S tandard CMOS Features from the main menu to configure some basic p arameters in your system. The following screen shows the St andard CMOS Features menu: The following table describes the parameters found in this menu.
Chapter 2 30 IDE Secondary Channel Master Allows you to configure the hard disk drive connected to the master port of IDE channel 2. T o enter the IDE Secondary Master setup, press [Enter].
31 Chapter 2 IDE Primary/Secondary Cha nnel Master/Slave Setup The following screen appea rs if you sele ct any of the IDE drive parameters: The following table describes the parameters found in this menu. Settin gs in boldface are the default and suggested settings.
Chapter 2 32 Advanced BIOS Features The following screen shows the Advanced BIOS Fea tures: The following table describes the parameters found in this menu. Settin gs in boldface are the default and suggested settings. Parameter Description Options Virus W arning Allows you to set the virus warning feature for IDE Hard Disk boot sector protection.
33 Chapter 2 Boot Up NumLock S tatus Sets the NumLock status when the system is powered on. Setting to On will turn on the NumLock key when the system is powered on. Setting to Off will allows users to use the arrow keys on the numeric keypad. On Off Gate A20 Option This item is to set the Gate A20 status.
Chapter 2 34 Advanced Chip set Features The advanced cipset features setup option is used to change th e values of the chipset registers. These registers control most of the sy stem options in the comp uter . NOTE: Change these settings only if yo u are fa miliar with the chipset.
35 Chapter 2 The following table describes each parameter under the sub-menu. Settings in boldfac e are the d efault and suggested value s. The other two parameters under the Advanced Chip set Features are prese nte d below . Settings in boldface are the deafult and sugge sted values.
Chapter 2 36 Integrated Peripherals The following table describes each Integrated Peripherals parameters. Settings in boldface are the default and suggested values. Parameter Description Options Internal PCI/IDE This setting enables or disables the internal primary and secondary PCI & IDE con trollers.
37 Chapter 2 USB Keyboard Support This item lets you enable or disable the USB keyboard driver within the onboard BIOS. The keyboard driver simulates legacy keyboard command and lets you use a USB keyboard during POST or after boot if you do not have a USB driver in the operating system.
Chapter 2 38 Power Management Setup The Power Management menu lets you configure your system to most ef fe ctively save energ y while operating in a manner consistent w ith your own style of computer use.
39 Chapter 2 Video Off Option This item is to control the mode in which the monitor will shut down. Always On: Always keep the monitor on. Suspend --> Off: During suspend mode, the monitorwill shut down. Susp, Stby --> During suspend or standby mode, the monitor will shut down.
Chapter 2 40 PnP/PCI Configuration The following table describes the parameters found in this menu. Settin gs in boldface are the default and suggested settings. NOTE: It is strongly recommen ded that only exp erienced users should make any ch ang es to the default settings.
41 Chapter 2 PC Health St atus The following table describes th e parameters found in this menu: Parameter Description Options Shutdown T emperature This option is for setting the shutdown temperature level for the processor . When the processor reaches the temperature you set, the ACPI-aware system will be shut down.
Chapter 2 42 Frequency Control The following table describes the parameters found in this menu. Settin gs in boldface are the default and suggested settings. Parameter Description Options Set CPU Ratio End users can overlock the processor by specifying the CPU ratio (clock multiplier) in t his field.
43 Chapter 2 Load Default Settings The default settings are the defaul t values set by t he mainb oard manufacturer specifi cally for optimal performance of the mainboard. When you se lect the item, a message as below appears: Pressing Y (Y es) loads the BI OS default values for the most stable system performance.
Chapter 2 44 Set Supervisor/User Password When you choose to set supervisor password, a message as below will appear on the screen: At the prompt, type your password. Y our password can be up to six characters in length. After typing the password, press “Enter”.
45 Chapter 2 If you select Set User Password, a message as below will appear: At the prompt, type your password. Y our password can be up to six characters in length. After typing the password, press “Enter”. At the next prompt, re-type your password and press “Enter” again to confirm the new password.
Chapter 2 46 Save & Exit Setup/ Exit Without Saving If you select Save and Exit Setup, you will exit the BIOS utility . The following dialogue b ox will appear . Select Y (Y es) to exit Setup. Select N (No) to return to the main men u. If you select Exit Without Saving, you will disca rd all the changes you made and exit Setup.
47 Chapter 2.
Chapter 3 48 This chapter contains step-by-s tep procedures on how to disass emble the V eriton 3300/3300D desktop computer for maintenan ce and troubleshooti ng.
49 Chapter 3 General Information Before Y ou Begin Before proceeding with the disassembly procedure, make su re that you do the following: 1. T urn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cab les from the system.
Chapter 3 50 Disassembly Pro cedure Flowchart The flowchart on the succeedi ng page gives you a graphical representation on the entire disassembly sequence and instructs you on the components th at need to be removed during servicing .
51 Chapter 3 Opening the H ousing This section tells you how to ope n the housing cover when you need to install additional components inside the system unit. CAUTION: Before you proceed, make sure that you have turned off the system and all peri pherals connected to it.
Chapter 3 52 Removing the Front Panel 1. See “Opening the Housing” on page 51 2. Remove the four screws as shown here. 3. Detach the front bezel from the front panel gently in the way as shown here. Removing the EMI Audio Cover 1. See “Opening the Housing” on page 51 2.
53 Chapter 3 Removing the Modem Card 1. See “Opening the Housing” on page 51 2. Remove the screw as shown below and then remove the mo dem card from the slot. Removing the AGP VGA Card 1. See “Opening the Housing” on page 51 2. Remove the screw as shown here and then remove the AGP VGA card from the slot.
Chapter 3 54 3. Disconnect the floppy disk dr ive and power cables from the floppy disk drive. 4. Disconnect the power cable, IDE cable, and audio cable from the DVD-ROM drive. 5. Disconnect the micro switch cable from the main boa rd. 6. Pull the FDD and DVD frame from the lower case.
55 Chapter 3 8. Remove the four screws as shown here then de tach the floppy disk drive from the frame. 9. Disconnect micro switch cable from the FDD and DVD frame. Removing the Intrusion Alarm Cable 1. See “Opening the Housing” on page 51 2. See “Removing the FDD and DVD Frame” on page 53” 3.
Chapter 3 56 Removing the USB and Audio Board 1. See “Opening the Housing” on page 51 2. See “Removing the EMI Audio Cover” on page 52 3. See “Removing the FDD and DVD Frame” on page 53 4. Disconnect the USB board ca ble and audio board cable from the USB and audio b oard.
57 Chapter 3 5. Slide the hard disk drive frame to the right and then gently move it inward to detach it from the lower case. 6. Remove the four screws as shown and then detach the hard disk drive from the frame. Removing the DIMM 1. See “Opening the Housing” on page 51 2.
Chapter 3 58 Removing the Power Supply 1. See “Opening the Housing” on page 51. 2. See “Removing the FDD and DVD Frame” on page 53” 3. Remove the two screws as shown here. 4. Disconnect the power cable from the main boa rd. 5. Gently remove the power supply from the system.
59 Chapter 3 Removing the Processor 1. See “Opening the Housing” on page 51 2. See “Removing the FDD and DVD Frame” on page 53” 3. Disconnect the fan sink cable from the main board, and then release the two levers on both sides of th e fan sink.
Chapter 3 60 Removing the Main board 1. See “Opening the Housing” on page 51 2. See “Removing the FDD and DVD Frame” on page 53 3. Remove the six screws as shown here then detach the main board from the lower case.
61 Chapter 3.
Chapter 4 62 This chapter provides troublesho oti ng informatio n for the Aspire 3300S: T Power-On Self-T est (POST) T Index of Error Message T Index of Error Symptoms T Undetermined Prob lems Chapter.
63 Chapter 4 Power-On Self-T est (POST) Each time you turn on the system, the Power-on Self T est (POST) is initia ted. Several items are tested during POST, but is for the most part transparent to the user .
Chapter 4 64 03h Initial Superio_Early _Init switch 04h Reserved 05h 1. Blank out screen 2. Clear CMOS error flag 06h Reserved 07h 1. Clear 8042 interface 2. Initialize 8042 self-test 08h 1. T est special keyboard controller for Winbond 977 series Super I/O chips.
65 Chapter 4 23h 1. Check validity of R TC value: e.g. a value of 5Ah is an invalid value f or RTC minute. 2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead. 3. Prepare BIOS resource map for PCI & PnP u se. If ESCD is valid, take into consideration of the ESCD’s legacy information.
Chapter 4 66 43h T est 8259 functionality 44h Reserved 45h Reserved 46h Reserved 47h Initialize EISA slot 48h Reserved 49h 1. Calculate tot al memory by testing the last double word of e ach 64K page. 2. Program writes allocation for AMD K5 CPU. 4Ah Reserved 4Bh Reserved 4Ch Reserved 4Dh Reserved 4Eh 1.
67 Chapter 4 67h Prep are memory size information for function call: INT 15h ax=E820h 68h Reserved 69h T urn on L2 cache 6Ah Reserved 6Bh Pro gram chipset registers according to it ems described in Setup& Auto-configuration tab le. 6Ch Reserved 6Dh 1.
Chapter 4 68 85h 1. USB final Initialization 2. NET PC: Build SYSID structure 3. Switch screen back to text mode. 4. Set up ACPI table at top of memory .
69 Chapter 4 POST Error Messages List If you cannot run the diagnostics program tests bu t did receive a POST error message, use “POST Error Messages List” to diagnose system prob lems. If you did not receive any error message, look for a description of your error symptoms in “E rror Symptoms List” on page 71 .
Chapter 4 70 Memory V erify Error Use this location al ong with your system’s memory map to locate the bad chip. Offending Address Not Found This message is used in conjunction with the I/O CHANNEL CHECK and RAM P A RITY ERROR messages when the segment that has caused problem cannot be isolated.
71 Chapter 4 Error Symptoms List NOTE: T o diagnose a problem, first find the e rror symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If n o check procedure i s indicated, the first Action/ FRU listed in right co lumn is the most likely cause.
Chapter 4 72 Diskette drive LED comes on for more than 2 minutes when reading d ata. 1. Diskette 2. Diskette drive connection/cable 3. Diskette drive 4. Main board Diskette drive LED fails to light, and the drive is unable to access for more than 2 minutes.
73 Chapter 4 Audio Audio software program invokes but no so und comes from speakers. 1. S peaker power/connection/cable. Modem Modem ring cannot wake up system from suspend mode. 1. For the External Modem, make sur e Power on By Ring in BIOS Setup or Power Management is set to Enabled.
Chapter 4 74 Parallel/Serial Ports Execute “Load BIOS Default Settings” in BIOS Setup to c onfirm p orts presence before di agnosing any parallel/serial ports problems. Serial or parallel port loop-back test failed. 1. Make sure that the LPT# or COM# you test is the same as the setting in BIOS Setup.
75 Chapter 4 Undetermined Problems If an error message is present, go to “POST Error Mess ages List” on page 69. If you did not receive any messages, see if the symptom i s listed in “Error Symp toms List” on page 71. If you still cannot so lve the problem, continue with this check: 1.
Chapter 5 76 The mainboard provides connectors to connect to FDD, IDE HDD, case, modem, LAN, USB Ports, IR module and CPU/System F AN. Floppy Disk Drive Connector: FDD1 The mainboard provides a standard floppy disk drive connector that supports 360K, 720K, 1.
77 Chapter 5 Hard Disk Connectors: IDE1 & IDE2 The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/66/100 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA33/66/100 function. Y ou can connect up to four hard disk drives, CD-ROM, 120MB Floppy (reserved for future BIOS) and other devices.
Chapter 5 78 CD-In Connector: JCD1 The connector is for CD-ROM audio connector. Aux Line-In Connector: JAUX1 The connector is for DVD add-on card with Line-in connector. Modem-In Connector: JMD1 The connector is for modem with internal audio connector.
79 Chapter 5 Fan Power Connectors: CPUF A/SYSF A The CPUF A (processor fan) & SYSF A (system fan) support system cool- ing fan with +12V. It supports three-pin head connector.
Chapter 5 80 Front Panel Connectors: JFP1 & JFP2 The mainboard provides front panel connectors for electrical connection to the front panel switches and LEDs. Users can choose either the JFP1 or the JFP2 depending on their needs. JFP1 is compliant with Intel ® Front Panel I/O Connectivity Design Guide .
81 Chapter 5 Front Panel Audio Connector: JAUD Y ou can connect an optional audio connector to the Front Panel Audio Header. JAUD is compliant with Intel ® Front Panel I/O Connectivity Design Gu id e .
Chapter 5 82 Front USB Connector: JUSB1 or JUSB2 The mainboard provides one front Universal Serial Bus connector for users to connect to USB devices. Users can choose either the JUSB1 or the JUSB2 depending on their needs. The JUSB1 is compliant with Intel ® Front Panel I/O Connectivity Design Guide.
83 Chapter 5 IrDA Infrared Module Header: JIR1 This connector allows you to connect to IrDA Infrared modules and is compliant with Intel ® Front Panel I/O Connectivity Design Guide. Y ou must configure the setting through the BIOS setup to use the IR function.
Chapter 5 84 Clear CMOS Jumper: JBA T1 There is a CMOS RAM on board that has a power supply from external battery to keep the data of system configuration. W ith the CMOS RAM, the system can automatically boot OS every time it is turned on. That battery has long life time for at least 5 years.
85 Chapter 5 Slots AGP (Accelerated Graphics Port) Slot The AGP slot allows you to insert the AGP graphics card. AGP is an interface specification designed for the throughput demands of 3D graphics. It introduces a 66MHz, 32-bit channel for the graphics controller to directly access main memory.
Chapter 5 86 PCI Interrupt Request Routing The IRQ, abbreviation of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor.
87 Chapter 5.
88 This chapter gives you the FRU (Field Replaceable Unit) listing in global configura ti ons of Aspire 3300S. Refer to this chapter whenever orderi ng for parts to rep air or for RMA (Return Merchandise Authorization).
89 Chapter 6 Aspire 3300S Exploded Diagram.
Chapter 6 90 Picture No. Partname Description Part No. FDD/Floppy Disk Drive 3 FDD MITSUMI 3 MODE FDD 1.44MB 1”H/D353M3D-R694005 KF .35301.001 NS U6 20G 5400RPM Seagate 56.02002.001 U6 40G 5400RPM Seagate 56.02002.01 1 U6 60G 5400RPM Seagate 56.02002.
91 Chapter 6 NS IDE Cable 80-pin 50.A33V5.003 8 FDD CABLE 34/34PIN 280MM 50.A33V5.004 1-1 1 TURBO LED CABLE 2PIN 500MM 50.A33V5.001 1-10 CD-IN CABLE 400MM 50.A33V5.008 1-9 POWER SW/HDD & POWER LED 50.A33V5.005 Main Board NS MAINBOARD/J86M J86M MB.
Chapter 6 92 NS Willamette 1.7G Socket 478 Will amette 1.7Ghz/400FSB 01.WILAM.1GV Willamette 1.8G Socket 478 Will amette 1.8Ghz/400FSB 01.WILAM.1GW Willamette 1.9G Socket 478 Will amette 1.9Ghz/400FSB 01.WILAM.1GK Willamette 2.0G Socket 478 Will amette 2.
93 Chapter 6 Boards NS DAUGHTER BOARD 54.A33V5.001 NS VGA CARD 54.02001.061 NS 1394 CARD IF .13901.002 NS MODEM CARD V92 56K HSFI LB 54.0901 1.551 54.09262.171 Power Supply 2 POWER SUPPL Y 160W FSP160-60SA V NOPFC 56.04180.001 Foot S tand 7 FOOT ST AND 60.
Chapter 6 94 NS FRONT P ANEL ASSY FRONT BEZEL VT3200 H34 60.A33V5.002 1-4 ROT A TE BRACKET ASSE MBL Y ROT A TE BRACKET H34A 60.A33V5.003 1-5 I/O BRACKET ASSEMBL Y IO BRACKET(S81M)H34A 60.A33V5.001 USB EMI COVER 34.A33V5.001 SOFT MOUNT FOR HDD 42.A33V5.
95 Chapter 6.
Appendix A 96 The Acer Aspire 3300S Mode l No. Define: 1. T rade Mark: 2. Brand Name: Acer 3. Product Name: Acer Aspire 3300S Model Definition and Configuration Appendix A.
97 Appendix A.
Appendix B 98 This computer ’s compat ibility is tested and verified by Acer ’s internal testing department. All of it s system functions are tested under Windows XP . Refer to the following lists for components, adapter card s, and peripherals which have passed these tests.
99 Appendix B Microsof t Wi ndows XP Environment T est Item Specifications AGP VGA Card ASUS AGP-V7700Deluxe (GeForce 2 G TS) ASUS V8200 (GeForce 3) ELSA Gladiac 51 1 (GeForce 2 MX400) ELSA Gladiac 92.
Appendix B 100 Floppy Disk Drive EPSON SMD-1300 1.44MB NEC FD1231H 1.44MB TEAC FD235HF 1.44MB SONY MPF920-E/161 1.44MB Panasonic JU-257A606P 1.44MB Mitsumi D353M3 1.44MB Panasonic JU-81 1 T012 ZIP Drive 100MB Panasonic LS-120 (LKM F934-1) 120MB Iomega Z100A T API ZIP 100MB Sound Card Creative Sound Blaster Live! (CT4620) Creative Sound Blaster 5.
101 Appendix B Keyboard Microsoft Natural Keyboard Pro BTC Keyboard 5200 TU Mouse Logitech M-UB48 Logitech Ifeel MouseMan M-UM53B GamePad Microsoft Side Winder FreeS tyle Pro Joystick Logitech Wingman.
Appendix C 102 This section describe s online techni cal support servic es available to hel p you repair your Acer Systems. If you are a distributor , dealer , ASP or TPM, please re fer your techn ical queries to your local Acer branch office. Acer Branch Offices and Regional Business Un its may access our website.
103 Appendix C.
104 A Advanced O ptions 43 PnP/PCI 44 Assignment Map 18 Audio controller 16 Audio Interface 16 B BIOS Setup 24 Entering Setu p 25 Setup Utility 25 System Informa tion 26 BIOS Utility 45 Advanced Op ti.
105 floppy disk drives A/B 29 IDE prima ry channel ma ster 29 IDE prima ry channel slave 29 IDE secondary channel master 30 IDE secondary channel slave 30 DRQ Assignment Map 20 E ECP 17 Environmental .
106 Jumper and Connector Information 76 Jumpers 76 K keyboard 12 M Machine Disassembly 48 cover 51 Housing Co ver 51 Main board 77 Main Board Layout 9 Mechanical S pecifications 21 Memory removin g 57 size 15 system 15 Memory Address Map 18 Microsoft DOS V6.
107 system sleep timer 39 system wake-up event 39 Power-On Self-T est (POST) 63 Product Information 27 BIOS Release Date 28 main boa rd ID 28 main board S/N 28 product name 28 SMBIOS versio n 28 Syste.
108 Advanced Op tions 43 Boot Options 40 Date 41 Disk D rives 29 Onboard Peripherals 32 PnP/PCI Options 44 Power Mana gement 35 Product Informatio n 27 System Security 42 Time 41 T T emperature 20 T e.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Acer 3300S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Acer 3300S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Acer 3300S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Acer 3300S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Acer 3300S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Acer 3300S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Acer 3300S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Acer 3300S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
