Manuel d'utilisation / d'entretien du produit DX8000-MUX16 du fabricant Pelco
Aller à la page of 24
DX8000-MUX16 Installation Manual C1601M (6/04) Digital Video Recorder DX8000.
Protecting people and property in a million locations worldwide..
C1601M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-MUX16 analog output adapter . PARTS LIST Qty Description 1 DX8000-MUX16 multiplexing analog output card 1 Adhesive-backed part label Figure 1.
2 C1601M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools.
C1601M (6/04) 3 Figure 3. Removing Power Cord from Unit.
4 C1601M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electro static discharge (ESD). Before handling any electronic components, you should take steps to properly ground yourself so that any built-up static electric charges are dissipated away from the unit.
C1601M (6/04) 5 Prepare the Unit OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the unit chassis: a.
6 C1601M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section.
C1601M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity .
8 C1601M (6/04) REMOVE THE REAR CROSS-BRACE 1. Using a Phillips-head screwdriver , remove the two flat-head screws that secure the rear cross-brace. Refer to Figure 7.
C1601M (6/04) 9 2. Move the rear cross-brace aside and keep the screws for later use. Figure 8. Moving Rear Cross-Brace to Rear of Unit.
10 C1601M (6/04) Install the DX8000-MUX16 Card 1. Locate PCI Slot 2 on the system motherboard. Refer to Figure 9. Figure 9. Location of PCI Slot 2 PCI SLOT2.
C1601M (6/04) 11 2. Remove the slot cover covering PCI Slot 2: a. Using a Phillips-head screwdriver , remove the screw that fastens the slot cover to the chassis. Refer to Figure 10. Retain this screw for use in step 4d. b. Remove the slot cover from PCI Slot 2.
12 C1601M (6/04) 3. Carefully remove the DX8000-MUX16 card from its static-safe packaging. Handle the adapter card by its edges and slot cover , and avoid contact with the card’ s components, connectors, and conductive leads. 4. Insert the DX8000-MUX16 card in PCI Slot 2: a.
C1601M (6/04) 13 d. Using the screw you removed in step 2a, secure the DX8000-MUX16 card to the chassis. Refer to Figure 12. Figure 12. Securing the DX8000-MUX16 Card 4d.
14 C1601M (6/04) 5. Connect video data cables: a. Connect the rear video input ribbon cable from the primary capture card to the DX8000-MUX16 card. Refer to Figure 13.
C1601M (6/04) 15 b. Connect the front video input ribbon cable from the secondary capture card to the connector on the daughter board of the DX8000-MUX16.
16 C1601M (6/04) c. Connect the video output ribbon cable from the DX8000-MUX16 card to the VGA card. Refer to Figure 15. Figure 15. Video Data Cable Connections 5c.
C1601M (6/04) 17 Reassemble the Unit 1. Replace the rear cross-brace and secure it with the flat-head screws you set aside earlier . Refer to Figure 16.
18 C1601M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 17. Figure 17. Replacing Chassis Cover.
C1601M (6/04) 19 3. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door .
20 C1601M (6/04) ON/OFF 4. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 5. Plug the power cord back into the power supply and then into the wall. 6. T urn on the power switch and allow the unit to start up and find the new hardware.
PRODUCT W ARRANTY AND RETURN INFORMA TION PRODUCT W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
C1601M (6/04) ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco DX8000-MUX16 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco DX8000-MUX16 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco DX8000-MUX16, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco DX8000-MUX16 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco DX8000-MUX16, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco DX8000-MUX16.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco DX8000-MUX16. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco DX8000-MUX16 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
